Products

250- 17D Intermediate Copper Wire Drawing Machine

China 250-17D Intermediate Copper Wire Drawing Machine, Find details about China Wire Drawing Machine, Copper Wire Drawing Machine from 250-17D Intermediate Copper Wire Drawing Machine

Max. Number of Block
18
Certification
ISO
Condition
New
Trademark
SUNTECHMACH
Transport Package
Seaworthy Packing
Specification
5200*200*1700mm
Origin
China
HS Code
8463300000
Max. Number of Block
18
Certification
ISO
Condition
New
Trademark
SUNTECHMACH
Transport Package
Seaworthy Packing
Specification
5200*200*1700mm
Origin
China
HS Code
8463300000
250-17D Intermediate Copper Wire Drawing Machine
1. General description
This machine is used to draw Φ0.5-φ2.5mm copper wires.

2. Technical parameter
No.ItemSpecification
1Inlet diameterMax Φ3.5mm
2Outlet diameterΦ0.5-Φ2.5mm
3Max speed of drawing25m/s  (Φ 0.5mm)
4Tower capstan diameter Φ250mm
5Capstan diameterΦ250mm
6Number of die18
7Outer Diameter of dieΦ25mm
8Spooling bobbin sizePND500
9Main motor power55kW (AC)              
10Power of motor for double take up11kW (AC )X2
11Machine dimension2400×1250×1400mm
12.Anneal unit power60V,2500A (DC) 
 
3. Machine components
No.ItemQuantity
1Payoff stand1 set
2Main drawing machine with annealing1 set
3Steam generator1 set
4Electric control and operating desk1 set

4. Detailed introduction:
4.1 Payoff stand
1) Dimension of Payoff (mm) : 300 * 300 * 650
2) Type: Over head
4.2 Main drawing machine
1) Type: slip type.17-die copper wire drawing machine
2) Body structure: Body welded from Q235 plate molding, via annealed to remove internal stress, then by precision milling machine.
3) Inlet wire position on the left side of machine body panel, with 6 inlet wire holes. Outside installation sump.
4) Shaft material by 40CrMo steel, quenched HRC25-27, to ensure removal of internal stress, and improve the rigidity of the workpiece, with the Department by grinding to ensure concentricity and roundness balance.
5) The machine drives transmission by flat belts.
6) Using spray ceramic Capstan, double slot 4 layers 4 units and final Capstan single layer one unit.
7) First eye mold as an independent mold,the 2nd to the 17st eyes mode are pig iron casting, the body is small, increasing the lead to take working space.
8) Capstan and lubrication of wire drawing dies, at the top install movable pipe joints, does not affect the threading operation.
9) The drawing emulsion trough is provided with doors made of stainless steel, which prevent lubricant from overflowing.
10) Lubricant equipment:
Working pressure: 0.2 ~ 0.4 Mpa
Temperature: ≤30ºC
Rate of flow: 25 ~ 30(m3/h)
4.3 Annealing device
1) Type: vertical DC annealing, speed tracking automatically
2) Diameter of annealing inlet wire :Φ0.5mm-Φ2.5mm
3) Max linear speed of annealing: 25m/s
4) 3pieces-Diameter of annealing nickel-conducting ring: 300mm.
5) The stretching force of softening conductor is even and stable and reaches the international requirement of the stretching rate.
6) Annealing is a two-period process: preheating period and annealing period
7) Softening room is protected by steam with hand-operated pressure regulating valve.
The pressure of steam: 0.2Mpa
The dosage of steam: 15kg/h
8) Equipped with air-drying device which is hand-operated.
Working pressure: 0.6~0.7 Mpa
Flow quantity: 300 L/min
9) Annealing cooling adopts water circulatory cooling. Heat exchanger is cooled by the wire. 
Flow: 25 m³/H
Working pressure of water: 0.2-0.4 Mpa
4.4   Φ50Double take-up
1) Spooling bobbin size: PND500
2) Max. take-up speed: 25m/s
3) Take-up motor: 11KW (AC)X2
4) 90W Belt-type synchronous motor cable, stability and fast response.
5) Traverse pitch is fixed. 
6) Arm cushion detection, automatic correction coiling, tension can be adjusted according to wire diameter.
7) Uniaxial Quill nut is fixed spool.
8) Brake is pneumatic butterfly type.
 
5. Electrical control system
NoItemBrand
1PLCSIEMENS
2Frequency converterINOVANCE
3Low-voltage apparatusSCHNEIDER
4Touch screenSIEMENS
5BEARINGNSK, JAPAN
6MotorSIEMENS

5. Reference photos:
250-17D Intermediate Copper Wire Drawing Machine
250-17D Intermediate Copper Wire Drawing Machine
250-17D Intermediate Copper Wire Drawing Machine
250-17D Intermediate Copper Wire Drawing Machine
250-17D Intermediate Copper Wire Drawing Machine
250-17D Intermediate Copper Wire Drawing Machine
250-17D Intermediate Copper Wire Drawing Machine
250-17D Intermediate Copper Wire Drawing Machine
250-17D Intermediate Copper Wire Drawing Machine
250-17D Intermediate Copper Wire Drawing Machine

6. Packaging & Shipping
We can pack it by pallet, or according to the customers' specific requirements.

7. Our Services
In order to guarantee the customers are able fully to operate the machine, if the customer need, we can help customer training, includes:
1. Correct operating mode
2. Correct maintenance way
3. Remove simple problem

8. RFQ:
Dear customer, 
Thanks for your viewing.
For better recommendation, pls tell us the follow information when sending us inquiry.
1. Wire material
2. Inlet and outlet wire diameter
3. Spool size for take up

Thanks and best regards

250-17D Intermediate Copper Wire Drawing Machine

You Might Also Like