Building Material HEC for Wall Putty Powder Hydroxyethyl Cellulose

China Building Material HEC for Wall Putty Powder Hydroxyethyl Cellulose, Find details about China Hydroxyethyl Cellulose, Water Retention from Building Material HEC for Wall Putty Powder Hydroxyethyl Cellulose

Model NO.
SK1000
Granularity
98% Pass 80 Mesh
Loss on Drying
≤6
Molar Substitution
1.5-2.0
Viscosity
85000-100000
Trademark
YI DA
Transport Package
PP Bags with Inner PE Bags
Specification
25kg per bag
Origin
Hebei, China
Model NO.
SK1000
Granularity
98% Pass 80 Mesh
Loss on Drying
≤6
Molar Substitution
1.5-2.0
Viscosity
85000-100000
Trademark
YI DA
Transport Package
PP Bags with Inner PE Bags
Specification
25kg per bag
Origin
Hebei, China
Product Description 
Yida hydroxyethyl cellulose (HEC)SK1000 Yi da scientific research team specifically for the development of a product lacquer, product thickening suspension effect is good, high water retention rate, good spray gun, less sand. Small addition amount and low unit price can reduce production cost.

Building Material HEC for Wall Putty Powder Hydroxyethyl Cellulose
Property index
 
TypeSK1000
AppearanceWhite or light yellow powder
Granularity98% pass 80 mesh
Water content /%≤5
PH value6-8
Viscosity (2%,20ºC)  85000-100000

The recommended dosage of this product is 2-4‰ of the system.
The dosage should be determined by test.

 

 

Building Material HEC for Wall Putty Powder Hydroxyethyl Cellulose
Application
 
Building Material HEC for Wall Putty Powder Hydroxyethyl Cellulose
SK1000 is widely used in the production of lacquer, play a good effect of thickening suspension.
 
System kindThe test content /‰state description
stone-like coating1.5Good spray, less sand fall
 

Adding method
(1) Pre-dissolve in other containers beforehand. The specific steps are to weigh water, stir with electric drill, and slowly add hydroxyethyl cellulose until it is completely dissolved. Pour the predissolved cellulose solution directly into it in the formal production process.
(2) Sprinkle hydroxyethyl cellulose directly and slowly in the production process until it is completely dissolved.
(3) half pre-dissolved, half sprinkled in the mass production process.
(4)Either in the preparation of pre-solution or in the production process directly sprinkled with hydroxyethyl cellulose, do not pour all at once, can only use a vessel or hand slowly sprinkled, as far as possible to avoid cellulose agglomeration.

(5)In the production process without adding hydroxyethyl cellulose before adding multifunctional additives, otherwise cellulose is easy to agglomerate a knot.

Matters need attention
(1)To sprinkle hydroxyethyl cellulose in the manufacturing process, the equipment must be turned on first, and then slowly sprinkle cellulose after the equipment has rotated.
(2)Viscosity change: a moment of high viscosity and the state is rough, continue to stir for a few minutes after the viscosity tends to be stable, the state is improved significantly.
(3)Such as simple test cellulose aqueous solution viscosity, can be completed on the first day of aqueous solution, the second day of viscosity test, and observe the state.Because there are many bubbles in the just-prepared aqueous solution, the transparency and viscosity test indexes are not accurate due to its influence

Storage 

*After the product is opened and used, it must be sealed in time.
*This product is thermoplastic, so it should be stored in a high-temperature environment to avoid pressure. Otherwise, it will easily cause agglomeration. 
*Sealed and stored in a cool and dry place at 0-40ºC, and the storage time should not exceed 24 months.
Building Material HEC for Wall Putty Powder Hydroxyethyl Cellulose
Building Material HEC for Wall Putty Powder Hydroxyethyl CelluloseBuilding Material HEC for Wall Putty Powder Hydroxyethyl CelluloseBuilding Material HEC for Wall Putty Powder Hydroxyethyl Cellulose

Service
1- Professional construction-grade cellulose ether supplier.
2- Construction chemicals and technology solutions provider.
3- Free formulations for construction grout mortar.

 

Technical Support
During the preparation of various formula systems for this product, the Yida technical team can provide technical consultation, technical tracking, and long-term optimization of the formula system.

FAQ

Q1: Are you a manufacturer or trading company?
A: Manufacturer. 

Q2: What are your terms of payment?
A: Accept LC, TT, West Union Payment. Others can be negotiated. 

Q3: What are your terms of delivery?
A: EXW, FOB, CFR, CIF, DDU.

Q4: How about your delivery time?
A: The goods would be shipped within 5 days if stock is available. We confirm the delivery date according to your order if the stock is not enough.

Q5: Can you provide samples for free?
 A: Allowed. We provide free samples, buyers pay for freight.