Products

Hot Sale transportation Clamp Carton Test/Testing Machine
Hot Sale transportation Clamp Carton Test/Testing Machine

Hot Sale transportation Clamp Carton Test/Testing Machine

China Hot Sale transportation Clamp Carton Test/Testing Machine, Find details about China Carton Test Machine, Clamp Carton Test Machine from Hot Sale transportation Clamp Carton Test/Testing Machine

Model NO.
HD-A534
Control
Computer Control
Weight
500-1000Kg
Power Source
AC380V
Motor
Panasonic Servo Motor
Delivery
Within 15 Days When Receive The Deposit
Base Plate Dimension
2200*2100mm
Clamping Plate Adjustable Height
0~1000mm
Device Width
Less Than 2.5m
Clamping Plate Adjustable Width
200~2000mm
Calibration Accuracy
±1% F.S
Maximum Specimen Weight
600kg
Clamping Plate Size
Height 48inch*Depth 48inch
Trademark
Haida
Transport Package
Strong Wooden Case
Specification
ASTM D642 \ ISTA 6- SAMS CLUB
Origin
China
HS Code
9024800000
Model NO.
HD-A534
Control
Computer Control
Weight
500-1000Kg
Power Source
AC380V
Motor
Panasonic Servo Motor
Delivery
Within 15 Days When Receive The Deposit
Base Plate Dimension
2200*2100mm
Clamping Plate Adjustable Height
0~1000mm
Device Width
Less Than 2.5m
Clamping Plate Adjustable Width
200~2000mm
Calibration Accuracy
±1% F.S
Maximum Specimen Weight
600kg
Clamping Plate Size
Height 48inch*Depth 48inch
Trademark
Haida
Transport Package
Strong Wooden Case
Specification
ASTM D642 \ ISTA 6- SAMS CLUB
Origin
China
HS Code
9024800000
                                                 Hot Sale Transpotation Clamp Carton Test/Testing Machine


Introduction
The Transpotation Clamp Carton Test Machine is simulated the impact strength of packaging in the real circumstance of transportation, for example, the transportation of goods. This product is applied to the scientific research institutions, colleges, packaging technique test centers, packaging material manufacturers and foreign trade or transportation departments.
  
Design Standard
ASTM D642\ ISTA 6- SAMS CLUB\ ISTA 3J
 
Technical Parameters of Transpotation Clamp Carton Test Machine: 
(The table parameters for the company Standard Model parameters, we support customer customization parameters)
Specimen shapeParallelepiped transport package
Max. Specimen weight500kg
Clamping pressure forceAccording to the transport diagram on the test sample, the operator can add 400~3000Lb (adjustable) pressure force on the corresponding surface
Clamping board sizeH*D 48*48inch
Clamping board adjustable height0~500mm
Elevation speed10~300mm/min optional
Clamping board expansion width200~2000mm
Baseboard dimensionW*D 1500*1500mm
Clamping board requirementMake sure the two clamping board are flat, parallel and non-deform under the work condition(2000Pound) and clamp board and land are vertical. Clamping board thickness no less than 25mm.
Corrector of forceForce value display used to correct clamping force
Force precisionNational standard 1.6 level
OperationManual operating rod simulates fork truck actual operating actions such as clamping control, opening, lifting up, lifting down or automatic switching mode operation (clamping board thickness no less than 25mm)
Device widthLess than 2.5m
(The table parameters for the company Standard Model parameters, we support customer customization parameters)

Clamp Compression Testing Method of Large Products 

1.Before placing the packaged product between platens, verify that the clamp force using the clamp indicator. The indicator should be placed between the axes of the platen articulation points approximately 1/2 way up the platens.
 
2.Each time the product is clamped, the force should be applied for a minimum of 15 seconds and not to exceed 1 minute.

3. Apply the clamp force on the sample with the platens resting on the floor and the front edge of the platens flush with the front of the package. If the package is too large for the clamps to be flush to front edge (i.e., large refrigerator, tractor etc.), clamp as close to the edge as possible.

