MR-WL 203 Minrry Fundamentals Of Pressure Measurement
Pipe Surge Fluid Mechanics Lab Equipment Vocational Education Training Equipment
Description
• comparison of different pressure measurement methods
• measuring positive and negative pressure
• calibration device with Bourdon tube pressure gauge for calibrating mechanical manometers
Measuring pressure is important in the engineering industry, e.g. in plant, turbomachine and aircraft construction and in process engineering. Other fundamental factors such as flow rate or flow velocity can also be determined based on a pressure measurement.
The MR-WL 203 experimental unit enables the user to measure the pressure with two different measuring methods: directly by measuring the length of a liquid column (U-tube manometer, inclined tube manometer) and indirectly by measuring the change of shape of a Bourdon tube (Bourdon tube pressure gauge).
In a U-tube manometer, the pressure causes the liquid column to move. The pressure difference is read directly from a scale and is the measure for the applied pressure. In inclined tube manometers, one leg points diagonally up. A small height difference therefore changes the length of the liquid column significantly.
The principle of the Bourdon tube pressure gauge is based on the change in cross-section of the bent Bourdon tube under pressure. This change in crosssection leads to an expansion of the Bourdon tube diameter. A Bourdon tube pressure gauge is therefore an indirectly acting pressure gauge where the pressure differential is indicated via a transmission gearing and a pointer.
In experiments, pressures in the millibar range are generated with a plastic syringe and displayed on the manometers.
The experimental unit is equipped with two Bourdon tube pressure gauges for measuring positive and negative pressure. The U-tube manometer, inclined tube manometer and Bourdon tube
pressure gauges at the experimental unit can be combined using tubes. A calibration device enables calibration of an additional Bourdon tube pressure gauge using a weight-loaded piston manometer.
Learning objectives/experiments
• familiarisation with 2 different measuring methods:
· direct method with U-tube manometer and inclined tube manometer
· indirect method with Bourdon tube pressure gauge
• principle of a Bourdon tube pressure gauge
• calibrating mechanical manometers
Specification
[1] basic experiments for measuring pressure with three different measuring instruments
[2] U-tube and inclined tube manometer
[3] one Bourdon tube pressure gauge each for positive and negative pressure
[4] plastic syringe generates test pressures in the millibar range
[5] calibration device with Bourdon tube pressure gauge for calibrating mechanical manometers
Technical data
Inclined tube manometer
• angle: 30°
Measuring ranges
• pressure:
· 0…±60mbar (Bourdon tube pressure gauge)
· 0…500mmWC (U-tube manometer)
· 0…500mmWC (inclined tube manometer)
LxWxH: 750x610x810mm
LxWxH: 410x410x410mm (calibration device)
Total weight: approx. 40kg
Scope of delivery
1 experimental unit
1 calibration device
1 set of weights
1 oil, 500mL
1 ink, 30mL
1 funnel
1 syringe
1 set of hoses
1 set of instructional material
Isolating valves enable a wide range of different series, parallel and mixed pipe configurations to be created without draining the system. Flow into the network and flow out from the network at each outlet can be individually varied to change the characteristics of the system.
All clear acrylic test pipes are installed using threaded unions with 'O' ring seals that allow the pipes with different diameters to be repositioned without the use of tools.Self-sealing quick release fittings at strategic points in the network allow rapid connection of the digital hand-held pressure meter, allowing appropriate differential pressures to be measured. Flow leaving any of the outlets in the network is measured using the volumetric facility incorporated on the F1-10 Hydraulics Bench.
2.Ordering Specification
Specifically designed to allow the setting up of a wide range of different pipe arrays (networks)
Pipe network mounted on free-standing support frame for use alongside an F1-10 Hydraulics Bench
Clear acrylic test pipes are all 0.70m long with inside diameters of 1x 6mm, 2x 9mm, 1x 10mm, 1x 14mm
Includes hand-held electronic pressure meter with self-sealing quick-release connections to the pipe network
Flows into and out from the appropriate network can be varied individually
Service
We supply supply7*24 hours service, customer design service, OEM service, buyer label service. With professional engineers team and sales team, we assure you good product quality.
Certificate
Our products takes ISO9001 product management system.
| No. | Feature Name | Details |
| 1 | Customer design | Yes |
| 2 | Warranty | 1 year, 2 years, 3 years or 5 years according to client requirements |
| 3 | Package | Plastic film+ carton+ Fine plywood |
| 4 | Products standard | International didactic equipment standard |
| 5 | Application range | Educational equipment for university, college, vocational training centers |
| 6 | Company philosophy | Supply best quality Chinese products to the worldwide schools. |
| 7 | Self owned brand | Shouldshine, SSEDU, JSS. |
| 8 | Production time | From 10 days to 60 days according to different items |
We also have below equipment, please click the link to see it