Dental Lab Alloy Zaire Chrome-Cobalt Base Partial Denture Alloy

China Dental Lab Alloy Zaire Chrome-Cobalt Base Partial Denture Alloy, Find details about China Dental Lab Alloy, Dental Ceramic Alloy from Dental Lab Alloy Zaire Chrome-Cobalt Base Partial Denture Alloy

Model NO.
ZAIRE
Yield Strength
96, 000 Psi
Elongation
6%
Hardness
330 Hv
Tensile Strengthn
108, 000 Psi
Trademark
Stardent
Transport Package
Export Standard Packing
Specification
1000g/box
Origin
China
HS Code
90184990
Model NO.
ZAIRE
Yield Strength
96, 000 Psi
Elongation
6%
Hardness
330 Hv
Tensile Strengthn
108, 000 Psi
Trademark
Stardent
Transport Package
Export Standard Packing
Specification
1000g/box
Origin
China
HS Code
90184990
Dental Lab Alloy Zaire  Chrome-Cobalt Base Partial Denture Alloy
 

Physical Data

Melting Range

1320°c-1380°C (2408°F-2516°F)

Casting Temp

1454°C (2650°F)

Hardness

330 HV

CTE

-

Yield Strength

96,000 PSI

Tensile Strength

108,000 PSI

Elongation

6%

Density

8,70 g/cm3

Specific Gravity

8,40 g/cm3

 

 

Material Identification

Chrome-Cobalt Base Partial Denture Alloy

Trade Name

None-Precious Alloy

Commercial Name

Zaire

ngredients & Hazards

IngredientsCas #% Composition by weight
Cobalt (Co)(7440-48-4)60-62%
Chromium (Cr)(7440-47-3)28-30%
Molybdenum (Mo)(7439-98-7)5-6%
Silicon (Si)(7440-21-3)<1%
Manganese (Mn)(7439-96-5)1%
Iron (Fe)(7439-89-6)<1%
Carbon (C)(7440-44-0)0.30-0.40%*

(*) 0.30% Carbon 330HV. ("Zaire" w/ regular hardness) (*) 0.40% Carbon 360HV ("Zaire" hard)

Solid Form

  • Fire and explosion resistant
  • Insoluble in water
  • No odor
  • Non-toxic
  • In solid form no special precautions are required

Hazard Data

  • Chromium
  • Eight (8) hr. Tlv - 5 mg/m3
  •  
  • Molybdenum
  • Eight (8) hr. Tlv - 1 mg/m3
  •  
  • Silicon
  • Twa - 10 mg/m3



 

PROCESSING TECHNIQUE

Use investments for high-heat Chromium-Cobalt partial denture alloys only. Burnout at the temperatures and time recommended by the investment manufacturer or at a minimum of 1,850°F (1,010°C) for 1.5 hrs.

TORCH CASTING

  1. Use a single-orfice tip or a multi-orfice tip.
  2. Set gauge at 20 psi oxygen and 8 psi acetylene.
  3. Give the spring-type casting arm three turns on an average casting.
  4. Place a sufficient amount of alloy in the preheated crucible.
  5. Heat the alloy evenly until the alloy begins to melt. At this point, drop a small amount of flux onto the heated metal to make the piece flow together. When the metal melts into a single mass, release the casting machine arm.
  6. Allow the casting arm to rotate for a minimum of twenty seconds. Then remove the mold and set it aside to bench cool.

INDUCTION CASTING

It is crucial to follow the manufacturer's instructions in the operation of your specific equipment, due to the various types of induction machines available on the market (such as Manual, Semi-Automatic, and Fully Automatic, etc.). Exercise care in placing virgin metals or buttons in the crucible. Do not drop in ingots. Instead, use large tweezers to load the crucible, which will help prevent cracking of the crucible. For manual operators, when all the metal has melted together as one joined mass, release machine immediately to prevent overheating of the metal.

FINISHING STEPS

*Cut the sprues
*Trim remaining metal from sprues
*Clean up the inside of clasps and uprights with Taper Stone
*Grind or trim tight areas with an Inverted Cone
*Go over the entire case with a Small Barrel for polishing
*Sandblast and prepare for polishing

CONVENTIONAL ELECTROPOLISHING

Use conventional electropolishing systems accepted and recommended for high-heat Chromium-Cobalt partial denture alloy only. Consult manufacturer's instructions and specifications for proper operating procedures. Rubber point all clasps and go over all surfaces that have been rubber wheeled.

PRECAUTIONS

When melting, grinding, or polishing alloy, use adequate ventilation, vacuum systems, protective eyewear, and protective masks and clothing.

 


Dental Lab Alloy Zaire Chrome-Cobalt Base Partial Denture Alloy
Dental Lab Alloy Zaire Chrome-Cobalt Base Partial Denture Alloy
Dental Lab Alloy Zaire Chrome-Cobalt Base Partial Denture Alloy
Dental Lab Alloy Zaire Chrome-Cobalt Base Partial Denture Alloy
Dental Lab Alloy Zaire Chrome-Cobalt Base Partial Denture Alloy
Dental Lab Alloy Zaire Chrome-Cobalt Base Partial Denture Alloy
Dental Lab Alloy Zaire Chrome-Cobalt Base Partial Denture Alloy








Payment:
1. Full payment should be made within 5 working days of placing your order.
2. After deliver goods, we will send the tracking number to you.
3. We accept Paypal, Western union and bank transfer.
4. Please make sure your payment address is correct.
5. All prices are EXW.

Our main products are dental unit,dental files,dental burs,dental handpiece,dental material,air compressor,autoclave,X ray unit,ultrasonic scaler,light cure,air turbine handpiece,intra-oral camera and apex locator.Meanwhile we can supply branded products from Dentsply,Saeshin,Saeyang,NSK,Woodpecker,Vita,Meta,Coxo,Greatstar,BEING,SINOL,RUNYES,GAPADENT, SUPLINE,SMIC and so on.
Stardent Equipment Co.,Limited is located in Foshan,Famous Town of Chinese Gongfu,central area of China, a traditional commerce city with rich history and culture. 
"For your better clinic,for all better teeth,for most beautiful smile" is our goal of developing.Welcome to visit website or company to know more.Thanks very much.

Any questions, please contact us.


Dental Lab Alloy Zaire Chrome-Cobalt Base Partial Denture Alloy
Dental Lab Alloy Zaire Chrome-Cobalt Base Partial Denture Alloy


Dental Lab Alloy Zaire Chrome-Cobalt Base Partial Denture Alloy
Dental Lab Alloy Zaire Chrome-Cobalt Base Partial Denture Alloy