GM13 Smooth and Texture Side 1.5mm HDPE Geomembrane for Landfill
China GM13 Smooth and Texture Side 1.5mm HDPE Geomembrane for Landfill, Find details about China HDPE Geomembrane, 1.5mm HDPE Geomembrane from GM13 Smooth and Texture Side 1.5mm HDPE Geomembrane for Landfill
Basic Info.
Model NO.
ASTM GRI-GM 13
Length
50-100m/ as Your Request
Width
1-8m/ as Your Request
MOQ
5000 M2
Standard
ASTM Gri-GM13
Sample
Freely
Keyward
GM13 Smooth and Texture Side 1.5mm HDPE Geomembran
Trademark
Dajin
Transport Package
PP Bags
Specification
0.2-3mm
Origin
China
HS Code
3920109090
Model NO.
ASTM GRI-GM 13
Length
50-100m/ as Your Request
Width
1-8m/ as Your Request
MOQ
5000 M2
Standard
ASTM Gri-GM13
Sample
Freely
Keyward
GM13 Smooth and Texture Side 1.5mm HDPE Geomembran
Trademark
Dajin
Transport Package
PP Bags
Specification
0.2-3mm
Origin
China
HS Code
3920109090
Product Desciption
GM13 Smooth and Texture Side Landfill Liner 1.5mm HDPE Geomembrane
Product description
Erosion Control
Our geomembranes offer effective erosion control. The liner eliminates slope deterioration caused by
surface rains, wave action, and wind. The liner prevents eroded materials from filling the pond and
reducing the volume. In addition, costly erosion repair and dredging are eliminated. Dajin's high-quality
HDPE geomembranes offer secure water containment, enhanced quality control, erosion control, and
improved crop quality, and they are kind to the environment.
Geomembrane is a very low permeability synthetic membrane liner or barrier used with any geotechnical
engineering related material so as to control fluid (or gas) migration in a human-made project, structure,
or system. Geomembranes are made from relatively thin continuous polymeric sheets, but they can also
be made from the impregnation of geotextiles with asphalt, elastomer or polymer sprays, or as multilayered
bitumen geocomposites. Continuous polymer sheet geomembranes are, by far, the most common
Landfill project
First of all, make preparations to clean, roll and flatten the surface of the base layer to be laid; then take
the materials locally and fill the surface of the base layer with an excavator. The filled layer is not less than
30 cm thick and there is no loess If you want, you can use yellow sand or fine sand instead, fill up the soil
layer or sand layer, compact the soil protection layer, prepare for the next step, dig underground water to
guide the drainage, and distribute the drainage pipes.
Secondly, the soil protection base layer should be leveled and tamped, and the surface should be smooth
and smooth, and there should be no gravel over 2cm or obvious small pits; after checking that there is no
problem, the bentonite waterproof blanket will be naturally relaxed and flat Lay on the soil protection layer
with the non-woven fabric facing down and the woven fabric facing up. Note: The construction of bentonite
waterproof blanket should be carried out in rainless and snowy weather. In case of rain and snow, the plastic
film should be used to prevent the swelling of the bentonite in the waterproof blanket. The overlap of the
bentonite waterproof blanket is not less than 20 cm. Sprinkle bentonite lap powder evenly on the lap edge,
spray it to make it compact after pressing, and keep it flat. After laying, check the waterproof blanket for
damage and holes, repair it in time, and prepare for the next step.
In the 1980s, HDPE high-density polyethylene geomembrane, also called HDPE anti-seepage geomembrane,
also called the anti-seepage membrane, was used in anti-seepage projects in landfills. With China's emphasis
on ecological environment and the increasing awareness of national environmental protection, anti-seepage
membranes are widely used in landfill disposal. Lay the HDPE impermeable membrane on the bentonite
waterproof blanket, stretch it flat, without large air bubbles, flatten it, and avoid heavy machinery such as
excavators rolling, turning or walking on the impermeable membrane; impermeable membrane and
anti-impermeable membrane The lapped edge of the membrane should be no less than ten centimeters,
and the edge should be kept clean and free of debris and stones; then prepare for welding. Before welding,
take two pieces of geomembrane of about one meter for test welding, adjust the reasonable temperature
of the welding machine, and then use a professional Welding personnel welding; welding should be carried
out simultaneously with the laying of the impermeable membrane until the laying is completed. Note: During the
laying of the geomembrane, the excavator will cover the geomembrane slowly and evenly with soil on the side.
Welding and filling are carried out simultaneously to avoid artificial damage to the geomembrane; the protective
soil layer on the geomembrane is not lower than Thirty centimeters thick to prevent plant roots from piercing
the geomembrane, and then the soil is compacted.
