Oem ODM RX TX HDMI Extender 60m HDMI Extender cat5e x1 with IR Remote Control
Rack Mount 4K DVI Fiber Extender converter16 unit insert cards
This product can extend the full HD HDMI signal to 120 meters with a single cable cable, with no image loss and delay. There are many professional designs for a variety of application scenarios, especially in the engineering field.
Product features:
1 Long distance transmission to 120 meters via a CAT5/5E/6 single network cable
2 Signal lossless compression, low latency
3 Maximum resolution up to 4096*2160/3840*2160@60Hz(4:4:4)
4 Support RS232 two-way return
5 Support IR infrared two-way return
6 HDCP is not supported
7 Support reset function
Technical Parameters:
Power Input | 5V |
Power Consumption | 3W |
HDMI Version | HDMI2 |
HDMI Interface | HDMI A female |
Network Interface | RJ45 |
Link Connection | Cat5e/6 |
Transmission Distance | 120m |
Input Resolution | 480i@60Hz, 480p@60Hz, 576i@50Hz, 576p@50Hz, 720p@50/60Hz, 1080p@50/60Hz, 1080i@50/60Hz, 4Kx2K@24/25/30/60Hz |
Output Resolution | 4Kx2K@60Hz |
Maximum Transmission Rate | 18Gbps |
Infrared Control | 20-60Hz IR return |
Operating Temperature | -20ºC~70ºC |
Stored Temperature | -40ºC~80ºC |
Humidity | 20%~90% RH(no crystal water) |
Packing List
1*HDMI transmitter
1*HDMI receiver
2*DC 5V power supply
1*infrared receiver
1*infrared transmitter
Product pannel:
Connection Diagram:
The 120M HDMI KVM Many to Many Over IP Extender with IR HDMI, USB and IR over a LAN (Local Area Network).
Supports resolution up to 1920*1080P Full HD. Source content can be transmitted from one transmitter to several receivers (Up to 253 receivers) over LAN, and the transmitter can be controlled by either of the receivers in the same LAN over IR or USB keyboard and mouse.
Support resolution up to 1080p Full HDSupport TMDS equalization and enhancement
By transmitting keyboard and mouse Datas via LAN, it is easy to control PC or other media players remotely
Routes up to 16 transmitters to 253 receivers by 1000M IGMP network switch
Support infrared remote control signal pass through
Support Fiber-Optic converter to extend transmission distance up to 20KMPackage Type:
1 * HDMI KVM Extender transmitter
1 * HDMI KVM Extender Receiver
1 * IR transmitter Cable
1 * IR Receiver Cable
2 * DC 5V 1A Power Adapter
1 * Quick-Start Guide
Q: Why the direct one to one connection cannot be used?
A: You must use a super Cat5 / 6e network cable (wire sequence T-568B), please check if the addresses of the DIP switches of the transmitter and receiver match
Q: "Check input signal" appear on the screen? (Check input signal)
A: The input signal is inaccessible, please check if the source of the HDMI input signal is connected normally. It is recommended to replace the shorter HDMI cable. Input signal recommended within 5 meters.
Q: (Searching Tx) appears on the screen?
A: The network cable is partially disconnected, please check if the network cable is normal. It is recommended to use Super
Category 5 and Category 6 network cables.
Connect Diagram
* 1 to 1 connection
Set IP address of the transmitter and receivers to the same
* 1 to Many connections
Set IP address of the transmitter and receivers to the same
* Many to Many connections
By using the IGMP network switch, support up to 16 transmitters (Addr: 0000~1111) in one local area network. Set the receivers' IP address to the same as the transmitter which the receiver wants to connect to.