Laser Welding and Cutting Machine Fume & Dust Purifier

China Laser Welding and Cutting Machine Fume & Dust Purifier, Find details about China Intelligent Dust Collector, Laser Cutting Fume Extractor from Laser Welding and Cutting Machine Fume & Dust Purifier

Model NO.
KSJ-3.0G
Air Volume
3600±100m³/H
Motor Power
3kw
Filter Area
40m²
Trademark
Kaisen
Transport Package
Wooden Case
Specification
900*850*1745mm
Origin
Shanghai, China
HS Code
8421399090
Model NO.
KSJ-3.0G
Air Volume
3600±100m³/H
Motor Power
3kw
Filter Area
40m²
Trademark
Kaisen
Transport Package
Wooden Case
Specification
900*850*1745mm
Origin
Shanghai, China
HS Code
8421399090

KSJ-3.0G Laser Welding Machine Smoke Fume Extractor

Laser Welding and Cutting Machine Fume & Dust Purifier


 
Working Principle

The fume comes from the processing will be sucked into the extractor through the hood, first the fume passes the 1st layer preventer plate which will ramify the fume to avoid residual sparks enter into filter layer directly. Finally, the fume enters the second layer of HEPA filter cartridge for ultimate purification, and HEPA' s filtration efficiency can reach 99.9%. As the filtering precision of the main filter cartridge reaches the indoor emission standard, the filtered clean air can be directly discharged indoor via the vent in the bottom of the extractor.
 

Product introduction

Incorporated world leading environmental technology, economical mobile fume extractor is a technically advanced industrial dust & fume extractor, it's developed with full consideration of the forming, characteristics and harm of fumes and based on actual conditions of cutting and welding workshop.

Technical parameters

Laser cutting fume extractor KSJ-3.0G

Features

1. The air purifier applies to all kinds of soot purifications caused by welding,  grinding, as well as recycling of rare metals, precious materials, etc  

2.  For the potential of fire and molten slag particles, three protective measures are used inside purifier, to make it a longer life, more secure and reliable.

3.  Intelligent model using PLC automatic control makes operation easy, filter rotates with the use of full-automatic cleaning in all directions, so that there is a more thorough cleaning filter surface, always to guarantee a constant air volume absorption. Filter is made of  imported microporous PTFE film ,and can filter out welding fume of 0.1μm filtering with high precision can meet GB indoor emission standards. And can filter out welding fume of 0.1μm

4. Power phase sequence instructions,  short-circuit protection for lack of phase, with shutdown protection measures when too high temperature.

5. With large air volume, low noise and better capture effect. Suction hose uses the real anti-temperature, wear-resistant compounded materials, without crack and damage for  sparks but  longer life.

6. Photoelectric switch, efficient and energy-saving, with lighting fixtures cantilever cover (optional).

7. The plasma and laser cutting fume extractor averagely divides the cutting platform into partitions of equal width a dust collector for both fume absorption and dust holding is configured in each partition. The valve is set at the end of each partition, and is in linkage with the pneumatic tappet. When the cutting gun arrives any position, the corresponding valve automatically opens, and always ensures that ventilation is just implemented only in the cutting areas that generate fume. This system greatly reduces the amount of wind needed, thus saves the consumption of electric energy.

Parameters 

 

Model

KSJ-1.5G

KSJ-3.0G

Treatment of air flow

2400 m3/h

4000 m3/h

Motor Power

1.5 Kw

2x1.5Kw

Voltage

380 V/50 Hz

380 V/50 Hz

Filtering area

20 m2

40m2

               Cleaning Methods

Automatic Cleaning

Automatic Cleaning

Compressed Air

0.5~0.6 MPa

0.5-0.6 Mpa 

Filtration efficiency

>99.9%

>99.9%

Noise

≤75±5dB(A)

≤75±5dB(A)

Weight

275±5Kg

435±10Kg

 

 

 


Company profile

Shanghai Kaisen Environmental Technology Co.,Ltd has beenalways committed to designing, R&D and manufacturing of industrial dust collectors.Since 2007 we had been engaged in dust collectors for ten years.Our products are extensively applied to the processing of welding, cutting, grinding, painting, casting, chemical, wood processing, paper and other industries.

The products of Kaisen include mobile welding dust collectorwall mounted dust collectorhigh vacuum dust collector, laser & plasma cutting dust collector, grinding fume collector, 3D printer dust collector and system solution of fume disposal. Also,Kaisen had passed ISO9001, ISO14001 and OHSAS18001 approvals, most of products are CE certification.


Laser Welding and Cutting Machine Fume & Dust Purifier
Laser Welding and Cutting Machine Fume & Dust Purifier
Laser Welding and Cutting Machine Fume & Dust Purifier
Laser Welding and Cutting Machine Fume & Dust PurifierLaser Welding and Cutting Machine Fume & Dust PurifierLaser Welding and Cutting Machine Fume & Dust PurifierLaser Welding and Cutting Machine Fume & Dust Purifier