Cable Stripper
China Cable Stripper, Find details about China Cable Waste Stripper, Cable Stripping Machine from Cable Stripper
Basic Info.
Model NO.
HSNQ18KO
Trademark
HSN
Origin
China
HS Code
8479909090
Model NO.
HSNQ18KO
Trademark
HSN
Origin
China
HS Code
8479909090
Product Desciption
Cable Stripping Machine
HSNQ18KO Cable Stripping Machine
Brief Introduction
The machine is for peeling off cable the outsourced plastic fore skin and metal core wire, because the cable diameter has different sizes and wire material and composition are not same, different cable should be used different suitable models. In the waste recycling industry, this machine makes operating system, save time and effort to more efficiently complete the recycling of waste wire and cable.
We have different capacity machine for you choose. And we also offer customized service.
Main Features
Simple Structure, Easy operation.
Safe production, Less electric cost.
Technical Specifications
Instructions for use
1. Before working, please check whether the machine operating is normal, feed according to the size of the cable diameter, in turn into the corresponding feed hole.
2. In order to extend durability of the blade, when feeding should be cut off connector of rubber cable, so as not to break the blade gap.
3. If the output cable occurrence of too deep and broken wire problem, pay attention to the following situation:
a) should adjust the feed gear, that is the two sides of the spring pressure.
b) when feeding, please check whether misplace the cable position of the feeding hole.
c) if the blade is new changed, whether the edge is too sharp application grinding stone slightly trim, moderate so far.
4. If output cable, the outer skin has been peeled off, but copper wire can't be exposed. There are mainly the following:
a) spring pressure is too loose, the pressure should be tightened;
b) the upper shaft rolling too deep, please use grinding stone to polish the upper shaft, but avoid to be over-polished, too much grinding easy to cause oily cable lines difficult to drive;
c) the wire diameter is small, or the upper and lower shaft gap is more, appropriate adjustment of the two-axis gap;
d) the processed cable has been hot, copper wire will not be easy to expose to the skin.
5. If after feeding, the crushing gear can not transmission the cable, the material stays in the middle, there are several situations:
a) check each belt if looseness;
b) check whether the spring pressure on both sides of each gear is too tight, there is no force, should relax the pressure;
c) cable oily too much, so that the two axes slip, should always clean the two axes.
Instructions for use:
HSNQ18KO Cable Stripping Machine
Brief Introduction
The machine is for peeling off cable the outsourced plastic fore skin and metal core wire, because the cable diameter has different sizes and wire material and composition are not same, different cable should be used different suitable models. In the waste recycling industry, this machine makes operating system, save time and effort to more efficiently complete the recycling of waste wire and cable.
We have different capacity machine for you choose. And we also offer customized service.
Main Features
Simple Structure, Easy operation.
Safe production, Less electric cost.
Technical Specifications
| Model | Power | Voltage | Cable Range | Blades | Hole | Output | Size | Weight |
| HSNQ18KOF | 3.0kw | 220V/380V | 1-50mm | 19 | 2+2+11 | 30m per minute | 70x61 x84cm | 110kg |
| HSNQ18KOB | 2.2kw | 220V/380V | 1-42mm | 23+5 | 1+5+5+10 | 30m per minute | 70x61 x84cm | 110kg |
Instructions for use
1. Before working, please check whether the machine operating is normal, feed according to the size of the cable diameter, in turn into the corresponding feed hole.
2. In order to extend durability of the blade, when feeding should be cut off connector of rubber cable, so as not to break the blade gap.
3. If the output cable occurrence of too deep and broken wire problem, pay attention to the following situation:
a) should adjust the feed gear, that is the two sides of the spring pressure.
b) when feeding, please check whether misplace the cable position of the feeding hole.
c) if the blade is new changed, whether the edge is too sharp application grinding stone slightly trim, moderate so far.
4. If output cable, the outer skin has been peeled off, but copper wire can't be exposed. There are mainly the following:
a) spring pressure is too loose, the pressure should be tightened;
b) the upper shaft rolling too deep, please use grinding stone to polish the upper shaft, but avoid to be over-polished, too much grinding easy to cause oily cable lines difficult to drive;
c) the wire diameter is small, or the upper and lower shaft gap is more, appropriate adjustment of the two-axis gap;
d) the processed cable has been hot, copper wire will not be easy to expose to the skin.
5. If after feeding, the crushing gear can not transmission the cable, the material stays in the middle, there are several situations:
a) check each belt if looseness;
b) check whether the spring pressure on both sides of each gear is too tight, there is no force, should relax the pressure;
c) cable oily too much, so that the two axes slip, should always clean the two axes.
Instructions for use:
You Might Also Like
FDA Approved Lemborexant Sleep-Wake Disorders and Insomnia D......
Dmr Digital Two-Way Radio, UHF/VHF, Compatible with Mototrbo......
Multifunctional Shr Opt/RF Hair Removel Elight Birth Mark Re......
Air Lift D2300 2300lbs Rubber Air Spring Bag for Car Truck A......
Hot Feed Rubber Extruder with Ce
Single Girder Gantry Crane with Factory Price
D2w6y Cheap Manual Home Used ABS Crank Hospital Foldaway Bed
Old Style Wooden Treasure Box with Brass Latch Woodcraft
Arena PARA Gatos for Toilet Bentonite Cat Sand Pet Supply
Women A Line Short Knee Length Tutu Tulle Prom Party Skirt
G Single Screw Progressive Cavity Pump Self-Priming Slurry P......
700ml Round Shape Spirits Vodka Whisky Brandy Glass Bottle