Two Piece Water Closet Semi Auto Lifting Casting Battery Producing Line with Two Layers

China Two Piece Water Closet Semi Auto Lifting Casting Battery Producing Line with Two Layers, Find details about China Sanitary Ware Toilet Ceramic Casting Line, Sanitary Ware Ceramic Toilet Casting Bench from Two Piece Water Closet Semi Auto Lifting Casting Battery Producing Line with Two Layers

Basic Info.

Model NO.

LC2-2 WC

Casting Method

Auto

Product

Two Piece Water Closet

Storage Green Base Line

Two Layers

Trademark

HEXIANG

Transport Package

Container by Sea Transport

Specification

20-30sets working mold

Origin

China

HS Code

8474809090

Model NO.

LC2-2 WC

Casting Method

Auto

Product

Two Piece Water Closet

Storage Green Base Line

Two Layers

Trademark

HEXIANG

Transport Package

Container by Sea Transport

Specification

20-30sets working mold

Origin

China

HS Code

8474809090

Product Desciption

The equipment is used to produce two-piece water closet toilet, bottom mold lifted integrally to save the producing efficiency, reducer labor strength. Every casting bench can load 18-30 sets plaster mold, every day cast 1-2 times. This machine can realize auto feeding slip, auto micro-pressure consolidate, auto return slip, improve producing pass rate. The green base storage base has two layers to save space, esay second days repairing.

Two Piece Water Closet Semi Auto Lifting Casting Battery Producing Line with Two Layers

It mainly includes:
Main frame
Lifting frame of bottom mold
Press of air belt
Hook rod
Transmission shaft
Main bench
Pneumatic unloading base carrier
Two layers store the greenwares for drying
Micro-pressure pipe system
Control system
Travel switch
Supply slip system

Parameter	Unit
Ground Line Length	M	15-30	Depends on customer capacity
Top line Length	M	15-30
Width	MM	510
Height	MM	620	Maximum Height
Length of Storage Platform	M	15-30
Width of Storage Platform	MM	645
Height of Storage Platform	MM	520
Size of Whole Line	mm	15190-32000x4400x3795	Line size only
Molds Available	set	18-40	depends on the size of the molds
Ground Incline		12
Ground Incline adjustable scale		10-14
Power	kw	2.2	Power of Main Motor
	kw	2.2
	kw	N/A	Power of Lights
	kw	N/A	Power of Fans
Air Pressure	MPa	≥0.6
Installation Ground Needed	Length(M)	3.6	3.6meter for each line
	Width(M)	4.5
	Width(M)	21+2	Minimum width needed
	Width(M)	15-30+2+3	Minimum width for casting line running

(1) Main mold closing:
Locate the clamp car and the casting bench with the bolt and clamp all the molds by rolling the clamp handle.
(2) Bottom mold closing:
Press the "Down" button to make the lifting frame decline until entire molds close completely
(3) Hooker joint:
Push the hooker position handle upward step by step and make the hooker down to inset the hook seat slot hole under the casting
bench
(4) Hold down of bottom mold:
Fill the compressed air into the air bag which will jack up the lifting frame accordingly
(5) Slip supply, slip drain and greenwares hard
(6) Loose of bottom mold:
Discharge the compressor air in air bag until completely down of lifting frame.
(7) Break-away of the hook:
The cylinder retracts to drive the hook rotating counter clockwise
(8) De-molding of bottom mold:
Press the "up/down" button to lift the hoisting frame and drive the bottom mold open slowly to avoid the green body damage caused by
strain.
(9) De-molding of the main mold:
Loose the handle of clamp carrier and extract the pin, pull the clamp carrier to the end of casting bench, pull the main mold accordingly to let the green body dry first so that assure come strength before rolling-over.
(10) Unloading and take off of base:
Turn over the molds and store the greenwares in the storage platform
(11) Green base storage line with two layers.

Two Piece Water Closet Semi Auto Lifting Casting Battery Producing Line with Two Layers