MR320E Minrry Wind Power Generation Training Equipment
Vocational Education Training Equipment Electronic Trainer DigitalI. Equipment Overview
1 Introduction
1.1 Overview
This training system simulate demo wind generate electricity process, it enable
students to learn wind generate electricity. Wind driven generator is driven by fan. This
trainer cultivate students hand on ability, it's suitable for engineering university, training
institute, technical schools.
1.2 Feature
(1)This trainer use aluminum column structure, with inner integrated measurement meters, there is universal wheels at the bottom, it's easy to move.
(2) It can do many experiment circuit and components, students can combine them to
different circuit, do different experiments and training content.
(3) Training workbench with safety protection system.
2. Performance parameter
(1) Wind power generation set: wind power generation is consisted of fan unit and air-blower unit, it adopts aluminum profile structure, the bottom of equipment is with universal wheels, the boundary dimension of fan unit is 800mm*800mm*1500mm(length× width× height), the boundary dimension of air-blower is 800mm*800mm*1500mm(length× width× height).
(2) Power box unit: aluminum profile structure, aluminum hanging box , boundary dimension 1080mm×300mm×740mm(length× width× height).
(3) Fan:
(4) Battery technical specification:
(5) Work condition:
Temperature-10~+40ºC
Temperature≤80ºC
Environment air: no corrosivity air, no fuel air, no large quantity of conductive dust
(6) Power:
3. System introduction
This system is consisted of four parts: wind power system, control system and inverter system. The wind power system is consisted of air-blower, generator and battery. Control system is made up of wind power generation controller. Inverter system is made up of frequency inverter and load unit.
Simulative wind power generator, this system adopts horizontal shaft permanent magnet synchronous generator, it adopts air-blower to simulate natural wind, air-blower can select three wind speed, this system can simulate the change of wind direction and wind power through changing the speed and location of air-blower, then it can detect the generation effect under the corresponding condition. Simulation wind power generator is as shown below.
| Input power | three phases, five wires, 380V±10% 50Hz |
| Dimension | 1600mm×800mm×1300mm(desktop type) |
| Weight | <100kg |
| Whole capacity | <1.5KVA |
| Environment temperature | -10ºC~+40ºC |
| Relative humidity | <85%(25ºC) |
3 Product composition3.1 Power control screenThe power control panel adopts aluminum alloy profile panel, closed box body structure, and the lower shelf is connected to one.3.2 Training benchThe actual training table is supported by the aluminum profile column, and the bottom wanxiang wheel brake is flexible and can be moved and positioned flexibly. The tabletop uses the high density base plate of 25mm thick, the surface high temperature and high pressure fire prevention board face treatment, complete with three guide type drawer 2, sliding door type bottom cabinet 2 pieces, the structure is firm, beautiful and generous.3.3 Power control screen configuration(1) The input of three-phase five-wire power supply, controlled by the leakage circuit breaker, has the emergency stop control button, and in case of emergency, press the emergency stop button breaker to cut off the power supply.(2) Equipped with power indicator, power output socket and secure type power supply terminal.(3) Configuration ac motor special protection switch, built-in ac power supply, short circuit protection function.(4) Built-in AC power and short circuit protection.
