Products

2.5g DWDM SFP Optical Transceiver Optic SFP Module

China 2.5g DWDM SFP Optical Transceiver Optic SFP Module, Find details about China 2.5g SFP Module, 2.5g SFP Transceiver from 2.5g DWDM SFP Optical Transceiver Optic SFP Module

Model NO.
DF-XX24-3LCD40-001
Name
2.5g SFP Module
Data-Rate
1.25g
Trademark
Takfly
Transport Package
in Plastic Bag Then in Carton
Specification
SFP module
Origin
China
HS Code
854670000
Model NO.
DF-XX24-3LCD40-001
Name
2.5g SFP Module
Data-Rate
1.25g
Trademark
Takfly
Transport Package
in Plastic Bag Then in Carton
Specification
SFP module
Origin
China
HS Code
854670000
2.5Gbps DWDM SFP Optical Transceiver, 40km Reach

TAKFLY 2.5Gbps CWDM SFP Optical transceivers are compatible with the Small Form Factor Pluggable Multi-Sourcing Agreement (MSA). The transceiver consists of five sections: the LD driver, the limiting amplifier, the digital diagnostic monitor, the 1XX0nm DFB laser and the PIN .The module data link up to 40KM in 9/125um single mode fiber.
The optical output can be disabled by a TTL logic high-level input of Tx Disable, and the system also can disable the module via I2C. Tx Fault is provided to indicate that degradation of the laser. Loss of signal (LOS) output is provided to indicate the loss of an input optical 
signal of receiver or the link status with partner. The system can also get the LOS (or Link)/Disable/Fault information via I2C register access.

Features
  • Data-rate of 2.67Gbps operation
  • 18 CWDM DFB wavelengths laser and PIN or PIN photodetector for 40km transmis Compliant with SFP MSA and SFF-8472 with duplex LC receptacle
  • Digital Diagnostic Monitoring:
  • Internal Calibration or External Calibration Compatible with RoHS
  • +3.3V single power supply
  • Operating case temperature: Standard : 0 to +70°

Applications
  • Switch to Switch Interface
  • Gigabit Ethernet
  • Switched Backplane Applications
  • Router/Server Interface
  • Other Optical Links

Recommended Operating Conditions
ParameterSymbolMin.Typ.Max.UnitNote
Case Operating TemperatureTcase0 70ºC 
Power Supply VoltageVCC3.133.33.47V 
Power Supply CurrentICC  300mA 
Power Supply Noise Rejection   100mVp-p100Hz to 1MHz
Data Rate  2670 MbpsTX Rate/RX Rate
Transmission Distance   40KM 
Coupled FiberSingle mode fiber9/125um SMF

Specification of Transmitter
ParameterSymbolMin.Typ.Max.UnitNote
Average Output PowerPOUT-5 2dBmNote (1)
Extinction RatioER9  dB 
Center WavelengthλC(1XX0)-λ1XX0(1XX0)+λnmDFB Laser Note (2)
Side Mode Suppression RatioSMSR30  dB 
Spectrum Bandwidth(-20dB)σ  1nm
Transmitter OFF Output PowerPOff  -45dBm 
Differential Line Input ImpedanceRIN90100110Ohm 
Output Eye MaskCompliant with G.957 (class 1 laser safety) Note (3)

Notes

1) Measure at 2^23-1 NRZ PRBS pattern
2) "XX" is: 27,29,31,33,35,37,39,41,43,45,47,49,51,53,55,57,59 and 61; "λ" is 7.5
3) Transmitter eye mask definition
       
Specification of Receiver
 
ParameterSymbolMin.Typ.Max.UnitNote
Input Optical WavelengthλIN1270 1610nmPIN
Receiver SensitivityPIN  -18dBmNote (1)
Input Saturation Power
(Overload)		PSAT-3  dBm 
Los Of Signal AssertPA-40  dBm 
Los Of Signal De-assertPD  -24dBmNote (2)
LOS HysteresisPA-PD0.526dB 

Notes

  1. The optical power is launched into SMF.
  2. PECL input, internally AC-coupled and terminated.
  3. Measured with a PRBS 223-1 test pattern @2488Mbps, BER ≤1×10-12APD for 1270nm~1450nm
  4. AC-coupled internally.
Electrical Interface Characteristics
 
ParameterSymbolMin.Typ.Max.UnitNote
Transmitter
Total Supply CurrentICC  AmANote (1)
Transmitter Disable Input-HighVDISH2 Vcc+0.3V 
Transmitter Disable Input-LowVDISL0 0.8V 
Transmitter Fault Input-HighVTxFH2 Vcc+0.3V 
Transmitter Fault Input-LowVTxFL0 0.8V 
Receiver
Total Supply CurrentICC  BmANote (1)
LOSS Output Voltage-HighVLOSH2 Vcc+0.3VLVTTL
LOSS Output Voltage-LowVLOSL0 0.8V

Note
1) A (TX) + B (RX) = 300mA (Not include termination circuit)

