Battery Pack for storage

China Battery Pack for storage, Find details about China Lithium Battery Li-ion Battery, LFP LiFePO4 from Battery Pack for storage

Basic Info.

Model NO.

AP48100

Rated Capacity

50ah 100ah

Standard Voltage

48V

Usage

Home storage Ess Bess

Electrolyte

Li-ion

Trademark

Allsparkpower

Transport Package

Standard Export Package

Specification

LFP 48V 100Ah

Origin

China

HS Code

8504402000

Model NO.

AP48100

Rated Capacity

50ah 100ah

Standard Voltage

48V

Usage

Home storage Ess Bess

Electrolyte

Li-ion

Trademark

Allsparkpower

Transport Package

Standard Export Package

Specification

LFP 48V 100Ah

Origin

China

HS Code

8504402000

Product Desciption

Item		parameters	Note
Cell	Type	LiFePO4 Battery
	Cell Model	LF50116160-100	LFP
	Nominal Capacity	100Ah	Discharge : 0.5C Cut-off Voltage:2.5V
	Minimum Capacity	100Ah	Discharge : 0.5C Cut-off Voltage: 2.5V
	Nominal voltage	3.2V
	Internal Impedance	≤1.5mΩ
	Dimension	Max.49.9x116x160mm
	Weight	Approx.1.95kg
Batterypack	Pack Method	15S1P
	Nominal Capacity	100AH	Discharge : 0.5C Cut-off Voltage:37.5V
	Minimum Capacity	100AH	Discharge : 0.5C Cut-off Voltage: 37.5V
	Nominal Voltage	48V
	Energy	4800Wh
	Charge Voltage	54.75V
	Discharge cut-off voltage	37.5V
	Charge Method	CC/CV
	Standard Charge Current	50A
	Max. Charge Current	100A
	Standard Discharge Current	50A
	Max. Continues Discharge current	100A
	Cycle Life	3500 times()
	Internal Impedance	≤15mΩ
	Dimension	L482(L1 442)xW420Xh177.5mm
	Output Wire	/
	Output Connector	UES0601LBNBA ,25 ,,6.0 ,	Charge discharge port
	Communication	RS485/RS232/CAN

	Weight	Approx.48kg
	Working Temperature Range	Charge: 0°C--45°C Discharge: -20°C--60°C
	Storage Temperature	-10°C--50°C

BMS BMS Parameters
1. main parameters setting

No.	Item		Default parameters	Setting or not		note
1	Cell overcharge protection	Alarm voltage	3600mV	Yes
		Protection voltage	3700mV	Yes
		Protection time delay	4.0S	Yes
	Cell overcharge protection released	Released voltage	3380mV	Yes
		Released Capacity	SOC<96%	Yes
		Discharging released	Discharging current > 1A
2	Cell over discharge protection	Alarm voltage	2800mV	Yes		After 30 seconds of over‐discharge protection, if it still cannot be recovered, it will enter the low
		Protection voltage	2500mV	Yes
		Protection time delay	1.0S	Yes
	Cell over discharge protection released	Released voltage	2900mV	Yes
		Charging	Connect with charger
3	Pack overcharge protection	Alarm voltage	54V	Yes
		Protection voltage	55.5V	Yes
		Protection time delay	4.0S	Yes
	Pack overcharge protection released	Released voltage	50.7V	Yes
		Released Capacity	SOC<96%	Yes
		Discharging released	Discharging current > 1A
4	Pack over discharge protection	Alarm voltage	42V	Yes		After 30 seconds of over‐discharge protection, if it still cannot be recovered, it will enter the low
		Protection voltage	37.5V	Yes
		Protection time delay	1.0S	Yes
	Pack over discharge protection released	Released voltage	43.5V	Yes
		Charging	Connect with charger
5	Over charge current protection	Alarm current	105A	Yes		10 times consecutive occurrences will lock this state and will no longer be automatically released
		Protection current	110A	Yes
		Protection time delay	1.0S	Yes
	Released over charge current protection	Automatic release	After 1min
		Charging	Discharging current > 1A
6	Over discharge current protection 1	Alarm current	105A		Yes	10 times consecutive occurrences will lock this state and will no longer be automatically released
		Protection current	110A		Yes
		Protection time delay	1.0S		Yes
	Released over discharge current protection 1	Automatic release	After 1min