Power supply box, AC 1ph & 3ph and DC outputs:- 01 output variable DC 0 to 230V / 10A min, with security socket and protected by circuit breaker- 01 output variable DC 0 to 230V / 1A for rotor excitation, protected by circuit breaker- 01 output variable AC 3ph, with protected sockets, 0 to 430V + N / 5A protected by circuit breaker- 01 output constant AC 3ph, with protected sockets, 400V + N / 10A protected by circuit breaker- 04 outputs at least on single phase sockets 230V + Ground, 16A protected by circuit breakerThe box must be protected by a differential circuit breaker with high sensibility, emergency push button and key switch. It should be also protected against DC motor run-away by general cut-off, a synoptic in front illustrate the cabling drawing and light indicators which indicate voltage presence4.Equipped components(1)1 field rheostat for DC machines(2)1 starting rheostat for DC motors(3)1 rheostat for rotoric start for slip rings motor(4)1 resistive load 3ph variable by rows (by switches), having same power as the required machines (DC and AC generator)(5) 1 capacitive load 3ph variable by rows (by switches or hand wheel), having same power as the required machines DC and AC generator)(6)1 inductive load 3ph variable by rows (by switches), having same power as the required machines (DC and AC generator)(7)1 DC machine with shunt excitation, minimal power 0.75 kW, 220V, 1500 rpm can operate as motor and generator(8)1 DC machine with serial excitation, minimal power 0.75 kW, 220V, 1500 rpm can operate as motor and generator(9) 1 DC machine with combined excitation, minimal power 0.75 kW, 220V, 1500 rpm can operate as motor and generator(10)1 asynchronous motor, cage rotor 3ph, 220/380V 50Hz, 1500rpm, 0.75kW min(11)1 DAHLANDER double speed asynchronous motor cage rotor, 380V 50Hz, 0.75kW min, 1500 and 3000 rpm(12)1 synchronous reversible motor, 220/380V 50Hz, 1500rpm 0.75kW
(13)1 single phase asynchronous motor, with auxiliary pole, with starting condenser, cage rotor, 230V/50Hz, 1500rpm, 0.75kW(14)1 universal single phase motor, powered by DC and AC 230V 50Hz, 1500 rpm, 0.75kW(15)1 set of connection wires with different lengthsMachines must have the same shaft height, with didactic connection boxes having synoptic with connection schema.(16)1 brake to simulate mechanic loads, adequate speed and power for the motors, the brake allows to calculate the couple by 1 method.(17)1 board for parallel mounting of a 3ph alternator with the industrial network. The board is equipped by safety sockets and a inverter to verify frequency and voltage equality (alternator side and network side), equipped by light indicator, to verify phases correspondence and a switch to latch in case of all confirmed conditions(18)1 digital measuring module of electrical parameters, DC and AC current and voltage, single and 3ph power, the module must be protected against overload and allow to reset values to zero(19)1 digital tachymeter up to 10000 rpm provided with connection cables, allows to measure speed by contact or without contact using sensor(20)1 set of couplings with protection accessories(21)2 frame for easy mounting of the machines. Each frame allow to install two machines, and should be equipped by vibration proof rubber supports
Power supply box, AC 1ph & 3ph and DC outputs:- 01 output variable DC 0 to 230V / 10A min, with security socket and protected by circuit breaker- 01 output variable DC 0 to 230V / 1A for rotor excitation, protected by circuit breaker- 01 output variable AC 3ph, with protected sockets, 0 to 430V + N / 5A protected by circuit breaker- 01 output constant AC 3ph, with protected sockets, 400V + N / 10A protected by circuit breaker- 04 outputs at least on single phase sockets 230V + Ground, 16A protected by circuit breakerThe box must be protected by a differential circuit breaker with high sensibility, emergency push button and key switch. It should be also protected against DC motor run-away by general cut-off, a synoptic in front illustrate the cabling drawing and light indicators which indicate voltage presenceNo. | Feature Name | Details |
1 | Customer design | Yes |
2 | Warranty | 1 year, 2 years, 3 years or 5 years according to client requirements |
3 | Package | Plastic film+ carton+ Fine plywood |
4 | Products standard | International didactic equipment standard |
5 | Application range | Educational equipment for university, college, vocational training centers |
6 | Company philosophy | Supply best quality Chinese products to the worldwide schools. |
7 | Self owned brand | Shouldshine, SSEDU, JSS. |
8 | Production time | From 10 days to 60 days according to different items |
We have other laboratory as below
,such as , , ,
, such as , robot arm trainer, ,
PCB lab equipment
Food Machine Trainer