Pin Definitions
 
PinSymbolName/DescriptionNOTE
1VEETTransmitter Ground   (Common with Receiver Ground)1
2TFAULTTransmitter Fault. 
3TDISTransmitter Disable. Laser output disabled on high or open.2
4MOD_DEF(2)Module Definition 2. Data line for Serial ID.3
5MOD_DEF(1)Module Definition 1. Clock line for Serial ID.3
6MOD_DEF(0)Module Definition 0. Grounded within the module.3
7Rate SelectNo connection required4
8LOSLoss of Signal indication.   Logic 0 indicates normal operation.5
9VEERReceiver Ground   (Common with Transmitter Ground)1
10VEERReceiver Ground   (Common with Transmitter Ground)1
11VEERReceiver Ground   (Common with Transmitter Ground)1
12RD-Receiver Inverted DATA out.   AC Coupled 
13RD+Receiver Non-inverted DATA out.   AC Coupled 
14VEERReceiver Ground   (Common with Transmitter Ground)1
15VCCRReceiver Power Supply 
16VCCTTransmitter Power Supply 
17VEETTransmitter Ground   (Common with Receiver Ground)1
18TD+Transmitter Non-Inverted DATA in. AC Coupled. 
19TD-Transmitter Inverted DATA in.   AC Coupled. 
20VEETTransmitter Ground   (Common with Receiver Ground)1
Notes
  1. Circuit ground is internally isolated from chassis ground.
  2. Laser output disabled on TDIS>2.0V or open, enabled on TDIS<0.8V.
  3. Should be pulled up with 4.7k - 10kohms on host board to a voltage between 2.0V and 3.6V.MOD_DEF (0) pulls line low to indicate module is plugged in.
  4. This is an optional input used to control the receiver bandwidth for compatibility with multiple data rates (most likely Fiber Channel 1x and 2x Rates).If implemented, the input will be internally pulled down with > 30kΩ resistor. The input states are:
    1. Low (0 - 0.8V): Reduced Bandwidth
    2. (>0.8, < 2.0V): Undefined
    3. High (2.0 - 3.465V): Full Bandwidth
    4. Open: Reduced Bandwidth
  5. LOS is open collector output should be pulled up with 4.7k - 10kohms on host board to a voltage between 2.0V and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal.
2.5g DWDM SFP Optical Transceiver Optic SFP Module



International Exhibitions:
2.5g DWDM SFP Optical Transceiver Optic SFP Module

Company:

Takfly Communications Co., Ltd,founded in 2000, which is a Hi-Tech enterprise having its own brand and specializing in R&D, manufacture and sales of fiber optical communications equipment. It controls the quality constantly and strictly in order to give the best products to the users.

  The main products of TAKFLY including MPO/MTP patch cord, CWDM/DWDM, fiber optic cable, patch cord, pigtail, adapter, PLC splitter, fast connector, attenuator, media converter, POE switch, optic splice closure, optic terminal box, ODF etc.

  Based on the conceptes" High Quality, Reasonable Price, Excellect Service and Mutual Benefit", TAKFLY is becoming a famous brand all over the world. Warmly welcome to be our business partner and let us help you to win more markets!

2.5g DWDM SFP Optical Transceiver Optic SFP Module

FQA :

1. Q: Are you a manufacturer?
A: yes, we are a manufacturer , FTTH solution and data center total solution provider in Shenzhen, China, established in 2000.

2. Q: What's your MOQ?
A: MOQ can be 1 pcs, but the price is not competitive.More quantity,the price will be more competitive.

3. Q: Can you quote FOB price?
A: yes. We can delivery by air, DHL, TNT, UPC, FEDEX, etc. For big quantity we will deliver it by sea.

We can quote price with freight and lead time for you, after you let us know detailed requirements with quantity.

We have competitive shipping forwarders. For more solutions, you can feel free to contact us.

4. Q: How is your quality?
A: Our production is according to IEC, Europe standard. CE, ISO, RoHS, CPR, and ANATEL certified.

All the products are 100% test before delivery.

5. Q: What's your lead time?
A: It depends on the quantity and products. For fiber optic patch cord, the lead time can be 2 -3 working days within 5000 pcs. We keep the regular products in stock. Also, we can deal with urgent orders.

6. Q: What's your warranty?
A: Depends one different product, we have1 years warranty for patch cord since delivery, but only responsible for non-artificial damage. For artificial damage, we can repair it for you for free, freight will be paid by your side.

7. Q: What's your packing?
A: International export standard package.If you need to print your logo on the packing, please let us know before we quote.

8. Q: Can you offer OEM/ODM?
A: yes, we can. all products accept OEM /ODM. we can sign the Confidentiality Agreement.

9. Q: Can I have a sample?
A: It depends on which products, Free sample provide under 10 usd. Freight will be paid by buyer before delivery.

10. Q: How can I order?
A:1.send mail or inquiries with product name, specification, and quantity  to us . Provide your receive address if you need FOB,CIF,CFR price.

2.We will offer our quotation with lead time.

3.After the quotation confirmed, we will send a PI with our bank account.

4.Production will be arranged after the payment received.

5.Confirm the consignee with you before we deliver it.

6.The tracking number will be provided after the delivery.

11. Q: What your payment term?
A: T/T, Western Union, Paypal, MoneyGram at once. For big amounts, can be 50% deposit in advance, 50% balance paid before delivery.

You Might Also Like