Products

Megatro 115kv DC PS5 Steel Pole

China Megatro 115kv DC PS5 Steel Pole, Find details about China 115kv DC Steel Tubular Poles (heave angle) , 115kv DC Steel Tubular Poles from Megatro 115kv DC PS5 Steel Pole

Model NO.
MGP-115kv-PS5
Structure
Monopole
We Can Design by Pls & Tower Software
According to Client Desing or Requirement
Trademark
MEGATRO
Transport Package
Export Standard Package
Specification
AS PER CLIENT
Origin
Shandong, China
HS Code
73082000
Model NO.
MGP-115kv-PS5
Structure
Monopole
We Can Design by Pls & Tower Software
According to Client Desing or Requirement
Trademark
MEGATRO
Transport Package
Export Standard Package
Specification
AS PER CLIENT
Origin
Shandong, China
HS Code
73082000
MEGATRO 115KV DC PS5 STEEL POLE


This photo refers to our 115KV DC PS5 STEEL POLE
, which we design and produced for our overseas client over latest three years, it is heavy angle tension tower, with single over head ground wire at top of tower peak.
 
Our 115KV DC PS5 STEEL POLE
technical specification as follow:
1Line details - Circuit (DC) & KV.
technical specification as follow:
1Line details - Circuit (DC) & KV.DC, 132 KV
2Number of phases.3
3Tower design detailsRuling spanWind spanWeight Span
 Tension towers180m200m250m
Heavy angle (°)30-60°
Deflection angle 0-60°
Terminal condition 0-60°
4Conductors Type ( ACSR/AAAC/etc) AAAC Greely Conductor
 Conductor - Single/twin/quad/hexaSingle  
5Earth-wire   Single OPGW (With at least 24 Fiber along with accessories)
6Insulators. Fog type Disc Porcelain Insulators
7Factor of safety.1.5
8Environmental condition of area (Temp).Design Ambient Temperature 40 DegC
9Tower Height.22 Mtr. (Subject to approval )
10Design CodeASCE Manual No -72, IS 802 (part I & part II)-1997, IS 5613 (part I & part II), transmission line manual (publication no -268 )
11Type of Soil (Normal / Black cotton) Yellowish clayey silty fine sand
12Tower data 132 KV D/C Steel Tubular Poles
Shape of poles Circular /Polygonal12 sides
Type of embedded Type/Anchor Base TypeAnchor Base Type
No. of section3
Length of every section 8500mm, 8500mm, 8000mm from bottom to top
Thickness of every section 12mm, 12mm, 10mm from bottom to top
method  of pole sectionsSlip joint
Method of weldingAWS D1:1
Standard of Galvanizing for pole and cross armsASTM A133
 
Standard of galvanizing for bolts , nuts and washersASTM A153
Pole and cross-arm steelQ345B
Base plateQ345B
Fastener (step bolt)Chinese type grade 4.8
Material for anchor boltsChinese steel 45#
 
Remark: above technical data only references for our client, we can design every type for our overseas clients.
 
MEGATRO is a full service engineering company with a global reputation for delivering excellence and innovation in power transmission, transformation, distribution, and telecommunications systems. Our MEGATRO provide and design 115KV DC PS5 STEEL POLES mainly for our overseas client. Since 2004, MEGATRO focus mainly international market and had export many kind of transmission structures to overseas clients. MEGATRO has been manufacturing lattice transmission tower & tapered steel poles for lighting, traffic control, communication and utility applications. MEGATRO pioneered the development of transmission tower, telecom tower, substation, and other steel structure and was also at the forefront in the design of Transmission tower.


