China Manufacturer Auricularia,Pumpkin,Clipfish Drying Machine Food,Fruit,Vegetable,Herb Heat Pump Dryer 

About SIBIONO company
We are the main professional factory that develops and exports heat pump dryers.

Advantages of SIBIONO's dryer
Traditional drying equipment may have a large energy expenditure. SIBIONO Heat Pump Dryer uses reverse Carnot principle, uses free air to absorb the heat around, and transfers the heat to the material to be dried. The heat pump dryer is controlled by touch screen with adjustable temperature and low power consumption and its heating efficiency is higher than that of similar equipment. This dryer have many advantages such as energy saving, environmental protection, intelligent 24-hour operation, wide drying range and good effect.Drying materials are clean, and their appearance and taste can be improved for several grades.

Application of SIBIONO heat pump dryer
SIBIONO Heat Pump Dryer Suitable for drying various fruits and vegetables and other agricultural products, animal feed,Seafood, fish, meat, tea, coffee beans, incense, wood. , Industrial materials, etc.

Comprehensive analysis of SIBIONO drying system
1.Energy saving:
Adopt heat pump technology, absorb heat from air and recovery waste heat at the same time
Adopt close dehumidify + circulating drying type, saving operating cost;
2.Exact control temperature and humidity:
The drying temperature can be easily controlled by PLC +Touch Screen control system.
3.Uniform drying:
By using the forced ventilation function, there are partition sheet and fan motors inside the drying chamber to make sure hot air cycle, so the raw
materials can be dried evenly
4.The temperature: 10-75°C, Max 75°C, similar nature drying.
5.The baking plate dimensions and materials can customize as customer request.
6.Good drying quality:
During drying, the material does not craze, does not distortions, non-discoloring, never degenerate, non-oxidize, drying completely, with
good rehydration, keep nutrient content;
7.Safe and reliable operation:
Automatic intelligent control, 24-hour continuous drying; Without waste gas and waste heat pollution,low noise

Introduction to Dryer
1.The main components
The heat pump drying unit mainly consists of four parts: finned evaporator (outer machine), compressor, finned condenser (inner machine) and expansion valve.
2.work process
By allowing the refrigerant to continuously complete the thermal cycle of evaporation (absorb heat from the outdoor environment) → compression → condensation (release heat in the indoor drying room) → throttling → reevaporation, Thereby, the heat in the external low temperature environment is transferred to the drying room, and the refrigerant circulates in the system under the action of the compressor.
 

We have rich experience in drying system projects
Heat pump drying system is widely used in all walks of life,
covering food, fruits, vegetables, medicinal materials, meat, seafood, fish, wood and other fields
Sibino heat pump drying system has been successfully used in many countries and regions.
If you need, please provide material name / quantity/ Dehydration time/ water content requirement, we will provide design scheme and quotation for you

Guangzhou SIBIONO Drying Equipment Co., Ltd. is a manufacturer and exporter specializing in heat pump dryers.

1) Shipment list

Q:electronic expansion valve opening too small
A:adjust bigger
Q:exhaust temperature too high protection
A1: leak gas: check leak point, repair
A2: electronic expansion valve does not working: turn valve body
Q:discharge moisture too slow or does not discharge moisture
A: dehumidify fan power /dehumidify fan was damaged / controller go wrong
Q.hot air circulating fans does not working
A1:Fan was damaged: replace new fan or uninstall damaged fans
A2:part of hot air circulating fan not working: check whether the fans have many ON/OFF switch or some fans was burned
A3: AC contactor use for hot air circulating fans overloading protection: please check power source whether lack phase/connecting port or voltage not stable
Q:Too much more products on trays or too much more trays on trolleys lead to block hot air
A:hot air cannot circulating in drying chamber or too slow wind speed, usually two tray's distance at 8-10cm is reasonable
Q:electronic expansion valve throttle opening too small; or jammed.
A1. electronic expansion valve does not working:turn valve body
A2:Controller adjust electronic expansion valve's opening to small automatically: temperature sensor not accurate-change installation place, exchange 1# and 2# sensor's position
Q:chamber's temperature too high
A:set lower temperature
Q: What's the MOQ for each item?
A: Minimum order for 1 set of machines,More than 2 devices, the price is relatively favorable.
Q: Can you test our dry samples?
A: Yes it is. You can send the materials to us for testing and analysis, we can provide You provide a detailed test report.
Q: Do you give any guarantee to your products?
A: Basically, we have 12 months quality guarantee for Sibiono brand dryer.
Q: Does the machine produce pollutants during operation?
A: Sibiono brand drying machine are environmentally friendly and will not pollute the environment, please rest assured to use
Q: What products can the Sibiono dryer dehydrate? Can grapes be dehydrated?
A: Sibiono brand drying machine can dehydrate many categories of products, including most fruits, fish, wood, medicinal materials, seafood, and flowers.If you want to confirm whether your product is supported, please contact us, thank you
Q: I have sludge to be treated here, can I dry the sludge through Sibiono equipment?
A: There are two types of sludge drying machines under the Sibiono brand, one is a cabinet-type sludge dryer, and the other is an assembly line sludge dryer. You can choose according to the weight of the sludge you need to process.
Q: What about the delivery time?
A: 7 to 30 days for the items need to be manufactured based on your order.

A. Technical service
• We calculate the capacity and recommend the best models.
• We supply you the professional refrigeration technical support and electronic technical support for your installation, debugging and operation.
• We supply the spare parts and technical support in & after the warranty time.
• We supply the training course to your workers at our factory if you need.
B. After-sales service
• Technical support for your installation, operation and maintenance.
• One year's warranty, and you can pay for extended warranty.
• Spare parts and technical support at most economic prices after the warranty.