Manufacturing Technique
HDPE Geomembrane liner are made from polyethylene polymer materials by the film-blowing
process.it is most widelyused for solid waste containment (such as landfill liners), mining and
water containment applications.
Item
Main Features:
1.Waterproof and impermeable
2.UV resistance
3.High tearing resistance
4. Puncture-resisting
5.Nontoxic,non-tasteness. Long life:over 100 years underground without sunlight.
Packaging & Shipping
The geomembrane roll are in the hand sewing woven bag packing, safe and scratch-proof. The
bag color can becustomized, with your own logo.
Application
1.Various waterproof and anti-seepage projects such as landfills, solid waste treatment stations,
tailings storage yards
2.sewage ponds, petrochemicals, construction, water conservancy, mining, landscape gardens,
subway tunnels, aquaculture, livestock biogas digesters, etc.
3.Environmental protection projects:Landfill,sewage treatment plants,power plant regulating pools,
industrial and hospital solid wastes,etc.
4.Mining:heap leaching platforms, conduit and retention channels and wells for liquid solutions,
final disposal reservoirs.
Index
Related products
Company introduction
Shandong Dajin Geosynthetics Co.,LTD is a comprehensive geosynthetic service provider
as well as solution provider integrating Engineering design, manufacturing, installation, guarantee
in the Seepage control industry. The products provided by Dajin include geotextile, geomembrane,
composite geomembrane warp-knitted geogrid,glass fiber geogrid, plastic geogrid, steel-plastic
geogrid, mining geogrid, high-strength mining polyester fiber mesh,geocell and other geosynthetics.
Our goal is to become a world-class company dedicated to providing our customers with
comprehensive, reliable and high-quality services and solutions. Meeting the needs of people to
increase their quality of life, promoting the smart use of the planet's resources.
Design
The Dajin engineering team can provide solid advice on all types of Seepage control insustry,
as well as their correct design for projects, including construction details and advice on the
the general configuration of the project.
Documentation
Each roll of Dajin geomembrane has its own identification number. The identification number is
traceable in line with the quality control plan. Dajin can add the necessary documentation or
modify the packing for countries and territories with special product certification requirements.
Quality plan
The Dajin quality plan is designed to provide customers with the highest standards of product control
and reduce our product returns rate tozero. The checklist covers a wide range of aspects, from the
quality of the raw material all the way through to the roll labels.
Installation
Upon request by the customer, Dajin can also offer a full turnkey installation service, covering
the materials manufactured by Dajin, any other geosynthetics products, installation and all
additional materials required to fully complete the project. We can supply supervisors and
installers, with or without welding equipment, such as machines and tools, to manage a
group of local staff supplied by the customer. We can also provide training courses to staff
provided by the customer.
Guarantee
Dajin provides a 10-year guarantee on all manufactured geomembranes. Based on our
experience, the useful life of a jin's high-performance products under almost any normal
conditions of service can be measured in decades and is probably over 100 years.
FAQ
Q: Are you a trading company or manufacturer?
We are a factory.
Q: Is the quality of your products stable?
The company has a complete QC system, and each batch of products will be sampled and the
samples will be kept for 5 years.
Q: Can you do OEM?
Yes, of course. We can produce the products as your request.
Q: Do you provide samples ? is it free?
Yes, we could offer the sample for free charge but do not pay the cost of freight.
Q: How long is your delivery time?
Generally, it is 5-10 days if the goods are in stock. or it is 10-15 days if the goods are not in stock,
it is according to quantity.
Q: What is your terms of payment?
Payment<=5000USD, 100% in advance. Payment>=5000USD, 30% T/T in advance,balance
before shipment.
If you have another question, please feel free to contact us at any time.
Product description
Erosion Control
Our geomembranes offer effective erosion control. The liner eliminates slope deterioration caused by
surface rains, wave action, and wind. The liner prevents eroded materials from filling the pond and
reducing the volume. In addition, costly erosion repair and dredging are eliminated. Dajin's high-quality
HDPE geomembranes offer secure water containment, enhanced quality control, erosion control, and
improved crop quality, and they are kind to the environment.
Geomembrane is a very low permeability synthetic membrane liner or barrier used with any geotechnical
engineering related material so as to control fluid (or gas) migration in a human-made project, structure,
or system. Geomembranes are made from relatively thin continuous polymeric sheets, but they can also
be made from the impregnation of geotextiles with asphalt, elastomer or polymer sprays, or as multilayered
bitumen geocomposites. Continuous polymer sheet geomembranes are, by far, the most common
Landfill project
First of all, make preparations to clean, roll and flatten the surface of the base layer to be laid; then take
the materials locally and fill the surface of the base layer with an excavator. The filled layer is not less than
30 cm thick and there is no loess If you want, you can use yellow sand or fine sand instead, fill up the soil
layer or sand layer, compact the soil protection layer, prepare for the next step, dig underground water to
guide the drainage, and distribute the drainage pipes.