Over 10 years of experience and innovation in engineering, designing and building towers has evolved MEGATRO into its current form:
l        Full Turn-Key provider including site acquisition, engineering services, manufacturing,   field services-DAS, tech services, value added reseller and monitoring, maintenance and network ownership
l        Specialize in developing supplying and building wireless and wired networks and in-building telecommunications systems, as well as energy infrastructure
l        Single source from Design to System Integration
l        Top quality, ISO 9001 registered
A complete selection of towers including self-support, lattice steel tower, monopoles and guyed towers, form custom-designed radar towers to broadcast towers and energy infrastructure. MEGATRO carries a variety of related products including fall protection, transmission lines, antennas, obstruction lights, and accessories, and other products if client need, MEGATRO also tailored product as per client condition.
MEGATRO mainly design all kinds of towers and posts for:
a.      Telecoms
b.      Power transmission
c.      TV and Radio Broadcast
d.      Roads and City Development
e.      Wind energy solution
f.        Steel structure and workshop
 
Our complete selection of towers includes:
a.      Self-supporting
b.      Monopoles
c.      Guyed towers
d.      Custom-designed radar towers
e.      Broadcast towers
f.        Power transmission
 
MEGATRO also designs and manufactures tower related products including:
a.      Fall protection
b.      Antenna brackets
c.      Other accessories if needed by clients

Today, with over 10 years of experience and our commitment to excellence, MEGATRO remains an industry leader in the manufacture and design of steel tubular & angular & monopole structures for all Highway, Municipal, Custom, telecom, lighting and electric Utility applications. MEGATRO has a complete staff of professional engineering personnel trained in the PLS Pole program and three different manufacturing processes for producing steel towers, poles and other supports. We utilize the latest versions of PLS-CADD, PLS-POLE, TOWER, AutoCAD and other CAD software.
 
The structure shall be designed according to load combinations given as per IEC 61936-1 and as illustrated below:
Normal loads
1 Dead weight load
2 Tension load
3 Erection load
4 wind load
 
Exceptional loads
1 Switching forces
2 short-circuit forces
3 Loss of conductor tension
4 Earthquake forces


Moreover, MEGATRO is fully equipped and qualified to carry out Design Engineering services which includes:
√ Overhead Transmission line steel tower & Telecom steel tower
   Basic Design and Analysis
√ Shop Erection Drawings
√ As-Built Drawings
 
MEGATRO performs in-house design activities specializing in electrical overhead transmission &telecom tower steel works, which include wind and earthquake loading, static analysis, stress analysis by finite element methods and fatigue. Our Engineering Department is boasting of highly qualified engineering who are conversant with international codes and standards. The work is carried out with extensive use of CAE/CAD via a large of computer network. The computer hardware & drafting software are liked to the CNC workshop equipment for downloading of information thereby eliminating error and saving valuable production time.
 
Besides, MEGATRO is one of the few manufactures who assemble a face of 132KV DC steel tubular poles. This attention to quality may not be the cheapest process but it does insure every tower meets our high standards of quality. And it helps to reduce on-site construction cost due to mismatched assemblies. After fabrication all 132KV DC steel tubular poles are delivered to the galvanizing facility to be Hot DIP Galvanized. Towers are processed through the facility by Caustic Cleaning, Pickling, and then Fluxing. These strict procedures insure years of maintenance free towers. MEGATRO' 132KV DC steel tubular poles systems can accommodate a variety of cross-arm. MEGATRO also offers a wide variety of accessories and mounts.

Fabrication standard: Chinese Standard or other standard which client accepted
A) Dimension and tolerance for angle are according to GB/T1591-1994, similar to EN 10056-1/2
B) Hot dip galvanization in accordance with GB/T 13912-2002, which similar to ASTM A 123
C) The welding will be performance in accordance with AWS D1.1 or CWB standard
D) All fastener galvanization conform to ASTM A153 requirements.

Package: Both parties discuss before delivery
Port of Loading: Qingdao Port
Lead Time: One month or based on the customer's needs ( for time being our capacity about 5000 tons one month, and can meet client requirements)
Minimum order: 1 set


General Fabrication Requirements
Here is general fabrication requirements for our transmission tower; however, both parties must discuss all drawings and confirm all shop drawings, technical specification, and which standard to conform.
Before mass production, we must received all signed approved shop drawings and technical documents from our client.
 
