Products

High Temperature Resistance Rigid PU Foam for Pipe Injection Insulation

China High Temperature Resistance Rigid PU Foam for Pipe Injection Insulation, Find details about China Polyether Polyol, PU Foam from High Temperature Resistance Rigid PU Foam for Pipe Injection Insulation

Model NO.
SDB10D
Viscosity
300
Appearance
Liquid
Shelf Life
6 Months
Water Absorption
3
Gel Time
100-120s
Rise Time
160-200
Physical Properities
35~46kg/M3
Compressive Strength
200~300kpa
Application
Building
Package
Drum
Product Name
High Foaming Quality Blend Polyol Mdi for Pipeline
Type
Synthesis Material Intermediates
Trademark
Shunda
Transport Package
220kg/Drum
Specification
Two components
Origin
China
HS Code
39072090
Model NO.
SDB10D
Viscosity
300
Appearance
Liquid
Shelf Life
6 Months
Water Absorption
3
Gel Time
100-120s
Rise Time
160-200
Physical Properities
35~46kg/M3
Compressive Strength
200~300kpa
Application
Building
Package
Drum
Product Name
High Foaming Quality Blend Polyol Mdi for Pipeline
Type
Synthesis Material Intermediates
Trademark
Shunda
Transport Package
220kg/Drum
Specification
Two components
Origin
China
HS Code
39072090
BLEND POLYOL SDb10d
RIGID PU FOAM FOR PIPE INJECTION INSULATION

High Temperature Resistance Rigid PU Foam for Pipe Injection InsulationPRODUCT INTRODUCTION
sdb10d is a kind of blend polyol used for pipe insulation system for city heating or cooling. When it combined with isocyanate(PM200) leads to the formation of rigid polyurethane foam by using PU injection foam equipment .The foam formed has the characteristics as following:
  1. The thermal conductivity is low, which can meets the requirements of city heating and energy saving.
  2. Service life of the foam is very long, over 30 years.
  3. High temperature resistance and good dimensional stability of the foam, the highest temperature range is 140 ºC.
TYPICAL PHYSICAL PROPERTIES
Physical ProperitiesTest MethodMetricValue
Core DensityGB/T 6343-2009kg/m3≥60
Radial Compressive StrengthGB/T 8813-2008MPa≥0.3
Initial Thermal Conductivity(50°C)GB/T 10294-2008W/(m·K)≤0.033
Close Cell ContentGB/T 10799-2008%≥88
Water AbsorptionGB/T 8810-2005%≤10
Air BubblesGB/T 29047mm1/3Insulation thickness.
Average Cell Size.GB/T 29047mm≤0.5
Importance: The above mentioned are typical test values, and the specific data may vary slightly due to environmental conditions. For our products, the data are not legally binding.
STORAGE RECOMMENDATIONS:
The blend polyol should be stored in the sealed container to avoid the absorption of water vapor. During the transportation, it should avoid serious shake and strong sunlight. It should be stored in ventilated place, avoiding light, water and fire.
Recommended storage temperature: 15~25ºC.
Shelf life: 12 months

.

SAFETY PRECAUTIONS:
Direct contact with SD2102 type blend polyol can lead to moderate eye irritation and mild skin irritation, which can cause skin allergies. Repeated inhalation of high concentration of volatile gas will cause respiratory allergy, and should be treated immediately. Anti- inflammatory and anti-allergic treatment measures should be taken.
Please be careful in the operation to prevent contact with the skin and splash into the eye, please wear the necessary protective equipment (gloves, protective goggles, working clothes, etc.).
Once splashed on the skin or the eye, rinse with water immediately for at least 15 minutes, and the skin is washed with soapy water. Please seek medical treatment immediately after swallowed.
                                                                                       
Notice: This product specification is intended to be used by Shunda Polyurethane Company in order to show sincerity to our customers, while it is not covered by law as a guarantee. Customers can adjust according to the actual operating conditions. If you have any questions, please call our company and we will serve you wholeheartedly.




High Temperature Resistance Rigid PU Foam for Pipe Injection Insulation
High Temperature Resistance Rigid PU Foam for Pipe Injection Insulation
Shunda Company founded in year 1996, is a leading manufacturer of rigid PU foam blend polyol System material, our annual sales reached 50,000 MT in the past three years. We have four
Manufacturer plants in Yantai, Linyi, Dalian and Chang chun with totally more than 400 employees by now. For over 20 years development, Yantai Shunda Polyurethane Co., Ltd has grown up into a modern joint-stock enterprise, which has the research, development, production and operation for the series of rigid polyurethane foam production. We are also the largest global distributor of MDI series of Wanhua Chemical. Depending on our own strong R&D capability, professional purchasing team, quality control ability and full MDI series product supply, we could supply all series of PU raw material to the internal and abroad customers and undertake the
engineering of the insulation project.

Yantai Sanjiang Chemical Industry Materials Co., Ltd is established in 2010 by Shunda Group as its
International sale company, its mainly engaged in Blend polyol, Polyetherpolyol, flameretardants, PU catalysts, Polymeric MDI and other raw materials which are widely used for the insulation of wall and roof building, coldstorage, ship, sandwichpanel, refrigerators, freezers, pipelines, garage door and etc.

High Temperature Resistance Rigid PU Foam for Pipe Injection Insulation
High Temperature Resistance Rigid PU Foam for Pipe Injection Insulation
High Temperature Resistance Rigid PU Foam for Pipe Injection Insulation

Other unmentioned matters and TDS&MSDS.Please visit our official website shundapu.en.made-in-china.com
Or please contact us for information:
 
 

You Might Also Like