		Charging release	Discharging current > 1A
7	Over discharge current protection 2	Protection current	≥150A	Yes	10 times consecutive occurrences will lock this state and will no longer be automatically
	Over discharge current protection 2	Protection time delay	100mS	Yes
	Released over discharge current	Automatic release	After 1min
	Released over discharge current	Charging release	Discharging current > 1A
8	short‐circuit protection	Protection current	≥350A
		Protection time delay	≤300μS
		Protection released	charging
		Protection released	Off load
9	MOS High temperature protection	Alarm temperature	90ºC	Yes
		Protection Temperature	110ºC	Yes
		Released temperature	85ºC	Yes
10	Cell temperature protection	Low temperature charging	0ºC	Yes
		Low temperature charging Protection	‐5ºC	Yes
		Low temperature charging Protection released	0ºC	Yes
		High temperature charging alarm	55ºC	Yes
		High temperature charging Protection	60ºC	Yes
		High temperature charging Protection released	50ºC	Yes
		Low temperature discharging alarm	‐15ºC	Yes
		Low temperature discharging Protection	‐20ºC	Yes
		Low temperature discharging Protection	‐15ºC	Yes
		High temperature discharging alarm	60ºC	Yes
		High temperature discharging Protection	65ºC	Yes
		High temperature discharging Protection	55ºC	Yes
11	Ambient temperature protection	Low temperature alarm	‐15ºC	Yes
		Low temperature protection	‐20ºC	Yes
		Low temperature protection released	‐15ºC	Yes
		high temperature alarm	65ºC	Yes
		High temperature	75ºC	Yes
		High temperature protection released	65ºC	Yes
	Current consumption	Working self‐consumption	≤45mA(with display)

12		current	≤40mA(without display)
		Low Energy running mode	≤100μA
13	Balancing	Pack voltage difference	3500mV	Yes	open
		Cell Voltage difference	30mV	Yes
14	Default capacity	Low capacity alarm	SOC<5%	Yes	There is no alarm when charging
15	Sleep feature	sleep Voltage	3150mV	Yes
		Time delay	5min	Yes

3.2.LED LED instruction

Table 1 LED Working status indicator

Status	Normal/Alarm /Protection	ON/ OFF	RUN	ALM	LED status						Note
Status	Normal/Alarm /Protection										Note
Shutdown	Sleep	Off	Off	Off	Off	Off	Off	Off	Off	Off	All off
Standby	Normal	Normally on	flicker 1	Off	The battery capacity status
Standby	Alarm	Normally on	Flicker1	Flicker3	The battery capacity status						Low voltage
Charging	Normal	Normally on	Normally on	Off	The battery capacity status ( max capacity LED flicker 2)						Over charge status, the ALM light will not flicker
	Alarm	Normally on	Normally on	Flicker3	The battery capacity status ( max capacity LED flicker 2)						Over charge status, the ALM light will not flicker
	Over charge protection	Normally on	Normally on	Off	on	on	on	on	on	on	If no charging, the LED status will be standby
	Temperature,over current , failure protection	Normally on	Off	Normally on	Off	Off	Off	Off	Off	Off	Stop charging
Discharging	Normal	Normally on	Flicker3	Off	The battery capacity status
	Alarm	Normally on	Flicker3	Flicker3	The battery capacity status
	Low voltage protection	Normally on	Off	Off	Off	Off	Off	Off	Off	Off	Stop discharging
	Temperature,over current , failure protection	Normally on	Off	Normally on	Off	Off	Off	Off	Off	Off	Stop discharging
Failure		Off	Off	Normally on	Off	Off	Off	Off	Off	Off	Stop charging or discharging

Table 2 battery capacity status specification

status

charging

discharging

Capacity LED light

capacity(%)

