Products

Factory Supply Handpush Concrete Scarifier Machine Price

China Factory Supply Handpush Concrete Scarifier Machine Price, Find details about China Miling Machine, Scarify Machine from Factory Supply Handpush Concrete Scarifier Machine Price

Model NO.
ZT
Certification
ISO9001: 2000
Condition
New
Model
Zt70
Drilling Diameter
83-100mm
Cylinder Diameter
90mm
Power
3kw
Weight
380V
Trademark
ZHONGTUO
Transport Package
Wooden Box
Specification
electric
Origin
China
Model NO.
ZT
Certification
ISO9001: 2000
Condition
New
Model
Zt70
Drilling Diameter
83-100mm
Cylinder Diameter
90mm
Power
3kw
Weight
380V
Trademark
ZHONGTUO
Transport Package
Wooden Box
Specification
electric
Origin
China
Factory Supply Handpush Concrete Scarifier Machine PriceDescription:
1 simple operation, high efficiency!
2 with easy maintenance, power, easy to move and so on
3 to remove the ground coating, paint, a variety of road marking;
4 damaged ground, the need for renovation of the plot, remove the old floor surface;
5 into the quality of heaven and earth, bring unlimited business opportunities

scarifying machine is a light motor drive ground milling machine to 7.5kw kilowatts Y132M-4 variable speed motor as the driving force, the use of forward cutting the working principle, can quickly cut the ground material! Working principle: Unlike the large-scale milling machine's anti-cutting principle, the small milling machine relies on the positive high-speed rotation of the milling drum, so as to shake the six groups of hard tungsten steel alloy blades on the milling cutter shaft. , The use of alloy blade on the tungsten steel alloy teeth to break and ground the ground material, so as to achieve the effect of surface milling;

use:
concrete scarifier machine Mainly used for highway, urban roads, airports, freight yard and other asphalt concrete surface of the excavation renovation, can also be used to remove the road package, oil waves, textures, rutting and other defects can also be used to excavate pits and ditch Groove, and the cement road surface of the hair and the surface of the wrong level of milling.


parameters:
Technical projectmodel:WC-200Gmodel WC-255G
Power configurationThree-phase asynchronous motor / 5.5KW (CW200D)
Honda GX270 Gasoline Engine / 13HP (WC200F)		Three-phase asynchronous motor / 7.5KW (CW255D)
Honda GX270 Gasoline Engine / 13HP (WC255F)
Number of knife shafts6 root6 root
Number of blades78 pieces (6 teeth)108 pieces (6 teeth)
Bearing seal formSealed (maintenance-free)Sealed (maintenance-free)
A milling width200mm250mm
A milling depth3mm-5mm3mm-5mm
weight90kg115kg
Long × wide × high1125×500×1125mm1125×500×1125mm
Hourly work efficiency150 square170 square
Walking wheel4 only4 only
Air damping tube2 only2pc
Counterweight 25kg(standard)

4. concrete scarifier machine use and maintenance
1 machine is the main part of the work due to milling cutter, bearings, gaskets, milling drums, the operation process due to a long time with the road friction, the fastest consumption is this part of the regular replacement, inspection in order to better extend the use of the machine life;
2, milling cutter shaft should be checked daily, if the above grinding out of the slot more than 25% of the diameter of the knife, you have to replace. In general, the life of the knife shaft is half the life of the tungsten steel cutter. scarifying machine From the square area, the life of the milling depth of 5mm when about 350-500 square meters. But please pay attention to, there are many factors that will affect the life of the knife shaft, so to check every day;
3, for safety reasons, before the maintenance, should first pull the engine spark plug, preferably by the qualified mechanic;
4, each time before running to check the oil level, after use to clean the air filter;
5, every 4 hours after use, to grease the bearing. concrete scarifier Hit the grease, while playing side of the rotation drum, so that grease coated in the entire bearing;
6, before each operation with the naked eye to check the machine: all fasteners are tightened? Are there any parts of the obvious wear or cracking? Oil pipeline is intact? Check the bearings, check the cover is covered;
7, before each operation, to check the belt tightness. The new belt should be reoriented after 4 hours of operation, and the belt tension must be maintained in order to transmit the output horsepower of the engine to the cutter drum. scarifier concrete grinder When the tight belt is too tight, the belt will be easily worn and the bearing life will be shortened , If broken, serious wear and tear of the belt should immediately change the new; forget the past to have a new start. 
8, in general, milling cutter cracking is very rare, if any, usually shows the following: a: milling cutter on the irregular arrangement; b: a single milling too deep; c: the use of inappropriate milling Knife to remove the different types of road; d: milling the surface strength is too large; to be courage to admit their mistakes, and bear the responsibility.
9, each time you change the milling cutter arrangement, check the cutter shaft and the bearing. If the shaft appears to wear the groove, you need to replace the new, when the axis for the same time for bearings;
10, milling drum if properly maintained, usually can be used for 3 months. When checking the milling cutter or doing maintenance, check whether there is any cracks in the center axis of the milling drum, whether the sleeve hole is oval, whether there is any crack at the weld, and if there is any damage,
11, and finally, when you want to check the milling machine at the bottom of the milling machine, reminded that: the machine must be tilted forward, never backward, or oil will pour into the engine cylinder.
 
