TDS Meters Pen Water Testers Meters

China TDS Meters Pen Water Testers Meters, Find details about China pH Meters, pH Meter from TDS Meters Pen Water Testers Meters

Model NO.
WKT-PM
Chemical Analysis Type
None
Operating Mode
Keyboard
Heating Mode
None
Off Mode
Manual
Trademark
VICOMETER
Transport Package
Carton
Origin
China
HS Code
9027809900
Model NO.
WKT-PM
Chemical Analysis Type
None
Operating Mode
Keyboard
Heating Mode
None
Off Mode
Manual
Trademark
VICOMETER
Transport Package
Carton
Origin
China
HS Code
9027809900

Tds Meter aqua TDS and ph water testers

TDS Meters Pen Water Testers Meters

measuring range:PH: 0.00-14.00 pH

Temperature: 0.1 ° C to 60.0 °

the resolution: PH: 0.01 pH

Temperature: 0.1 ° C

precision:PH: ± 0.01 pH

Temperature: ± 0.5 ºC

automatic temperature compensation: 0 ºC -80 ºC

the battery: 3 × 1.5V (AG-13)  not including

Ambient temperature: 0 ºC -60 ºC

the standard way: automatic 2-point calibration (4.00 and 6.86 or 9.18 and 6.86)

automatic shutdown: the instrument boot, 4 minutes will automatically shut down.

 

Operation steps

 1, remove the protective cover

 2, first with distilled water pH electrode cleaning, and with the filter paper will be attached to the electrode and the surrounding moisture absorption.

 3, touch the "key", that is, turn on the power.

 4, the instrument into the measured solution, so that the measured electrode immersed in solution.

 5, gently shaking the instrument, to be read after the numerical stability of the figures in the bottom of the display read the value of the solution temperature.

 6, finished, press the "open key", turn off the power, clean the electrode with water, put on the protective cover.

 

Calibration

1, the appropriate amount of 6.86,4.00 and 9.18 standard buffer solution were poured into different clean beakers.

2, in order to calibration accuracy, for each buffer solution, with two beakers sub-installed, a beaker to rinse the electrode, the other used to calibrate the beaker. In this way, the standard buffer solution contamination can be reduced to a minimum.

3, touch the "switch" button, that is, turn on the power.

4, the electrode into the standard buffer solution pH6.86, and gently shake until the display value is stable.

5. Press and hold the "Calibration" key (in 6.86 solution) for about five seconds. The instrument will enter the auto calibration mode (the instrument can automatically recognize pH4.00 and pH6.86 standard buffer solution) until the displayed value matches the standard buffer solution. Temperature of the pH value consistent. That is to complete the pH6.86 point calibration.

6. Clean the electrode, and use the filter paper will be attached to the electrode and around the moisture absorption, into the pH4.00 standard buffer solution, and gently shake until the display value is stable.

7, long press "calibration" key (in 4.00 solution), with the operation of step 5, that is completed pH4.00 point calibration

8, clean the electrode and filter paper will be attached to the electrode and the surrounding water to dry, the electrode into the standard buffer solution pH9.18, and gently shake until the display value is stable, the display value within the allowable error range .

9, so that the calibration of the instrument is complete.

 

Note: In the following cases, the instrument must be recalibrated.

1, after the instrument has been used or placed for a long time;

2, the electrode used particularly frequently;

3, the measurement accuracy is particularly high;

Usually do not press the "calibration key" or the instrument needs to be re-

Fourth, the battery replacement

If the displayed value is fuzzy or not displayed, check the battery voltage. If the value is less than 3V, replace the battery in time.

 Replace the battery, the battery cover can be replaced, pay attention to the polarity of the battery. (Need to recalibrate after replacing the battery)




TDS Meters Pen Water Testers Meters
TDS Meters Pen Water Testers Meters

TDS Meters Pen Water Testers Meters
TDS Meters Pen Water Testers Meters



TDS Meters Pen Water Testers MetersTDS Meters Pen Water Testers Meters
Q1: Why choose Victor Instrument Meter?
A: We want to create a superior quality company and to win your trust.
 
Q2: Can I have a sample order for moisture meter?
A: Yes, we warmly welcome sample order to test and check quality.
 
Q3: Do you have any MOQ limit for moisture meter order?
A: Low MOQ, 1 PC for sample checking is available.
 
Q4: What about the lead time?
A: Sample needs 3-5 day, mass production needs about 2-3 weeks for order quantity more than one container.
 
Q5: How do you ship the goods and how long does it take to arrive?
A:Airline and sea shipping is optional. Shipping time depends on distance.
 
Q6: Is it ok to print my logo on moisture meter?
A: Yes. Please inform us formally before our production and confirm the design firstly based on our sample.
 
Q7: How about the guarantee for the products?
A: Yes. We offer one year warranty to our products.
 
Q8: How about the payment method?
A: 1.West Union or 100%TT
  2.100% irrevocable L/C at sight.
 
Q9: Can I trust Victor Instrument Meter?
A: Of course, you can trust us. More than 300 oversea customers appreciate our quality and service. With us your money in safe and your business in safe!

Thank you for visiting our website, further questions please feel free to contact us. We will do our best to support you all the time.