Instructions:

Launch X431 V is a high cost-effective automotive diagnostic device developed based on Android 9.0 System. It adopts 2.0GHz Quad-core processor, which runs faster and more stable. It is equipped with DBSCar IV connector as standard, which can be directly inserted into the slot of the host connector, easy to use and not easy to be lost. X431 V can cover more than 98% of the car models in the market, realize the fault diagnosis of the whole system, and has many advantages such as strong diagnosis function and accurate test data.

Top 8 Reasons to Get Launch X431 V V5.0 8inch:

Launch X431 V V5.0 8inch Functions:
1. All System Diagnostic Tool

1. Full Diagnose Function: X431 V can diagnose the electronic control system of prevailing vehicle models covering Asian, European, American and China. Full range car models and Full car systems diagnose make it a professional automotive diagnostic tool
2. Diagnosis functions include: Read DTCs, Clear DTCs, Read datastream. Special Funtion etc.
3. Bidirectional control: Bi-Directional Control which is used to request information or command a module to perform specific tests and functions
4. Actuation Test: it can send information to and receive information from a vehicles control module.
5. Key Programming: if you know you the PIN# of your car, x431 v can match a new key for you .
6. ECU Coding: after replace a new ecu for car, x431 v can help you code it. It is very useful for mechanic.
7. Remote Assistance: launch x431 v support remote diagnosis, you need help from other mechanic, open the remote control function.

1. . If the service lamp is on, you must provide service for the car. After service, you need to reset the driving mileage or driving time so that the service lamp turns off and the system enables the new service cycle.
2. . After changing engine oil or electric appliances that monitor oil life, you need to reset the service lamp.'

1. . To reset the steering angle, first find the relative zero point position for the car to drive in straight line. Taking this position as reference, the ECU can calculate the accurate angle for left and right steering.
2. . After replacing the steering angle position sensor, replacing steering mechanical parts (such as steering gearbox, steering column, end tie rod, steering knuckle), performing

1. . If the brake pad wears the brake pad sense line, the brake pad sense linesends a signal sense line to the on-board computer to replace the brake pad.After replacing the brake pad, you must reset the brake pad. Otherwise, the car alarms.
2. . Reset must be performed in the following cases:

1. . When the ABS contains air, the ABS bleeding function must be performed to bleed the brake system to restore ABS brake sensitivity.
2. . If the ABS computer, ABS pump, brake master cylinder, brake cylinder, brake line, or brake fluid is replaced, the ABS bleeding function must be performed to bleed the ABS.

1. The ECU is replaced and the ECU does not yet store throttle working features.
2. The ECU is disconnected from power and the ECU memory is lost.
3. The throttle assembly is replaced.
4. The intake pipe is replaced or removed, which affects idle speed control by ECU and throttle body.
5. The throttle is cleaned. Although the idle throttle potentiometer features remain unchanged, with the same throttle opening, the air inflow has changed and idle speed control features have changed.

1. Main battery is replaced. Battery matching must be performed to clear original low battery information and prevent the related control module from detecting false information.

1. Battery monitoring sensor. Battery matching is performed to re-match the control module and motoring sensor to detect battery power usage more accurately, which can avoid an

error message displaying on the instrument panel.
7) Diesel Particulate Filter (DPF) Regeneration
DPF regeneration is used to clear PM (Particulate Matter) from the DPF filter through continuous combustion oxidation mode (such as high temperature heating combustion, fuel additive or catalyst reduce PM ignition combustion) to stabilize the filter performance.
DPF regeneration may be performed in the following cases:
The exhaust back pressure sensor is replaced.
The PM trap is removed or replaced.
The fuel additive nozzle is removed or replaced.
The catalytic oxidizer is removed or replaced.
The DPF regeneration MIL is on and maintenanee is performed.
The DPF regeneration control module is rep
Tire Pressure Monitor System Reset
8) Tire Pressure Monitor System Reset:
This function is used to reset the tire pressure sensor. When the car tire air pressure fault indicator is on, after the repair, the tire pressure system needs to be reset by the tire pressure reset function. and the tire pressure fault indicator is extinguished.
9) Gear Learning:
The erankshaft position sensor adaptive learning, the crankshaft position sensor learns the machining error of the erankshaft teeth, and stores it in the computer to more accurately diagnose the engine misfire.
10) Immobilizer Matching:
In order to prevent the car from being used by the illegal key, the car can be opened and used after the anti-theft control system on the car recognizes and authorizes the remote control key through the anti-theft key matchi ng fun ction.
11) Fuel Injector Coding:
This function can write the actual code of the injector or rewrite the code stored in the ECU into the code corresponding to each cylinder nozzle, so as to more accurately control or correct the fuel injection amount of each cylinder.

High quality carton boxes

Delivery within one week after receipt of payment ,By FedEx/DHL/UPS

SALES NETWORK
The company pursues high standard manufacturing and qualified products. All the products had passed the quality system certification of ISO9001:2008 & CE certificate and entered European market. Depending on the stable and lasting capabilities, our products are well known to international market such as Southeast Asia, Eastern Europe, Middle East , Africa, Russia, Mongolia, Bulgaria ,Albania, Argentina, South Africa, Germany, Romania, Ukraine, Haiti, Iraq, Britain, Brazil, Malaysia Indonesia, Australia, and so on etc. and with the reliable and stable quality, our company also has a good reputation at home and abroad.

Now, there are more than 80 countries and regions that use our machine

INSTITUTE OF R&D
We has its own independent research institute. It is now the best comprehensive research institute for the technological development of experimental equipment. And it is one of the first national level corporate centers approved by SETC(State Economic and Trade Commission) and got the grade-A certification for the design of experimental equipment. Ever since a long time ago, the institute is engaged in the general and basic research of heavy equipment, the research of key project and complete plants, and the research for the development of engineering equipments, major national technical equipments and new equipments.

INTERNATIONAL TECHNOLOGY
More than 30 people of our research institute had ever visited more than 10 countries such as the United States, Sweden, India, South Korea, Indonesia, Canada, Russia, Germany and Australia, to study and be trained, introducing international advanced technology. We has continually introduced new products with international standard according to market demand. Our products have also passed CE certification and the EU SGS certification of Sweden.

HONOR
Our company has independently developed a range of products, not only represent the advanced international level in the same industry, and gain praise from customers at home and abroad with the advantages of high-quality and low power consumption. We've gotten four national patent certifications and there are three patents have benign reported to national IPO.

Q: ARE YOU TRADING COMPANY OR MANUFACTURER ?

A: We are test bench assembling factory. We have had test bench for 20 years.

Q: HOW LONG IS YOUR DELIVERY TIME?

A: Generally it is 5-10 days if the goods are in stock. or it is 15-20 days if the goods are not in stock, it is according to quantity.

Q: WHAT IS YOUR TERMS OF PAYMENT ?

A: Payment<=1000USD, 100% in advance. Payment>=1000USD, 40% T/T in advance ,balance before shippment.

Q: How about the use of maintenance technology and equipment ?

A:We have free training about test bench,injector and pump maintenance.

Q: Why should I choose your product?

A: We can provide you the best quality and the most competitive price ,and we have our own engineer, if you have any requirements you can contact us directly.