Big air volume Activated carbon smoke filter and welding gas purifier

Applications :Qingdao Loobo welding fume extractor are mainly used to extract/collect the fume and dust in the metal fabrication process, like the welding, polishing, grinding, metal cutting, etc.

With active carbon filter layer, some odor gas can be absorbed before released the clean air. Portable type with small size, you can move them freely in your workshop to the working posation, economic and high efficiency.  


 

LB-JW Industrial activated carbon smoke filter from LOOBO manufacturer

Use for purification of the smoke and dust during the welding, polishing, cutting, grinding process ,can purify large amounts of suspended small metallic particles in the air.

* Operating Principle:

1,  Polluted air through the pre-filter, been preliminary filter to filter out the big particles ( the filter replacement convenient ).

2,  The main filter under the pre-filter, it can filter out harmful gases in the air, clean air from the bottom of the equipment is returned to the workshop.

**LB-JW Series Welding Fume Purifier Parameters Table

Custom design and production is available.

***Facility Characteristics

1)      It is attached with all-direction caster wheels, which makes the facility movable freely and easy to position. 

2)      Advanced fan design, large air volume, low power consumption

3)      It can equip with one or two suction arms, the arm is all-directions sucking arm of 360 degree rotating. It can suck the fume exactly from the source which make best of the fume collection efficiency, and insure the workers' health in the largest extent. 

4)       Use the load protection device for the electronic control, simple structure, and high safety, convenient for operation.

5)      The filter core is imported from America with long useful life. Filtering effect is 99.9%, can absorb 0.3μm particles. The filtering effect is good for all kinds of particles including the wet particles.6)       

7)      Clean air uniform guidance and dispersed from the grille outlet, to keep the noise minimum.

8)      Pre filter layer put on the easily changed filter net, convenient cleaning and replacement.

JW Carbon air filter for welding

Industrial waste gas honeycomb activated carbon purification equipment

Technical principle:

Honeycomb activated carbon is a new kind of environmental protection and purifying product can effectively reduce odor and pollution.

The main raw materials of this product are advanced coal activated carbon powder, high iodine value coconut shell activated carbon powder, super discoloring wooden activated carbon powder, it is the most advanced coal activated carbon powder,

Activated carbon is made into honeycomb shape so called honeycomb activated carbon.

Suitable for large air volume, low concentration plant organic waste gas (three benzene and toxic or harmful gases)treatment.

Suitable for indoor air purification, dining lampblack waste gas treatment.In addition to the peculiar smell. And also can be regard as a catalyst carrier.

 Technical Parameter Table:

Scope of application:

Used for gas phase activated carbon adsorption, benzene, toluene, xylene, acetone,and CS2 and other organic solvent adsorption and recovery of oil and gas.

Cigarette filter tip, in addition to taste, decorate indoor air purification(Removal of formaldehyde, benzene and other harmful gases),industrial gas purification (such as CO2, N2, etc.).

Petrochemical industry production, gas purification, desulfurization, deodorization, treatment of waste water.

Biochemical, paint industry, leather factory, animal feed, underground places, places

of air purification and deodorization.

Adsorption of stack gas odor and sulphide, removing of mercury steam, reducing the generation of dioxin.

Use for purification of the smoke and dust during the welding, polishing, cutting, grinding process and the recycling of rare metals and precious material, can purify large amounts of suspended small metallic particles in the air. 
 * Operating Principle:

It is equipped with three layer filter system

1, under the help of the fan device, the welding fume is sucked into inlet through sucking hood. There is the flame arrester in the inlet, so the spark can be blocked here, the left fume and dust is sucked into gravity separator, and then the bigger particles firstly descend into dust bag. 
2, the smaller particles are arrested in the surface of core filter. The cleaner gas then flow into clean room after being purified by core filters.
3, in clean room, the clean gas is then further purified by active carbon. At last, the gas meets the required standards and enters into air or other required room.

**Facility Characteristics

1)      It is equipped with ABB turbo fan and motor imported from Germany and America, with overload prevention circle to avoid motor damage. It is of steady performance. 
2)      It is equipped with built-in centralized PLC controlling system. The operation panel is clear and simple, very easy to operate. 

3)      Pulsing back-flushing automatic dust-removal system: The filter core is the automatic rotating and back-flushing type, which keeps the filter core surface clean when working, to insure the stable blowing rate; the air compressor parts are connected with high pressure rubber pipe with high pressure air-inflow in the bottom, which insure the facility always in good working condition.

4) The filter core is imported from America with long useful life. It can arrest the 0.3μm particles. The filtering effect is good for all kinds of particles including the wet particles.

 5) It is equipped with the all-directions sucking arm of 360 degree rotating. It can suck the fume exactly from the source which make best of the fume collection efficiency, and insure the workers' health in the largest extent. 

6) It is equipped with three layer filter system to avoid the damage effect of flame and large slag particles, which extend the useful life, safer and more reliable. 

7) Clean air uniform guidance and dispersed from the grille outlet, to keep the noise minimum.

8) It is attached with all-direction caster wheels, which makes the facility movable freely and easy to position.

9) Photoelectric controlled on/off, energy saving and high efficiency. The hood has the lighting device which is upon customer's choice. 

10) The parts working condition are all stable and have long useful life, meantime easy to be replaced.  

 Welding dust collector, welding fume extraction,welding smoke extractor, welding fume exhaustor, welding fume purifier, smoke eater from source

LB-JZ Series Welding Fume extractor Parameters Table, Maunal cleaning type:

 LB-JZD Series Welding Fume Purifier Parameters Table, Auto cleaning type:

The JZ(D) is basically same to the JZ. The main difference is when you connect air compressor to back-flush for cleaning cartridge, the back-flushing of JZ(D) can be auto-controlled by pulse valve; while the back-flushing of JZ is manual type. Compare with JZ series, JZ(D) is suitable for the heavy smoke workshop.

  Custom design and production is available.

Comapny Information:

Qingdao Loobo Environmental Protection Technology Co.,Ltd is one of the biggest enviromental protection products manufacturer, located in Qingdao city of china,specialized in alll kinds of portable fume extractor, downdraft benches(grinding dust removal worktable), central fume purification system, flexible suction arm,etc.

We have more than ten years export experience ,all of our products with the ISO9001 and CE certification, the quality can be guaranteed.

We have our own R&D department , have a variety of style range to meet any of your requirments and had established the economies of scale, so can dilivery fast and provide can beat your competitor's price.

Best Regards

Miss Juno