Kraft Paper Factory Directly Dunnage Air Bag for Container Gap Inflator

China Kraft Paper Factory Directly Dunnage Air Bag for Container Gap Inflator, Find details about China Dunnage Air Bag, PP Woven Inflatable Bag from Kraft Paper Factory Directly Dunnage Air Bag for Container Gap Inflator

Basic Info.

Dunnage Bag Inflation Pressure

2.6kg

Air Dunnage Bag Width Range

40cm-120cm

Container Dunnage Bag Length Range

50-330cm

PP Dunnage Bag Color

White+ Yellow

Trademark

ATXEL

Specification

1000mm*1800mm

Origin

China

HS Code

4819400000

Dunnage Bag Inflation Pressure

2.6kg

Air Dunnage Bag Width Range

40cm-120cm

Container Dunnage Bag Length Range

50-330cm

PP Dunnage Bag Color

White+ Yellow

Trademark

ATXEL

Specification

1000mm*1800mm

Origin

China

HS Code

4819400000

Product Desciption

Product Name	Kraft Paper Laminated Dunnage Bag
Outside Materials	150g Kraft Paper Laminated PP Woven
Inner Materials	PA (Polyamide, Nylon); Enhance high barrier performance;
Work Pressure	0.2-0.8 Bar / 3-10 PSI
Bursting Inspection	According SGS Standard
Dunnage Bag Width	50-120cm
Dunnage Bag Length	50-300cm
Dunnage Bag Valve Choice	Fast Inflate Valve or Traditional Valve
Valve Size	10mm or 30mm two kinds

Loading Tips:
Clean the floor of the trailer and inspect floors, walls and roof for nails or holes before loading. Remove or hammer down nails or other sharps.
Load skids tight from front to back and from side to side. Tight means touching.
Use side shifters on the fork lift to position freight in firm contact with the sidewall or other skid of freight. Also to control void size.
Alternate the void from side to side to balance the load.
Put tallest freight in the nose at the first load position and bag it.
Put the most fragile freight towards the nose for the softest ride.
Use additional bags when necessary to stabilize unsteady skids.
Always bag when dropping from two high to one high loading.
Always bag the final load position.
Techniques for Easy Installation:
Insert inflation tool into valve.
Visually locate the best void to install the bag while walking in.
Give the bag a small puff of air to give it some stiffness and bulk.
Insert bag all the way into the void before inflating. Valve should be at top if possible. One hand should be on the inflation tool and one hand should be positioning the bag.
If bagging a high load position, you may tape the bag to the top of one unit before loading the other side.
When inflating, watch the freight not the bag. 1 - 3 lbs psi recommended. When the freight is tight against the wall, disengage the inflator. Don't worry, the bag will not over-inflate! Installation is complete when the inflator blows back.
After inflation, screw on over-cap.
Deflation (Patented walk-away feature):
Remove over-cap, push valve in and twist one quarter turn clockwise.
You can walk-away while bag deflates!
Remove bag, inspect for damage and set aside for reuse.

OUR PRODUCTION RANGE

SIZE (cm)	MATERIAL	(cm)	(Mpa)
050*100	PE/PP+KRAFT	25	0.06	≤3.5T
050*150	PE/PP+KRAFT	25	0.06	≤3.5T
060*100	PE/PP+KRAFT	28	0.06	≤3.5T
060*120	PE/PP+KRAFT	28	0.06	≤4.5T
060*150	PE/PP+KRAFT	28	0.06	≤4.5T
080*120	PE/PP+KRAFT	38	0.06	≤4.5T
080*160	PE/PP+KRAFT	38	0.06	≤4.5T
080*180	PE/PP+KRAFT	38	0.06	≤4.5T
090*120	PE/PP+KRAFT	45	0.06	≤4.5T
090*180	PE/PP+KRAFT	45	0.06	≤4.5T
100*120	PE/PP+KRAFT	50	0.06	≤4.5T
100*160	PE/PP+KRAFT	50	0.06	≤4.5T
100*180	PE/PP+KRAFT	50	0.06	≤4.8T
100*200	PE/PP+KRAFT	50	0.06	≤4.8T
100*220	PE/PP+KRAFT	50	0.06	≤4.8T
100*240	PE/PP+KRAFT	50	0.06	≤4.8T
120*120	PE/PP+KRAFT	60	0.06	≤4.8T
120*180	PE/PP+KRAFT	60	0.06	≤4.8T
120*200	PE/PP+KRAFT	60	0.06	≤4.8T
120*220	PE/PP+KRAFT	60	0.06	≤4.8T
120*240	PE/PP+KRAFT	60	0.06	≤4.8T