Secondly, the soil protection base layer should be leveled and tamped, and the surface should be smooth
and smooth, and there should be no gravel over 2cm or obvious small pits; after checking that there is no
problem, the bentonite waterproof blanket will be naturally relaxed and flat Lay on the soil protection layer
with the non-woven fabric facing down and the woven fabric facing up. Note: The construction of bentonite
waterproof blanket should be carried out in rainless and snowy weather. In case of rain and snow, the plastic
film should be used to prevent the swelling of the bentonite in the waterproof blanket. The overlap of the
bentonite waterproof blanket is not less than 20 cm. Sprinkle bentonite lap powder evenly on the lap edge,
spray it to make it compact after pressing, and keep it flat. After laying, check the waterproof blanket for
damage and holes, repair it in time, and prepare for the next step.
In the 1980s, HDPE high-density polyethylene geomembrane, also called HDPE anti-seepage geomembrane,
also called the anti-seepage membrane, was used in anti-seepage projects in landfills. With China's emphasis
on ecological environment and the increasing awareness of national environmental protection, anti-seepage
membranes are widely used in landfill disposal. Lay the HDPE impermeable membrane on the bentonite
waterproof blanket, stretch it flat, without large air bubbles, flatten it, and avoid heavy machinery such as
excavators rolling, turning or walking on the impermeable membrane; impermeable membrane and
anti-impermeable membrane The lapped edge of the membrane should be no less than ten centimeters,
and the edge should be kept clean and free of debris and stones; then prepare for welding. Before welding,
take two pieces of geomembrane of about one meter for test welding, adjust the reasonable temperature
of the welding machine, and then use a professional Welding personnel welding; welding should be carried
out simultaneously with the laying of the impermeable membrane until the laying is completed. Note: During the
laying of the geomembrane, the excavator will cover the geomembrane slowly and evenly with soil on the side.
Welding and filling are carried out simultaneously to avoid artificial damage to the geomembrane; the protective
soil layer on the geomembrane is not lower than Thirty centimeters thick to prevent plant roots from piercing
the geomembrane, and then the soil is compacted.
Manufacturing Technique
HDPE Geomembrane liner are made from polyethylene polymer materials by the film-blowing
process.it is most widelyused for solid waste containment (such as landfill liners), mining and
water containment applications.
Item
| Product Name: | HDPE Geomembrane |
| Thickness: | 0.2mm-3.0mm(Main:0.5mm, 0.75mm,1.0mm,1.5mm,2.0mm) |
| Length : | 50m/roll,100m/roll,150m/roll or follow your request |
| width: | 1m-8m or follow customers' demand, Main width is 4m,5m,5.8m,6.0m |
| Surface | Both side smooth/both side textured one side textured one side smooth, or as your request |
| Color: | White,Black,Green,Blue,mainly black |
| Material: | HDPE,LDPE,LLDPE, ( 100% Virgin) |
| Certification: | ISO9001:2008, |
| Standard: | ASTM GRI-GM13 |
Main Features:
1.Waterproof and impermeable
2.UV resistance
3.High tearing resistance
4. Puncture-resisting
5.Nontoxic,non-tasteness. Long life:over 100 years underground without sunlight.
Packaging & Shipping
The geomembrane roll are in the hand sewing woven bag packing, safe and scratch-proof. The
bag color can becustomized, with your own logo.
Application
1.Various waterproof and anti-seepage projects such as landfills, solid waste treatment stations,
tailings storage yards
2.sewage ponds, petrochemicals, construction, water conservancy, mining, landscape gardens,
subway tunnels, aquaculture, livestock biogas digesters, etc.
3.Environmental protection projects:Landfill,sewage treatment plants,power plant regulating pools,
industrial and hospital solid wastes,etc.
4.Mining:heap leaching platforms, conduit and retention channels and wells for liquid solutions,
final disposal reservoirs.
