Products

ASTM/Asme A335/SA335 P1, P2, P5, P9, P11, P22, P23, P91, P92 Seamless Alloy Steel Pipe

China ASTM/Asme A335/SA335 P1, P2, P5, P9, P11, P22, P23, P91, P92 Seamless Alloy Steel Pipe, Find details about China A335 P11 Steel Pipes, A335 P11 Steel Tubes from ASTM/Asme A335/SA335 P1, P2, P5, P9, P11, P22, P23, P91, P92 Seamless Alloy Steel Pipe

Model NO.
ASTM/ASME A335/SA335 P1,P2,P5,P9,P11,P22,P23,P91
Trademark
C&N
Origin
China
Model NO.
ASTM/ASME A335/SA335 P1,P2,P5,P9,P11,P22,P23,P91
Trademark
C&N
Origin
China
Description: Alloy steel pipe, alloy seamless steel pipe, alloy welded pipe,seamless alloy steel pipe,alloy pipe,alloy steel tube 
  
Standard:ASTM A335,JIS G3458,JIS A3462,DIN17175,GB5310,GB9948 
ASTM/AME  A335 P1/P5/P9/P11/P12/P22/ P91/P92 Seamless Ferritic Alloy-Steel Pipe for High-Temperature Service 
Material:ASTM A335 P2, ASTM A335 P12, ASTM A335 P11, ASTM A335 P22, ASTM A335 P5, ASTM A335 P91, ASTM A335 P92. 
Outside Diameter:6 mm~600mm 
Wall thickness:2mm~60mm 

 

 

Chemical Composition(%):

Grade		UNS DesignationComposition, %
CarbonManganesePhosphorus,SulfurSiliconChromiumMolybdenumOthers
P1K115220.10-0.200.30-0.800.025 max0.025 max0.10-0.50---0.44-0.65---
P2K115470.10-0.200.30-0.610.025 max0.025 max0.10-0.300.50-0.810.44-0.65---
P5K415450.15 max0.30-0.600.025 max0.025 max0.50 max4.00-6.000.45-0.65---
P9S504000.15 max0.30-0.600.025 max0.025 max0.25-1.008.00-10.000.90-1.10---
P11K115970.05-0.150.30-0.600.025 max0.025 max0.50-1.001.00-1.500.44-0.65---
P12K115620.05-0.150.30-0.610.025 max0.025 max0.50 max0.80-1.250.44-0.65---
P15K115780.05-0.150.30-0.600.025 max0.025 max 1.15-1.65---0.44-0.65---
P21K315450.05-0.150.30-0.600.025 max0.025 max0.50 max2.65-3.350.80-1.06---
P22K215900.05-0.150.30-0.600.025 max0.025 max0.50 max1.90-2.600.87-1.13---
P23K416500.04-0.100.10-0.600.030.010.50 max1.90-2.600.05-0.30V 0.20-0.30
Cb 0.02-0.08
B 0.0005-0.006
N 0.030 max
Al 0.030 max
W 1.45-1.75
P91K915600.08-0.120.30-0.600.020.010.20-0.508.00-9.500.85-1.05V 0.18-0.25
N 0.030-0.070
Ni 0.40 max
Al 0.04 max
Cb 0.06-0.10
P92K924600.07-0.130.30-0.600.020.010.50 max8.50-9.500.30-0.60V 0.15-0.25
N 0.03-0.07
Ni 0.40 max
Al 0.04 max
Cb 0.04-0.09
W 1.5-2.00
B 0.001-0.006

Mechanical Properties

Data
Grade P11, P22, P5, P9
Grade P91
Grade P92

Tensile strength, min, (MPa)
415
585
620

Yield strength, min, (MPa)
205
415
440

Elongation, min, (%), L/T
30/20
20/
20/

 

Heat Treatment
A / N+T
N+T / Q+T
N+T

Material & Manufacture
Pipe may be either hot finished or cold drawn with the finishing heat treatment noted below.
Heat Treatment Requirements

Grade
Heat Treatment Type 
P5, P9, P11, and P22
Normalizing Temperature Range F [C]
Subcritical Annealing or Tempering 
Temperature Range F [C]

P5 (b,c)
Full or Isothermal Anneal
 
 

 
Normalize and Temper
*****
1250 [675]

 
Subcritical Anneal (P5c only)
*****
1325 - 1375 [715 - 745]

P9
Full or Isothermal Anneal
 
 

 
Normalize and Temper
*****
1250 [675]

P11
Full or Isothermal Anneal
 
 

 
Normalize and Temper
*****
1200 [650]

P22
Full or Isothermal Anneal
 
 

 
Normalize and Temper
*****
1250 [675]

P91
Normalize and Temper
1900-1975 [1040 - 1080]
1350-1470 [730 - 800]

 
Quench and Temper
1900-1975 [1040 - 1080]
1350-1470 [730 - 800]

 
Mechanical Tests Specified
Transverse or Longitudinal Tension Test and Flattening Test, Hardness Test, or Bend Test 
For material heat treated in a batch-type furnace, tests shall be made on 5% of the pipe from each treated lot. For small lots, at least one pipe shall be tested. 
For material heat treated by the continuous process, tests shall be made on a sufficient number of pipe to constitute 5% of the lot, but in no case less than 2 pipe.
Notes for Hardness Test: 
P91 shall not have a hardness not exceeding 250 HB/265 HV [25HRC].
Notes for Bend Test: 
For pipe whose diameter exceeds NPS 25 and whose diameter to wall thickness ratio is 7.0 or less shall be subjected to the bend test instead of the flattening test. 
Other pipe whose diameter equals or exceeds NPS 10 may be given the bend test in place of the flattening test subject to the approval of the purchaser. 
The bend test specimens shall be bent at room temperature through 180 without cracking on the outside of the bent portion.
Hydrostatic Test
The inside diameter of the bend shall be 1 inch [25 mm]. 
Each length of pipe shall be Hydro tested, at option of manufacture nondestructive electric testing can be used.

You Might Also Like