Austenitic Stainless Steel
Austenitic steels are the most popular grades of stainless steels because of their ductility, ease of working and good corrosion resistance and are very commonly used in manufacture of piping components. Austenitic steels are non-magnetic and non-hardenable by heat treatment, however they can be hardened by cold working. The most commonly used stainless steel grades are Type 304, Type 316 and Type 321.
Stainless steel grades with suffix L have low carbon content. The low carbon content provides good weldability and good corrosion resistance after welding, however they have lower strength than the grades with higher carbon content. The dual certified grades of stainless steel are commonly used in the industry such as SS 304/304L or SS 316/316L. For e.g. the SS 304/304L dual certified grade has lower carbon content similar to SS 304L grade but higher mechanical strength of SS 304 grade.
Type 304 grade contains approximately 18% Chromium and 8% Nickel.
Effect of carbon on corrosion resistance
The lower carbon variants (316L) were established as alternatives to the standards (316) carbon range grade to overcome the risk of intercrystalline corrosion (weld decay), which was identified as a problem in the early days of the application of these steels. This can result if the steel is held in a temperature range 450 to 850°C for periods of several minutes, depending on the temperature and subsequently exposed to aggressive corrosive environments. Corrosion then takes place next to grain boundaries.
If the carbon level is below 0.030% then this intercrystalline corrosion does not take place following exposure to these temperatures, especially for the sort of times normally experienced in the heat affected zone of welds in thick sections of steel.
Effect of carbon level on weldability
There is a view that the low carbon types are easier to weld than the standard carbon types.
There does not seem to be a clear reason for this and the differences are probably associated with the lower strength of the low carbon type. The low carbon type may be easier to shape and form, which in turn may also affect the levels of residual stress left the steel after is forming and fitting up for welding. This may result in the standard carbon types needing more force to hold them in position once fitted-up for welding, with more of a tendency to spring-back if not properly held in place.
The welding consumables for both types are based on a low carbon composition, to avoid intercrystalline corrosion risk in the solidified weld nugget or from the diffusion of carbon into the parent (surrounding) metal.
Dual-certification of low carbon composition steels
Commercially produced steels, using current steelmaking methods, are often produced as the low carbon type as a matter of course due to the improved control in modern steelmaking. Consequently finished steel products are often offered to the market dual certified to both grade designations as they can then be used for fabrications specifying either grade, within a particular standard.

Introduction
Stainless steel grade 317L is a low carbon version of grade 317 stainless steel. It has the same high strength and corrosion resistance as 317 steel but can produce stronger welds due to the low carbon content.
Corrosion Resistance
317L has excellent corrosion resistance in a wide range of chemicals, especially in acidic chloride environments such as those encountered in pulp and paper mills. Increased levels of chromium, nickel and molybdenum compared to 316L stainless steel improve resistance to chloride pitting and general corrosion. Resistance increases with molybdenum alloy content. 317L is resistant to sulfuric acid concentrations up to 5 percent at temperatures as high as 120°F (49°C). At temperatures under 100°F (38°C) this alloy has excellent resistance to solutions of higher concentration. However, service tests are recommended to account for the affects of specific operating conditions that may affect corrosion behavior. In processes where condensation of sulfur-bearing gases occurs, 317L is much more resistant to attack at the point of condensation than conventional alloy 316. The acid concentration has a marked influence on the rate of attack in such environments and should be carefully determined by service tests.
Chemical Composition
The chemical composition of grade 317L stainless steel is outlined in the following table.

• Condensers in fossil
• Pulp and paper manufacturing
• Nuclear fueled power generation stations
• Chemical and petrochemical process equipment.

DN15-DN3000
Maximum weight 6tons
25,000tons production annual year

ANSI B16.5,ANSI B16.47 Series A&B,ANSI B16.48,ANSI B16.36
API 605,API 16D,API 17D
BS4504,BS3293
DIN
AS
EN1092-1
GOST
EEMUA145