Index
| S/N | Item | Index | ||||||
| Thickness mm | 0.75 | 1.00 | 1.25 | 1.50 | 2.00 | 2.50 | 3.00 | |
| 1 | Density g/cm3 | ≥0.940 | ||||||
| 2 | Tensile yield strength (vertical and horizontal) N/mm | ≥11 | ≥15 | ≥18 | ≥22 | ≥29 | ≥37 | ≥44 |
| 3 | Tensile breaking strength (vertical and horizontal) N/mm | ≥20 | ≥27 | ≥33 | ≥40 | ≥53 | ≥67 | ≥80 |
| 4 | Elongation (vertical and horizontal) % | - | - | - | ≥12 | |||
| 5 | Elongation at break (vertical and horizontal) % | ≥700 | ||||||
| 6 | Tearing load at right angle (vertical and horizontal) N | ≥93 | ≥125 | ≥160 | ≥190 | ≥250 | ≥315 | ≥375 |
| 7 | Anti-puncture strength N | ≥240 | ≥320 | ≥400 | ≥480 | ≥540 | ≥800 | ≥960 |
| 8 ' | Tensile load stress cracking (tensile method of dead load of the cut) h | _ | ≥300 | |||||
| 9 | Carbon black content % | 2.0~3.0 | ||||||
| 10 | Carbon black dispersion | The number of Level 3 among 10 data is not more than one; Level 4 and Level 5 are not allowed. | ||||||
| Oxidation induction time (OIT) min | Oxidation induction time under normal pressure ≥100 | |||||||
| 11* | Oxidation induction time under disjoining pressure ≥400 | |||||||
| 12 | 85°C thermal aging (retention rate of OIT under normal pressure after 90d) % | ≥55 | ||||||
| 13a | Ultraviolet resistance (retention rate of OIT after 1600h ultraviolet irradiation) % | ≥50 | ||||||
| Note: Technical performance index of thickness specification not listed in the table shall be implemented according to the interpolation method. | ||||||||
| For two indexes of Item 11 and Item 13, select one from retention rate of OIT under normal pressure and retention rate of OIT under high pressure and carry out the test. | ||||||||
Related products
Company introduction
Shandong Dajin Geosynthetics Co.,LTD is a comprehensive geosynthetic service provider
as well as solution provider integrating Engineering design, manufacturing, installation, guarantee
in the Seepage control industry. The products provided by Dajin include geotextile, geomembrane,
composite geomembrane warp-knitted geogrid,glass fiber geogrid, plastic geogrid, steel-plastic
geogrid, mining geogrid, high-strength mining polyester fiber mesh,geocell and other geosynthetics.
Our goal is to become a world-class company dedicated to providing our customers with
comprehensive, reliable and high-quality services and solutions. Meeting the needs of people to
increase their quality of life, promoting the smart use of the planet's resources.
Design
The Dajin engineering team can provide solid advice on all types of Seepage control insustry,
as well as their correct design for projects, including construction details and advice on the
the general configuration of the project.
Documentation
Each roll of Dajin geomembrane has its own identification number. The identification number is
traceable in line with the quality control plan. Dajin can add the necessary documentation or
modify the packing for countries and territories with special product certification requirements.
Quality plan
The Dajin quality plan is designed to provide customers with the highest standards of product control
and reduce our product returns rate tozero. The checklist covers a wide range of aspects, from the
quality of the raw material all the way through to the roll labels.
Installation
Upon request by the customer, Dajin can also offer a full turnkey installation service, covering
the materials manufactured by Dajin, any other geosynthetics products, installation and all
additional materials required to fully complete the project. We can supply supervisors and
installers, with or without welding equipment, such as machines and tools, to manage a
group of local staff supplied by the customer. We can also provide training courses to staff
provided by the customer.
Guarantee
Dajin provides a 10-year guarantee on all manufactured geomembranes. Based on our
experience, the useful life of a jin's high-performance products under almost any normal
conditions of service can be measured in decades and is probably over 100 years.
FAQ
Q: Are you a trading company or manufacturer?
We are a factory.
Q: Is the quality of your products stable?
The company has a complete QC system, and each batch of products will be sampled and the
samples will be kept for 5 years.
Q: Can you do OEM?
Yes, of course. We can produce the products as your request.
Q: Do you provide samples ? is it free?
Yes, we could offer the sample for free charge but do not pay the cost of freight.
Q: How long is your delivery time?
Generally, it is 5-10 days if the goods are in stock. or it is 10-15 days if the goods are not in stock,
it is according to quantity.
Q: What is your terms of payment?
Payment<=5000USD, 100% in advance. Payment>=5000USD, 30% T/T in advance,balance
before shipment.
If you have another question, please feel free to contact us at any time.
You Might Also Like
ASTM F3125/A325tc Round Head Bolts with 2h Nut and F436 Wash......
OEM/ODM Low MOQ Private Label Natural Organic Skin Lightenin......
Full Automatic Qt4-18 Hydraulic Brick Machine Construction M......
Car Accessory Auto Body Part Front Bumper for D-Max 2006 200......
Milking Parlor Machine for Sale 18 Seats for 100 Cows
Pet Bottle Orange Juice Making Machine/ Bottle Orange Water ......
Wangtong High Security Zinc Alloy Tun Knob Lock Cylinder
Medical Equipment Clinical Infrared Electronic Digital Therm......
PE Synthetic Resin Calcium Oxide Cao Desiccant Masterbatch f......
A1 Energy Star 1150lm R30/PAR30 Bulb/Lamp/Light
Chinese Supplier CNC Machining Part 3ply Earloop Medical Mas......