0~16.6%

Off

ON 1

16.6~33.2%

Off

On 1

Off

On 1

33.2~49.8%

Off

On 1

Off

On 1

49.8~66.4%

Off

On 1

Off

On 1

66.4~83.0%

Off

On 1

Off

On 1

83.0~100%

On 1

Running LED

Normally on

Note: F2: flicker 2 ; On 1: normally on ; F3: flicker 3

Table 3 LED flicker status

Flicker model	on	off
Flicker 1	0.25S	3.75S
Flicker 2	0.5S	0.5S
Flicker 3	0.5S	1.5S

1. Description of buzzer action

Fault: Every second, Buzzer works 0.25S;
Protection: Every 2 seconds, Buzzer works 0.25S;(except over voltage protection) Alarm: Every 3 seconds, Buzzer works 0.25S;(except over voltage protection)
The buzzer function can be enabled or disabled by the host computer, and the factory default is disabled.

1. Buttons Description

When the BMS is in the sleep state, press the button (3~6S) and release, the protection board is activated, and the LED indicator lights up in sequence from "RUN" for 0.5 seconds.
When the BMS is activated, press the button (3~6S) and release it, the protection board is dormant, and the LED indicator lights up in order from the lowest battery light for 0.5 seconds.
When the BMS is in the activated state, press the button (6~10S) and release it, the protection board is reset, and the LED lights are all lit simultaneously for 1.5 seconds.
After the BMS is reset, the parameters and functions set by the host computer are retained. If you need to restore the initial parameters, you can use the "restore default value" of the host computer to achieve, but the related operating records and stored data remain unchanged (such as power, cycle number, Record protection, etc.)

1. Sleep and wake up status
  1. Sleep status

When any of the following conditions are met, the system enters a low‐power mode:

The single or overall over‐discharge protection has not been released within 60 seconds.
Press the button (3~6S) and release it.
The lowest monomer voltage is lower than the sleep voltage, and the duration reaches the sleep delay time (at the same

time, no communication, no protection, no balance, no current).

Standby time exceeds 24 hours (no communication, no charge and discharge, no commercial power).
Forced shutdown by the host computer software. Before entering sleep, make sure that the input terminal is not connected to an external voltage, otherwise it will not be able to enter the low power consumption mode.
1. 1. Wake up status

When the system is in low‐power mode and meets any of the following conditions, the system will exit low‐power mode and enter normal operation mode:

1. 1. 1. Connect the charger, and the charger output voltage must be greater than 48V.
    2. Press the button (3~6S) and release it.
    3. RS232 communication is activated (this method cannot wake up the motherboard due to over‐discharge).

Remarks: After single or total over‐discharge protection enters low power consumption mode, it wakes up regularly every 4 hours and turns on charge and discharge MOS. If it can be charged, it will exit the sleep state and enter normal charging; if it can not be charged after 10 consecutive automatic wakeups, it will no longer automatically wake up.
When the system is defined as the end of charging, the recovery voltage has not been reached after 2 days of standby (standby time setting value), and the charging is forced to resume until the end of recharging.

Appearance

,,,,,,.
It shall be free from any defects such as scratch, distortion, contamination and leakage.

Performance
1. Standard Test Condition

,,: :20±5ºC,: 65±20%,,15A ,, 5 ,
The battery shall be evaluated within 1 month from the arrival date.
Unless otherwise stated in these specifications, the following test shall be carried out in an ambient temperature of 20±5ºC, relative humidity of 65±20%
Discharge capacity when the battery is discharged at 15A to 37.5V after being standard charged. Five cycles are permitted for this test. The test shall be terminated at the end of the first cycle which meets the requirement.

1. Testing Instrument or Apparatus
  1. Dimension Measuring Instrument

0.01mm.
The dimension measurement shall be implemented by instruments with equal or more precision scale of 0.01mm specified.

1. 1. Voltmeter and Ammeter

10K/V, 0.01. Voltmeters and ammeters shall be equal or more precision instruments of 10K/V and 0.01.

