Exhaled Breath Condensate Collector (EBC) for Virus Microflow Microbiological Air Sampler

China Exhaled Breath Condensate Collector (EBC) for Virus Microflow Microbiological Air Sampler, Find details about Microbial Air Sampler China, Coriolis Microbial Air Sampler from Exhaled Breath Condensate Collector (EBC) for Virus Microflow Microbiological Air Sampler

Basic Info.

Model NO.

BioscreenII

Collection Efficiency

200UL/Min

Collection Temperature

0~4.C

Average Temperature Descending Speed

5.C/Min

Adapter

12V/10A

Power

96W

Centrifuge Tube

Dia29.1*114.4mm

Breath Blow Pipe

Dia6mm

Dimension

250*220*120mm

Weight

2kg

Trademark

Cape-Golden

Transport Package

Portable Case

Specification

250*220*120mm

Origin

China

HS Code

9027100090

Model NO.

BioscreenII

Collection Efficiency

200UL/Min

Collection Temperature

0~4.C

Average Temperature Descending Speed

5.C/Min

Adapter

12V/10A

Power

96W

Centrifuge Tube

Dia29.1*114.4mm

Breath Blow Pipe

Dia6mm

Dimension

250*220*120mm

Weight

2kg

Trademark

Cape-Golden

Transport Package

Portable Case

Specification

250*220*120mm

Origin

China

HS Code

9027100090

Product Desciption

Exhaled Breath Condensate Collector (EBC) for Virus Microflow Microbiological Air Sampler
Model: BioscreenII

1. Operation & Use
1.1 Preparation
1.1.1 Check the Microflow Microbiological Air Sampler host, power adapter, blowing pipe, gas-liquid separation cover and 50mL centrifugal tube are complete.
1.1.2 Confirm the temperature of host has been cooled to below 4°C.

1.2 Personal Protection
1.2.1 Before Microflow Microbiological Air Sampler collection, put on the face mask and gloves, make well personal protection, and get the waste collection bag ready.

1.3 Temperature Setting
1.3.1 Set the lower limit of temperature: press SET key one time, press UP and DOWN key to adjust, press RST key to confirm. When the sampler's display temperature = temperature lower limit, it will stop cooling.
1.3.2 Set the temperature return difference: long press SET key for 5 seconds, press UP and DOWN key to switch P1, press SET key to select, UP and DOWN key to set the return value, press RST to confirm. When the sampler's display temperature ≥ temperature lower limit + return difference value, the sampler will start refrigeration.
1.3.3 Restore factory settings: long press UP and DOWN key to display 888, it means done.

1.4 Assemble
1.4.1 Power on the sampler Microflow Microbiological Air Sampler, lower the temperature to below 4°C. Assemble the blowing pipe, gas-liquid separation cover and centrifugal tube into together, and insert into the condensing tank.

1.5 Condensate Collection
1.5.1 The object rested for 10 minutes and rinsed his mouth with water before collection.
1.5.2 When the temperature drops to 4°C, the object start blowing into the pipe evenly and normally. Start the timer when the object starts to blow, time 3-5 min, collect about 500-1000μl.
1.5.3 During the collection process, the object should inhale hardly, and blow air at an even speed, blow out the remaining air from the lungs as much as possible, which is beneficial to improve the detection rate. Keep inhaling through nose and exhaling through mouth, the staff should observe whether the object is breathing correctly. If the object have obvious fatigue and cough, the staff should stop the collecting and let the object rest, spit, and then continue collecting.

1.6 Condensate Collecting
1.6.1 After blowing finished, take out the centrifugal tube, unplug the blowing pipe and the gas-liquid separation cover, tighten and seal the cover of the centrifugal tube, make mark, and keep it in cold storage.

1.7 Waste Disposal
1.7.1 Put the used blowing pipe and gas-liquid separation cover into in the return bag, for centralized treatment.

1.8 Repeat Collection
1.8.1 Replace the new blowing pipe, gas-liquid separation cover and centrifugal tube, to prevent cross-contamination. Repeat the above steps and collect again.

2. Caution
2.1 Please do not change the accessories casually.
2.2 Please do not disassemble the sampler casually.
2.3 Please stop the sampler when the fault occurs, and restart after troubleshooting.
2.4 The sampler Microflow Microbiological Air Sampler is not waterproof, do not use in rainwater environment;
2.5 Pay attention to biosafety and make good respiratory protection during collection.

3. Maintenance
3.1 After sampling, disinfect and clean the host surface in time.
3.2 Clean the sampler, dry it, and put it in the portable case.

4. Specification

Collection Efficiency	200μl/min
Collection Temperature	0~4°C
Average Temperature Descending Speed	5°C/min
Adapter	12V/10A
Power	96W
Centrifuge Tube	φ29.1*114.4mm
Breath Blow Pipe	φ6mm
Dimension	250220120mm
Weight	2kg