Our Fabrication shall be in strict accordance with detail Drawings prepared by the Contractor and approved by the Engineer.  Fabrication shall begin after the approval of the shop assembly and tests.
      
Shearing
      
Shearing and cutting shall be performed carefully and all portions of the work which will be exposed to view after completion shall be finished neatly.  Manually guided cutting torches shall not be used.
 
All material over 13 (or 12) mm thick shall be cold sawn or machine flame cut.
Cropping or shearing shall be allowed for material thickness of 13 mm or less.
Flame cutting of high yield steel shall be preceded by a slight preheat operation by passing the cutting flame over the part to be cut.
All flame-cut edges shall be ground clean.
      
Bending
 
Bending shall be carried out in such a manner as to avoid indentation and surface damage. All bending over 5o, or high yield steel, shall be performed while the material is hot.
 
Welding
 
No welding shall be done unless prior approval has been obtained from the Engineer.
Welding shall not be allowed at tower attachment points for conductor, shield-wire, insulators or associated assemblies or brackets.
 
Sub-punching
 
All holes in structural steel less than 10 mm thickness may be punched to full size unless otherwise noted on the approved Drawings.  Holes shown on the Drawings as drilled holes and all holes in structural steel 10 mm or more in thickness and tension members of cross-arms shall be drilled or sub-punched and reamed.
 
All holes shall be clean cut and without torn or ragged edges.  All burrs resulting from reaming or drilling shall be removed.  All holes shall be cylindrical and perpendicular to the member.
 
Where necessary to avoid distortion of the holes, holes close to the points of bends shall be made after bending.
 
Punching
 
For punching to full size, the diameter of the punch shall be 1.0 mm larger than the nominal diameter of the bolt, and the diameter of the die shall not be more than 1.5mm larger than the diameter of the punch. For sub-punching, the diameter of the punch shall be 4 mm smaller than the nominal diameter of the bolt, and the diameter of the die shall be not more than 2 mm larger than the diameter of the punch.  Sub-punching for reamed work shall be such that after reaming no punch surface shall appear in the periphery of the hole.
 
Hole Size
 
Where holes are reamed or drilled, the diameter of the finished hole shall be not greater than the nominal diameter of the bolt plus 1.0 mm.
 
 
Accuracy
 
All holes shall be spaced accurately in accordance with the Drawings and shall be located on the gauge lines.
 
The maximum allowable variation in hole spacing from that indicated on the Drawings for all bolt holes shall be 0.8 mm.
 
Fabrication Tolerances
 
A specification for tolerances shall be submitted for approval by the Engineer prior to commencement of fabrication.
 
Bolt List
 
A complete list of bolts showing their lengths and the members, which they are to connect shall be given on the erection diagrams.
 
Locking Devices
 
Locking devices for tower bolts will not be required, but point punching shall be performed.
 
Anti-theft Fasteners
      
Appropriate anti-theft fasteners for example Huck-bolting shall be applied on all the towers up to the level of anti-climbing devices, to prevent theft of tower members.
Piece Marks
 
All pieces shall be stamped before galvanizing with the piece marks shown on the erection Drawings, with the marking not less than 20 mm high placed in the same relative location on all pieces.  The marking shall be plainly visible after galvanizing.
 
Galvanizing
 
All material shall be hot-dip galvanized after fabrication in accordance with the latest revision of GB/T 13912-2002 or ASTM Specification A 123.
 
Material that has been rejected because of bare spots or other coating defects shall either be stripped and re-galvanized, or the uncoated areas shall be recoated by an approved method.
 
All plates and shapes which have been warped by the galvanizing process shall be straightened by being re-rolled or pressed.  The material shall not be hammered or otherwise straightened in a manner that will injure the protective coating.
 