ModelZT70ZT100ZT120
Drill Diamterφ60-80mmφ83-100mmφ85~130mm
Rock hardness≥20≥20≥20
Drill Depth≥15m≥3030-40m
Swing speed110r/min90r/min90r/min
Air pressure0.5-0.7Mpa0.5-0.7Mpa0.5~1.0Mpa
Air consumption≥3.5m3/min6M3/min10m3/min
Cylinder Diameter90mm90mm90mm
Valid Distance1070mm1070mm1200mm
Propulsion3600N6000N9600N
Power3kW3kW3kW
Voltage380V380V380V
Rated speed1410r/min1410r/min1410r/min
Outer Diameterφ42mmφ42mmφ42mm
Drill Pipe Length1025mm1025mm1025mm
Size1740×260×420mm1800*650*400mm1800*700*450mm
Weight220kg250kg300kg 
      
Factory Supply Handpush Concrete Scarifier Machine PriceShaanxi Zhongtuo Mining Equipment Co., Ltd. is a global supplier who specializing in bridge stretching
equipment, downhole drill series, steel processing machinery, rock splitting equipment, grouting equipment
and pavement processing equipment. After years of hard work and development. We have established a
solid foundation for providing quality services with many years of experience in mechanical equipment
manufacturing. Our high-quality bridge equipment and mining machinery products such as bridge
stretching equipment, downhole drill series, steel processing machinery, rock splitting equipment,
grouting equipment and pavement processing equipment have been well received by users. In recent years
we have begun to focus on the development of international markets. ?With the continuous improvement of
high-quality products and high-quality services, our products are highly appreciated by customers in the
international market. Due to the excellent performance of the products and professional after-sales service
, our products have been sold to: Romania, Bulgaria, Albania, Colombia, Brazil, Peru, Uruguay, Saudi Arabia,
Kuwait, United Arab Emirates, Oman, Turkey, Israel, Kazakhstan, Sudan, Madagascar, etc. We have been
focusing on high-quality mechanical equipment and construction products for more than 20 years, and are
widely used in mining, construction and water conservancy projects, railway

Factory Supply Handpush Concrete Scarifier Machine PriceFAQ:
Q1: Are you factory or trade company?
A1: We are factory. And we have ourselves trading company.
 
Q2: What the exactly address of your factory?
A2:  No.27,Beichen Village Industrial Park, Weiyang District, Shaanxi Province China.                                                                                                                            
Q3: Warranty terms of your machine?
A3: One year warranty for the machine and technical support according to your needs.

Q4: Will you provide some spare parts of the machines?
A4: Yes, of course.

Q5: What about the voltage of products? Can they be customized?
A5: Our standard voltage is 380V, 50HZ, 3phase. The voltage can be customized according to your equirement.
 
Q6: Which payment term can you accept?
A6: 100% T/T( Decide according to actual situation)

Q7: How long will you take to arrange production?
A7: we can delivery the normal goods within 7-15 days. Other nonstandard electrical items we will delivery within 25-30 days.
 
Q8: Can you accept OEM orders?
A8: Yes, with professional design team, OEM orders are highly welcome.
 
Q9: Which trade term can you accept?
A9: Available trade terms: FOB, CIF, CFR, EXW, etc.

Q10: Do you provide samples? Is it free or extra?
A10: Yes, we could offer you the sample machine. But it's not free. You need to pay for the sample and the cost of freight.

Q11: What is your terms of payment?
A11: We accept T/T, Western Union, Money Gram, Paypal, L/C, etc.
   
 

You Might Also Like