4. Clamp the product a total of 10 times in the flush orientation.

5. Apply the clamp force on the packaged product with the platens in a 6×6 inch(15.2x15.2cm) offset position(see fig 5 ). Both the horizontal and vertical offset dimensions are measured at the front bottom corner of the platen. If the package is too large for the clamp to be positioned 6-inches from the front edge (i.e., large refrigerator, tractor etc.), clamp as close to this position as possible.

    1)Exception number 1: for large products with an obvious, visible external skid(see fig 6), offset clamp testing is not conducted if the product does not extend beyond any part of the skid and there is some form of handling graphic or note that indicates to clamp only from the skid. If there is no graphic or not indicating this or there is some overhang beyond the skid, then the entire clamp test protocol is conducted.

    2) Exception number 2: If the product height, when placed in its normal shipping orientation, is ≤ 12 inches, the 6 x6 inch offset testing is not conducted.

6. Clamp the product a total of 10 times with the clamp in the 6 x6 inch offset position.

7. Repeat step 5.2.5 except with a 2 x6 inch offset clamp position. The 2 x6 inch offset is similar to the 6 x6 inch offset except the platens are oriented such that they are 2-inches from the floor and 6-inches back from the package's front edge. If the package is too large for the clamps to be positioned 2-inches from the front edge (i.e., large refrigerator, tractor etc.), clamp as close to this position as possible.

8. Repeat flush and offset clamping on all other sides of the product that are indicated in the handling graphics as acceptable for clamp handling.
According to verdict standards, if there is one item failed the test, then put forward the "Test Failure Handling Sheet".

Clamp Compression Testing Method of Small Products 

Before clamp testing, verify that the clamp for using the clamp force indicator. The indicator should be placed between the axes of the platen articulation points approximately 1/2 way up the platens.
During clamp compression testing of small products, 4 samples will be utilized as outlined below.

1. If, when oriented for clamp testing (based on the handling graphics) the sides perpendicular to the platens of a single sample ≤ 24" (61cm), then the 4 sample should be placed in a"side by side"oritentation as shown to the fig 1(with 2 samples on the bottom and 2 on the top)

2. If, when oriented for clamp testing the sides perpendicular to the platens of a single sample are >24" (61cm),, then the 4 samples should be placed in a top-bottom orientation as shown fig 2. If, when placed 4-high, any of the samples are completely above the top of the platens, that sample can be removed from clamping in this orientation only(fig 3 shows 3 MHC's ready for clamp testing with the 4th sample removed from testing in this orientation)

3. Each time the samples are clamped, the force should be applied for a minimum of 15 seconds and not to exceed 1 minute.

4. Apply the clamp force on the samples with the platens resting on the floor and the samples flush with the front edge of the platens (see fig2). If the samples are too large for the clamps to be flush to front edge, clamp as close to the edge as possible.

5. Clamp the product a total of 10times with the clamps in the flush orientation.

6. Apply the clamp force on the packaged product with the platens in a 2×2 inch offset position(see fig 3). Both the horizontal and vertical offset dimensions are measured at the front bottom corner of the platen. If the package is too large for the clamps to be positioned 2-inches from the front edge, clamp as close to this position as possible.

7. Clamp the product a total of 10 times with the clamps in the offset position.

8. Repeat the flush and 2x2 inch offset camping on all other sides of the product that are identified in the handling graphics as acceptable for clamp handling. Please note, depending on the box geometry, you may use both the side-by-side and top-bottom orientation during clamp testing.

Hot Sale transportation Clamp Carton Test/Testing Machine

Why choose us? 
1. Considerate Service Different countries plugs, manually change the-voltage from 110V to 220V, insurance indicator. 
2. Excellent After sale Service: 
18 months warranty. Besides, we can help you to repair your problem controller freely, even it's not from our factory. What you need to do is to send us the controller. 
3. Commitment: 
We will sign a letter of commitment while we sign the contract, which will improve your confidence to us. 
4. Good Packaging: 
Simulation Animatronic Customer Triceratops are covered with air bubble film before put them into the wooden case, which not only has good shock absorption, impact resistance, heat sealing and also has the advantages of nontoxic, odorless, moisture corrosion, good transparency etc. 
 

You Might Also Like