Products

58kHz Ultrasonic Sensor Probe for Parking Sensor or Distance Measuring

China 58kHz Ultrasonic Sensor Probe for Parking Sensor or Distance Measuring, Find details about China Auto Sensor, Radar Sensor from 58kHz Ultrasonic Sensor Probe for Parking Sensor or Distance Measuring

Model NO.
KT58-1432B
Detection mode
Direct Reflection Type
IP Rating
IP67
Certification
RoHS
Customized
Customized
Trademark
customization
Transport Package
Customization
Specification
customization
Origin
China
HS Code
9018129900
Model NO.
KT58-1432B
Detection mode
Direct Reflection Type
IP Rating
IP67
Certification
RoHS
Customized
Customized
Trademark
customization
Transport Package
Customization
Specification
customization
Origin
China
HS Code
9018129900
1, Part Description:
1Water proof
2extension wire harness (Dia 3.0mm x 200mmL) or customization
3Optional frequency
  
       
2, Electronic specification & physical character
Serial numberDescriptionStandard or testing result ItemDescriptionStandard or testing result
1Part NumberKT58-1432B8Sensor materialPA66 1300S / Nylon
2Center frequency(KHz)58±1.5KHz9Sensor colourBlack or white or customization
3Residual oscillation(ms)1.36ms10Connect 2P x 2.54 with water proof or customization
4TX  SPL(dB)≥11011Operation Temperature-40ºC~+85ºC
5Max. Input Voltage(Vp -p)15012Stock temperature-40ºC~+85ºC
6Sensitivity
(distance)		0.25~1m≤(standard testing by Φ75mm PVC pipe)13Beam angle (degree)
(2 options)		1,   'X:70±15 
2, X:70±15 & Y:110±15
7Recycle sensitivity≥-75db   
 
3,Dimension and detective diagram

58kHz Ultrasonic Sensor Probe for Parking Sensor or Distance Measuring
4. Environmental test
No.Test itemsTest conditionStandard
1High temp storage test144 hours at + 85 ºCAfter the test and place in + 25 ºC (room temp) for 24 hours, the sensitivity and residual vibration change shall not exceed 30% compared with the initial value 
2Low temp storage test144 hours at - 40 ºC
3High temp and high humidity storage test144 hours at + 65 ºC and 85 ± 5% RH
4Thermal shock testParallel 3.9k Ω resistor at both ends of the probe, keep the temp at - 40 ± 5 ºC for 0.5h, and increase the temp to 85 ± 5 ºC within 5 minutes and keep for 0.5h.100 cycles.After the test and place in + 25 ºC (room temp) for 24 hours, the sensitivity and residual vibration change shall not exceed 30% compared with the initial value 
5Vibration testProducts bear the vibration with frequency 10-55hz, amplitude 1.5mm,and sweep rate 1oct / min, from X, Y and Z directions for each 2 hours respectivelyAfter the test and place in + 25 ºC (room temp) for 4 hours, the sensitivity and residual vibration change shall not exceed 30% compared with the initial value 
6Monomer drop test15 free fall tests carried out from 100 ± 10cm height to 50mm thick wooden floorAfter the test and place in + 25 ºC (room temp) for 4 hours, the sensitivity and residual vibration change shall not exceed 30% compared with the initial value
7Strength test of outletApply 9.8N pulling force between shell and wire for 30 secondsThe wire is not loose or falling off, the product function is normal, and the wire is not damaged
8Protection levelPlace the probe in 15cm deep water and soak for 24 hoursTake out the capasual from the water and install it on the test board to measure the distance. The probe works normally without long sound.
9High and low temp characteristic testKeep the temp at -40ºC for 2h,increase to 25ºC and keep for 2h,increase to 85ºC and keep for 2h. After the test and place in + 25 ºC (room temp) for 2 hours, the sensitivity and residual vibration change shall not exceed 30% compared with the initial value
10High and low temp working testUnder high temp 85 ºC, low temp - 40 ºC, working voltage 140 Vp-p, pulse number 20, continuous working 48 hoursProbe works normally (sensitivity and residual vibration are within normal range)
       
       
5.Test conditions and instruments
No.Test itemTest instruments/methodTest condition
1resonant frequencyImpedance analyzerambient temperature 25 ± 5 ºC
2static capacitanceLCR bridge measuring instrumentambient temperature 25 ± 5 ºC
3residual oscillationKT test equipmentambient temperature 25 ± 5 ºC
4sensitivityKT test equipment0.8m at room temperature, target Φ 75mm PVC pipe
5Angle (X & Y axis)KT test board, as per Fig.1Under normal room temperature, the probe is 500mm from the ground, 500mm from the object to be detected, and the object to be detected is Φ 75mm PVC pipe, 1000mm high. The test environment: 2 meters in front and 1.5m in the left and right without obstacles
6Maximum allowable input voltageKT test board and Oscilloscope140vp-p, pulse width 0.5ms,
intermittent: 10ms
7Mean time between failuresaging test rackTest temp 25±5ºC
       
6.Precautions
1. Please confirm with us which industry will be used before purchasing for selection.
2. In order to prevent the sensor from failure, working failure or performance degradation, the anti failure
   function shall be added to the product design, and the product shall not be used under the following or
   similar conditions.
   (a) strong shock or vibration
   (b) prolonged exposure to high temperature and humidity;
   (c)In corrosive gas or sea breeze
   (d)Exposure to dissolved organic matter
   (e)Dusty environment;
   (f)Over allowable input voltage
 
7.Quality assurance
The sensor defects due to the manufacturer during the warranty period of the product can be replaced free of charge.      
The following situations are not covered by the warranty.
1, improper use or handling by users. 
2, changed or repaired by the users. 
3,any other situation that does not belong to the responsibility of the manufacturer, such as natural disasters, accidents, etc.
 

You Might Also Like