1. 1. Impedance Meter

(1kHz LCR)
Impedance shall be measured by a sinusoidal alternating current method (1kHz LCR meter)

1. Electrical Performance

Item	Condition	Specification
Open-Circuit Voltage	,24 The open-circuit voltage shall be measured within 24hours after standard charge	≥49.5V
Battery Capacity	, 1 , 15A , The discharge time at 15A shall be measured after standard charge at 20±5ºC and rest 30mins	≥100%
Cycle Life	20±5ºC, 50A ,≤0.02C; 1 , 50A ; 1 , 3500 ,The discharge time on standard discharge shall be measured after 3500 cycles of standard charge and discharge at 20±5ºC,0.5C charge and discharge.	≥80%
Charge(capacity) retention	20±5ºC,, 28 , 15A , The discharge time at 15A shall be measured after standard charge and then storage at 20±5 ºC for 28days	≥80%
1 Temperature Characteristic1	, 55±2ºC 5h, 15A , After standard charging at 20±5ºC, laying the battery at 55ºC for 2hour, then discharge at 15A to 37.5V, record the discharge time	≥80%
2 Temperature Characteristic2	,-10±2ºC 16-24h, 15A , After standard charging at 20±5ºC, laying the battery at -10 ºC for 4hour, then discharge at 15A to 37.5V, record the discharge time	≥60%

Mechanical Performance

Item	Condition	Specification
Crush Test	,32mm , 17.2Mpa, 13KN, A battery is to be crushed between two flat surfaces. The force for the crushing is to be applied by a hydraulic ram with a 32mm diameter piston. The crushing is to be continued until a pressure reading of 17.2mmPa is reached on the hydraulic ram, applied force of 13kN. Once the maximum pressure has been obtained it is to be released.	, No fire, No explosion

Drop Test	1m ,() 1 The battery has only two axes of symmetry in which case only two directions shall be tested. The battery is to be dropped from a height of 1 meter twice onto concrete ground.	,, No explosion, No fire, No smoke
Vibration	, X,Y,Z 30 , 1.6mm A full-charged battery is to be subjected to simple harmonic motion with an amplitude of 1.6mm total maximum excursion. The frequency is to be varied at the rate of 1 hertz per minute between 10 and 55 hertz. The cell shall be vibrated for 30 minutes per axis o XYZ axes.	,, No leakage, No Fire, No explosion

Cell Safety Performance

Item	Condition	Specification
Over charge	20±5ºC, 1C 4V,4V 0A,, 10ºC,. At 20±5ºC, charging battery with constant current 1C to voltage 4V, then with constant voltage 4V till current decline to 0.	, No explosion, No fire
Over discharge	.20±5ºC, , 30mΩ 24 . At 20±5ºC, according to the requirement of the standard of discharge after discharge to termination voltage, 30 m Ω external load discharge within 24 hours.	,, No explosion, No fire
Short-circuit	20±5ºC,, 50mΩ, 6 . At 20±5ºC, Standard charge, across the electrodes of the battery with a less than 50 m Ω wire connection, 6 hours	, 150ºC No explosion, No fire The temperature of the surface of the cell are lower than 150ºC
Heating	, 5±2ºC, 130ºC, 30 Battery is heated in a circulating air oven at a rate of 5±2ºC per mins to 130ºC, an then placed 30 mins at 130ºC	, No explosion, no fire

Delivery Conditon

, 20-50%,,,:48.75-50.1V
Approx. 20-50% charged Shipment voltage: 48.75-50.1V

Products

Battery Pack for storage

You Might Also Like

FDA Approved Lemborexant Sleep-Wake Disorders and Insomnia D......

Dmr Digital Two-Way Radio, UHF/VHF, Compatible with Mototrbo......

Multifunctional Shr Opt/RF Hair Removel Elight Birth Mark Re......

Air Lift D2300 2300lbs Rubber Air Spring Bag for Car Truck A......

Hot Feed Rubber Extruder with Ce

Single Girder Gantry Crane with Factory Price

D2w6y Cheap Manual Home Used ABS Crank Hospital Foldaway Bed

Old Style Wooden Treasure Box with Brass Latch Woodcraft

Arena PARA Gatos for Toilet Bentonite Cat Sand Pet Supply

Women A Line Short Knee Length Tutu Tulle Prom Party Skirt

G Single Screw Progressive Cavity Pump Self-Priming Slurry P......

700ml Round Shape Spirits Vodka Whisky Brandy Glass Bottle