Products

Torch Conveyor Low Cost Nitrogen Hydrogen Hybrid High Ultra High Vacuum Furnace V8l

China Torch Conveyor Low Cost Nitrogen Hydrogen Hybrid High Ultra High Vacuum Furnace V8l, Find details about China Vacuum Furnace, Vacuum Oven from Torch Conveyor Low Cost Nitrogen Hydrogen Hybrid High Ultra High Vacuum Furnace V8l

Model NO.
V8L
Trademark
TORCH
Origin
Beijing, China
HS Code
8514109000
Model NO.
V8L
Trademark
TORCH
Origin
Beijing, China
HS Code
8514109000
Torch Conveyor Low Cost Nitrogen Hydrogen Hybrid High Ultra High Vacuum Furnace V8L

Torch Conveyor Low Cost Nitrogen Hydrogen Hybrid High Ultra High Vacuum Furnace V8l

Technical Data of Vacuum Reflow Soldering System V8:

1. Significantly reduce the welding bubbles in the solder, making the void rate as low as 1-2%.

2. Improve the electrical performance of the product and the welding joints, effectively improving the reliability of the welding point and the welding quality.

3. It can be used for double-sided welding of PCB, suitable for mass production, and can be continuously put into the production line. The production cycle is controlled at an average of 30-60S.

4. The degree of vacuum, vacuum holding time, deflation time, vacuum rate, etc. can be set freely.

5. The circuit board with aluminum heat sink can be welded.

6. Low power consumption and high heat insulation design based on the concept of environmental protection. The case temperature does not exceed 40 degrees.

7. High-efficiency and large-capacity flux recovery device.

8. Use integrated oxygen sensor technology to ensure precise control of oxygen content, and real-time/continuous monitoring of residual oxygen content in the furnace.

9. The equipment can be used as an ordinary nitrogen or air furnace at the same time.

Torch Conveyor Low Cost Nitrogen Hydrogen Hybrid High Ultra High Vacuum Furnace V8lTorch Conveyor Low Cost Nitrogen Hydrogen Hybrid High Ultra High Vacuum Furnace V8lTorch Conveyor Low Cost Nitrogen Hydrogen Hybrid High Ultra High Vacuum Furnace V8l
Technical Data of Vacuum Reflow Soldering System V8L

(Required)Technical specificationsmodel: V8L
Actual index value
Actual index valuelengthMAX 400mm
widthMAX 450mm
heightMAX 30mm
Performance parameterheating methodHot air heating
Speed adjustable range≥20cm/min
Max. heating temperatureMAX 350ºC 
heating temperature<200ppm
Heating rate range1-3ºC/s
Heating rate range1-3ºC/s
The temperature of the baked product80ºC
Heating rate range±4ºC
Number of equipment temperature zones (heating)8+1
Number of equipment temperature zones (Cooling)2
Warm-up time (heating time)According to the specific requirements of the process
Oil pump meets the demand of clean room/class 10,000Class 10,000
Class 10,000≤2mbar
Dimension/WeightDimension (m)6.3m(L)*1.55m(L)*1.7m(H)
Weight (Kg)1600kg
PowerVoltage 380V
Frequency50Hz
Power ConsumptionMaximum power 32KW
Average power 10KW
UPSOptional
Forming Gas/N2Connector Diameter 10mm
Pressure 0.3MPa-0.6MPa
Nitrogen consumption300L/min
Flow Rate 80psi(0.5Mpa, gas flow rate 80L/M)
Compressed AirConnector Diameter10mm
Pressure0.3MPa-0.6MPa
Flow Rate80psi(0.5Mpa, gas flow rate 80L/M)
ExhaustExhaust FlowMAX 8L/s
Cooling WaterConnector Diameter10mm
Flow RateInstantaneous maximum 18L/s
Instantaneous maximumDelivery cycle/week60 days
Can the delivery be delayed when the on-site installation conditions are not metYes
Technical support, training requirementsThe response time for troubleshooting at the site is within 48 hours, and training is included.Arrive at the site for 24 hours, and installation training is included.
Torch Conveyor Low Cost Nitrogen Hydrogen Hybrid High Ultra High Vacuum Furnace V8lTorch Conveyor Low Cost Nitrogen Hydrogen Hybrid High Ultra High Vacuum Furnace V8l

 

You Might Also Like