China 3000rpm 1500W AC Servo Motor and Servo Driver Servo Driver Zuba, Find details about China Servo Driver Zuba, Drive Servo Blum from 3000rpm 1500W AC Servo Motor and Servo Driver Servo Driver Zuba
Item | Specifications | |||||||||
Model Type MZ630PSI | 1R6 | 2R8 | 5R5 | 7R6 | 012 | 018 | ||||
Outlook | Applicable motor | 200W | 400W | 750W | 0.8-1kW | 1.5kw | 2-3kW | |||
W(mm) | 42 | 56 | 65 | |||||||
H(mm) | 160 | 160 | 160 | |||||||
D(mm) | 148 | 148 | 185 | |||||||
Weight(kg) | 0.8 | 1.0 | 1.5 | |||||||
Input Power | Single phase AC200V-240V,-15%~10%,50/60Hz or three phase AC200V-240V,-15%~10%,50/60Hz | three phase AC200V-240V, -15%~10%,50/60Hz | ||||||||
Model Type MZ630PTI | 8R4 | 012 | 017 | 021 | 026 | |||||
outlook | Applicable motor | 2kW | 3kW | 4.5kW | 5.5kW | 7.5kW | ||||
W(mm) | 110 | |||||||||
H(mm) | 222 | |||||||||
D(mm) | 200.80 | |||||||||
Weight(kg) | 4.0 | |||||||||
Input Power | three phase AC380V-440V,-15%~10%,50/60Hz | |||||||||
Specification | Environment | ºC | Use environment humidity | 0~55ºC | ||||||
Storage environment humidity | -20~65ºC | |||||||||
Humidity | Use environment humidity | 20~85% RH below(No condensation) | ||||||||
Storage environment humidity | 20~85% RH below(No condensation) | |||||||||
Use to preserve ambient air | indoor(no sunshine),No corrosive gas, flammable gas, oil mist, dust | |||||||||
altitude | Below 1000m | |||||||||
vibration | 5.8m/s2(0.6G)below 10~60Hz(Can not be used continuously at resonance frequency) | |||||||||
Insulation withstand voltage | Basic-FG between AC1500V 1min | |||||||||
Control way | Three-phase PWM converter sine wave drive | |||||||||
Encoder feedback | 1: Provincial line 2500 line 2: 17bit (after adding a battery, it can be used as a multi-turn absolute encoder) | |||||||||
Control signal | Input | 9 inputs (DC24V optocoupler isolation) switch according to the control mode function | ||||||||
Output | 5 output (DC24V optocoupler isolation, open collector output) switch according to the control mode function | |||||||||
Pulse signal | Input | 2 inputs (optocoupler isolation, RS-422 differential, open collector output) | ||||||||
Output | 4 outputs (A/B/Z phase RS-422 differential; Z phase open collector output) | |||||||||
Communication function | RS232 | For PC communication (for "Servostudio" connection) | ||||||||
RS-485 | For upper remote control communication (1:n) | |||||||||
CAN | CANOPEN bus communication | |||||||||
Regeneration function | Optional regenerative resistor, external regenerative resistor. Pay attention to modify internal parameters | |||||||||
Dynamic brake | YES | |||||||||
Control model | 6 control modes: speed control, position control, torque control, torque/speed control, speed/position control, torque/position, torque/speed/position hybrid control | |||||||||
Function | Control input | Alarm reset, proportional action switching, zero fixed function enable, forward drive prohibited, reverse drive prohibited, external torque limit for forward rotation, external torque limit for reverse rotation, forward jog, reverse jog, forward Reset switch, reverse reset switch, origin switch, emergency stop, servo enable, gain switch | ||||||||
Control output | Servo ready, motor rotating, zero speed signal, speed reached, position reached, positioning approach signal, torque limit, speed limit, brake output, warning, servo failure, alarm code (3-digit output) | |||||||||
Position control | Pulse input | Maximum command pulse frequency | Differential input: high-speed maximum 4Mpps, pulse width cannot be less than 0.125μs The maximum low speed is 500Kpps, and the pulse width cannot be less than 1μs Open collector: maximum 200Kpps, pulse width cannot be less than 2.5μs | |||||||
Input pulse signal form | Differential input; open collector | |||||||||
Input pulse signal method | Pulse + direction, right angle phase difference (A phase + B phase), CW + CCW pulse | |||||||||
Command pulse division/multiplication (Electronic gear ratio setting) | 0.1048576 < B/A <419430.4 | |||||||||
Command filter | Smoothing filter, FIR filter | |||||||||
Pulse output | Output pulse form | Phase A, Phase B: Differential output Z phase: differential output or open collector output | ||||||||
Frequency division ratio | Arbitrary frequency division | |||||||||
Output pulse function | Encoder position pulse and position pulse command (can be set) | |||||||||
Speed control | Control input | Servo ON, alarm reset, speed command reverse, zero speed clamp, internal command selection input 1, internal command selection input 2, internal command selection input 3, internal command selection input 4, forward rotation external torque limit input, reverse rotation External torque limit input, emergency stop | ||||||||
Control output | Alarm status, servo preparation, brake release, torque limit output, speed limit output speed reached, speed consistent, motor rotation output, zero-speed signal output | |||||||||
Torque Control | Control input | Servo ON, alarm reset, torque command reverse, zero speed clamp | ||||||||
Control output | Alarm status, servo preparation, brake release, torque limit, speed limit output, emergency stop | |||||||||
Torque command input | (Factory default setting, the range can be set by function code) | |||||||||
Speed limit function | Positive and negative internal speed limit P03.27, P03.28 | |||||||||
Common | Speed observer function | YES | ||||||||
Damping control function | YES | |||||||||
Adaptive notch filter | YES | |||||||||
Automatic adjustment function | YES | |||||||||
Encoder output frequency division | YES | |||||||||
Internal location planning function | YES | |||||||||
Adjustment/ function setting | Use the host computer setting software "Servostudio" to adjust | |||||||||
Protection | Over voltage, abnormal power supply, overcurrent, overload, abnormal encoder, overspeed, excessive position deviation, abnormal parameters, etc. |