Approval shall be secured from the Engineer if galvanizing is done outside of the Contractor's plant.
 
All galvanized steelwork shall be protected against white storage stain by using an approved dichromate solution treatment immediately following galvanizing.
 
 
APPLICABLE STANDARD AND CODES
All towers manufactured and design shall be generally in accordance with latest revision of the following standards except where specifically directed otherwise.
General
IEC 60826    -  Design criteria of overhead lines
IEC 60652    -  Loading tests on overhead line structures
ISO 1459    -  Metallic coatings - Protection against corrosion by Hot Dip Galvanizing
ISO 1461    -  Hot dip galvanized coatings on fabricated iron and steel articles
ISO 12944    -  Paint coatings, corrosion protection, and structural steelwork
ISO 898-1    -  Mechanical properties of fasteners. Part 1-Bolts, Screws and studs
ISO 630    -  Structural Steels - plates, wide flats, bars, sections and profiles
ISO 657    -  Hot rolled structural steel plates tolerances on dimensions and shape
ISO 7411    -  Hexagon Bolts for high strength structural bolting with large width across flats
ISO 657-5    -  Hot rolled Structural Steel Sections equal and unequal leg angles
ISO 7452    -  Hot rolled structural steel plates tolerances on dimensions and shape
BS EN 50341-1  - Overhead electrical lines exceeding AC 45kV -General Requirements
BS 8004    -  Code of Practice for Foundations
BS 8110    -  Structural use of concrete
ANSI10-97    - Design of latticed steel transmission structures
IEC 60050 (151)                         International Electro-technical Vocabulary
                                       Part 51 Electrical and Magnetic Devices
IEC 60050 (601)                      Chapter 601: Generation, transmission and distribution of electricity-General
IEC 60050 (601)                    Chapter 601: Generation, transmission and distribution of electricity-Operation
IEC 60059                              IEC standard current ratings
Chinese Standard
NoCodeDESCRIPTION
1GB/T2694-2003Power Transmission line Steel tower - Technical requirements for manufacturing
2JGJ81-2002Technical specification for welding for steel structure of building
3GB9787-88Measuring and allowable tolerance for hot-rolled equal angle
4GB709-88Measuring and allowable tolerance for hot-rolled plate and strip
5GB/T699-1999Quality Carbon Structural Steel
6GB/T1591-1994Low alloy high strength structural Steel
7GB700-88Carbon Structural Steel
8GB222-84Method of sampling steel for determination of chemical composition and permissible variations
9GB/T228-2002Method for Tensile testing of metals
10GB/T232-1999Method for Bending test of metals
11GB/T5117-1995Carbon Welding Rod
12GB/T5118-1995Low Alloy Welding Rod
13GB/T8110-1995Welding wires for gas shielding arc welding of carbon and low alloy steels
14GB/T10045-2001Carbon steel flux cored electrodes for arc welding
15JB/T7949-1999Weld outer dimensions for steel construction
16GB50205-2001Test Standard for Acceptance of Steel Structure
17GB/T470-1997Zinc Ingot
18GB3098.1-2000Mechanical properties of fasteners-Part 1:Bolts, screws and studs
19GB3098.2-2000Mechanical properties of fasteners-Part2: Nuts, and thread
20GB3098.3-2000Mechanical properties of fasteners-Part3: Fastening screw
21GB/T5780-2000Helical Bolts Grade C
22GB/T41-2000Helical Nuts Grade C
23GB/T90-2002Flat Washer Grade C
24GB/T13912-2002Metal Coating, Technical Requirement and Test Method for Hot-dip galvanized Metal Parts
 
