Outdoor Waterproof IP65 cell phone signal booster 900 1800 GSM frequency shifting repeater
Description
The Frequency Shifting Repeater (FSR) consists of two parts: Donor Unit and Remote Unit. The Donor Unit receives the downlink signal from base station and shifts it to relevant channel, then transmits to the Remote Unit via relay antenna. The Remote Unit reconverts the received signal to the primary channel and covers the whole coverage areas. The Remote Unit receives the mobile signal from coverage areas and also shifts it to relevant channel, then transmits to the Donor Unit via relay antenna. The Donor Unit will reconvert the signal to uplink signal of the primary channel then send to the base station. Thereby available expand and fill signal area where mobile communication coverage is blind, enhance communication quality. Applicable to cover in the area where lack for fiber optic connection and uneasy to lay cables or use to district network optimization, along with occasion that installation is limited and the transceiver antenna isolation is unsure. Such as: the telegraph pole nearby the road, iron tower and the roof of the country etc.
Frequency Shifting Repeater Series:
According to relay frequency range the FSR can be sorted into In-band FSR and Out-of-Band FSR.
In-band FSR:the link frequency is within the working band of BTS;
Out-of-Band FSR:the link frequency is out of the working band of BTS.
As per the method of frequency shifting the FSR can be sorted into Band-selective FSR and channel selective FSR.
Band-selective FSR:shift and amplify the signal frequency in given band.
Channel selective FSR: shift and amplify the signal frequency in given channel (Single Channelized, Dual Channelized, Four-channel Channelized, Six-channel Channelized, and Eight-channel Channelized FSR).
As per the method of source picking up by the Donor Unit, the FSR can be sorted into Cable-Access FSR and Wireless-Access FSR.
Cable-Access FSR: receive base station signal via a coupler link to the base station;
Wireless-Access FSR: pick up base station signal in air via Donor Antenna (applicable when the coverage areas under outspread are far away from base station).
RF SpecificationsItem | Specification For Cable-Access Band-selective FSR(CB-FSR) | Remark |
Up-Link | Down-Link |
Work Frequency range | 885-915 MHz | 930-960 MHz | For GSM Device |
1710-1785 MHz | 1805-1880 MHz | For DCS Device |
Transmitting frequency | 1710-1785mhz Or Customized | 1805-1880mhz Or Customized | For GSM Device |
885-915mhz Or Customized | 930-960mhz Or Customized | For DCS Device |
Pass band BW | 0.2-30Mhz(Customized) | For GSM Device |
0.2-75Mhz(Customized) | For DCS Device |
Output Power | Donor Unit | -10-0 dBm | 30-40 dBm | (Customized) |
Remote Unit | 30-40 dBm | 30-43 dBm |
Nominal Gain | Donor Unit | 45-55dB | 45-55dB | (Customized) |
Remote Unit | 75-105dB | 75-108dB |
Pass Band Ripple | ≤3dB | For GSM Device |
≤6dB | For DCS Device |
Gain Adjust Rang | 0-30dB in 1 dB steps | |
AGC Rang | 0-30dB | |
Max. ALC level | ≥25dB | |
Intermodulation attenuation | ≤-45dBc | |
Spurious emission | 9kHz-1GHz | ≤-36dBm | |
1GHz-12.75GHz | ≤-30dBm | |
Noise Figure. | ≤5dB(at maximum output power) | |
Group delay | ≤6us | |
VSWR | ≤1.5 | |
RF Connectors | N - female | |
Impedance | 50 Ohms | |
| | | | | |
Item | Specification For Wireless-Access Channel-selective FSR(WC-FSR) | Remark |
Up-Link | Down-Link |
Work Frequency range | 885-915mhz | 930-960mhz | For GSM Device |
1710-1785mhz | 1805-1880mhz | For DCS Device |
Transmitting frequency | 1710-1785mhz Or Customized | 1805-1880mhz Or Customized | For GSM Device |
885-915mhz Or Customized | 930-960mhz Or Customized | For DCS Device |
Pass-band BW | 0.2-30Mhz(Customized) | For GSM Device |
0.2-75Mhz(Customized) | For DCS Device |
Number of channels | 1-8 | |
Channel programming | In 200KHz Channel spacing | |
Output Power | Donor Unit | 27-37 dBm | 30-40 dBm | (Customized) |
Remote Unit | 30-40 dBm | 30-43 dBm |
Nominal Gain | Donor Unit | 60-85dB | 60-85dB | (Customized) |
Remote Unit | 75-105dB | 75-108dB |
Pass Band Ripple | ≤3dB | For GSM Device |
≤6dB | For DCS Device |
Gain Adjust Rang | 0-30dB in 1 dB steps | |
AGC Rang | 0-30dB | |
Max. ALC level | ≥25dB | |
Intermodulation attenuation | ≤-45dBc | |
Spurious emission | 9kHz-1GHz | ≤-36dBm | |
1GHz-12.75GHz | ≤-30dBm | |
Noise Figure. | ≤5dB(at maximum output power) | |
Group delay | ≤16us | |
VSWR | ≤1.5 | |
RF Connectors | N - female | |
Impedance | 50 Ohms | |
| | | | | |
Supervising SpecificationsSelf diagnostic platform | Microprocessor based |
Alarms | Yes, amplifiers status, power amplifiers status, power supply failure, battery backup failure, temperature, AGC, RF overload, poor antenna isolation. |
Local management and supervising | Built-in gain adjustment interface and alarms/status LEDs, PC access via RS-232 (OMS) |
Remote management and supervising | Remote access via wireless GSM SMS modem OR GPRS Modem OR Ethernet, option RC (OMS) |
Application: Outdoor: Airports, Golf Courses, Tourism Regions, Villages, Highway, Tunnels, Mining Districts etc.
Indoor: Hotels, Exhibition Centers, Shopping Malls, Gymnasium, Basements, Offices, Factory, Hospital,Entertainment, Packing Lots etc.Shipping
1. We will send the goods within 10-15 days after full payment has been confirmed, detail shipping time depend on order quantity.
2. Multiple delivery method for selection, by air, by land, by sea or by expression courier.Our present manufacturing service:1) GSM/CDMA/WCDMA/IDEN/DCS/PCS/LTE/TETRA/DMR/VHF/UHF and other Repeaters (PICO Repeater/ Dual band Repeater/ Fiber Optical repeater/ Band or frequency selective repeater/ Frequency Shifting repeater) and series Trunk Amplifiers.
2) Functional Units: Low-noise Power Amplifier Integrative Module, Low-noise Band Selective Power Amplifier Integrative Module, Power Amplifier, Low-noise Amplifier, Channelized Device, Band Selective Device, Band Selective Frequency Shifting Device.
3) All kinds of accessories: Antenna/ Filter/Power divider/Connector/ Cable/Coupler/Combiner/Duplexer.
4) OEM/ ODM is available.
Company information:Our company, Quanzhou L-TEL Communication Equipment Co.,Ltd. was founded in 2007, located in the technology economically developed city of Quanzhou, Fujian,China. We are focusing on the development, production and sales of a variety of mobile communication repeaters, signal amplifiers and function modules. We are a professional manufacturer specializing in perfect solutions for wireless signal coverage for a variety of occasions. With years of experience in product and market, we have complete series of product variety. Our products are widely used in China Mobile, China Unicom, China Telecom, China Police-Fire cluster communications, military communications, and other communication systems, and also exported to Southeast Asia, the Middle East, North America, South America, Europe and other countries and areas around the world. For more informations,please feel free to contact with us!!!