 
American Standards:
StandardDescription
ASTM A6/A6MStandard specification for general requirements for rolled structural steel bars, plates, and sheet piling.
ASTM - 6    -  General Requirements for delivery of Rolled Steel Plates, Shapes, sheet Piling Bars for  structural used
ASTM A36/A36-M-97aStandard specification for Carbon structural steel
ASTM A123 / A123M-02Standard specification for Zinc (Hot-Dip Galvanized) Coatings on iron and steel products
ASTM A143 / A143M-03Standard Practise for Safeguarding Against Embitterment of Hot-Dip Galvanized Structural Steel Products and Procedure for Detecting Embitterment
ASTM A153/ A153M-05Standard specification for zinc coating (Hot-Dip) on iron and steel hardware
ASTM A - 194  -   Grade for bolt
ASTM A239Standard practice for locating the thinnest spot in a zinc (Galvanized) Coating on Iron or Steel Articles
ASTM A242Standard specification for High-Strength Low-Alloy Structural steel
ASTM A307Standard Specification for Carbon Steel Bolts and Studs, 60000 PSI Tensile strength
ASTM A370-06Standard Test Methods and Definitions for Mechanical Testing of Steel Products
ASTM A325Standard Specification for structural bolts, steel, Heat treated 120/105 ksi minimum tensile strength
ASTM A-325 or A-354  -  Galvanized hexagonal head of  connection bolt
ASTM A325-97Standard Specification for High-strength Bolts for structural steel Joints
ASTM A384 / A384M-02Standard Practise for Safeguarding Against Warpage and Distortion During Hot-Dip Galvanizing of Steel Assemblies.
ASTM A394-93Standard Specification for steel Transmission Tower, Bolts, Zinc Coated and Bare
ASTMA - 563-    Class and size of nuts
ASTMA - 572   - Chemical composition of steel
ASTM A572/A572-97cStandard specification for High-Strength Low-Alloy Columbium-Vanadium Structural steel
 ASTMA - 615  -   The anchor bolt material
ASTM A673 / A673M-07Standard Specification for Sampling Procedure for Impact  Testing of Structural Steel
ASTM B201Standard practice for testing Chromatic coating on Zinc and Cadmium surfaces
ASTM  E94-93Standard Guide for Radiographic Testing
ASTM E 709-95Standard Guide for Magnetic Particle Examination
ASCE Manual 72    -  Load testing a simple structure
ASCE 10-97Standard Design of latticed steel transmission structures
AWS D1.1American Welding Society D1,1/D1,1M structural Welding code- Steel
ANSI B-182-2Bolts, nuts and washers dimensions
 
DIN VDE 0101                       -  Isokeraunic Level
VDE 0201                              - Climatic and environmental   conditions
CVDE 0210                           -  Minimum safety factors under    simultaneous working loads
ISO R898 Mechanical Properties of Fasteners
BS EN ISO 1461:1991 - High dip galvanized coatings on fabricated iron and steel articles. Specifications and standards
A) BS 5950: Welding Terms And Symbols
B) BS 729: Hot - Dip Galvanised Coating On Iron And Steel Articles
C) BS 2901: Filler Rods And Wires For Gas Shielded Arc Welding: Part 1 Ferritic Steels
D) BS 3692: ISO Metric Precision Hexagon Bolts, Screws And Nuts
E) BS 4360: Weldable Structural Steel
F ) BS 5135: Metal - Arc Welding Of Carbon And Carbon Manganese Steel
G) BS 5950: Part 1: Code Of Practice For Loading Latticed Tower & Masts
Part 2: Guide To The Background And Use Of Part 1"Code OF Practice For Loading"
Part 3: Strength Assessment of Members
H) DD 133 (1986): Code Of Practice For Loading Latticed Tower & Masts
I) BS 4592 (1987): Part 2: Specification For Expanded Metal Grating Panels
J) BS 4592 (1977): Code Of Practice For Protective Coating Of Iron And Steel Structure Against Corrosion
K) BS 4190: Bracing & Flanged Bolts
L) BS 4190: Rolled Steel sections, Flats & Plates
 
If any special requirement, we can design and discuss with client.

 

You Might Also Like