Products

Transportation Package Carton Clamping Testing Machine

China Transportation Package Carton Clamping Testing Machine, Find details about China Package Clamping Tester, Carton Clamping Force Tester from Transportation Package Carton Clamping Testing Machine

Model NO.
HD-A534
Control
Computer Control
Weight
500-1000Kg
Power Source
AC380V
Delivery
Within 15 Days When Receiving The Deposit
Maximum Specimen Weight
600kg
Motor
Panasonic Servo Motor
Power
380V/ 50Hz
Device Width
Less Than 2.5m
Calibration Accuracy
±1% F.S
Clamping Plate Adjustable Height
0~1000mm
Clamping Plate Size
Height 48inch*Depth 48inch
Base Plate Dimension
2200*2100mm
Trademark
Haida
Transport Package
Strong Wooden Case
Specification
ASTM D642 \ ISTA 6- SAMS CLUB
Origin
China
HS Code
9024800000
Model NO.
HD-A534
Control
Computer Control
Weight
500-1000Kg
Power Source
AC380V
Delivery
Within 15 Days When Receiving The Deposit
Maximum Specimen Weight
600kg
Motor
Panasonic Servo Motor
Power
380V/ 50Hz
Device Width
Less Than 2.5m
Calibration Accuracy
±1% F.S
Clamping Plate Adjustable Height
0~1000mm
Clamping Plate Size
Height 48inch*Depth 48inch
Base Plate Dimension
2200*2100mm
Trademark
Haida
Transport Package
Strong Wooden Case
Specification
ASTM D642 \ ISTA 6- SAMS CLUB
Origin
China
HS Code
9024800000
Transpotation Package Carton Clamping Testing Machine


Introduction
Transportation Package Carton Clamping Testing Machine is simulated the impact strength of packaging in the real circumstance of transportation, for example, the transportation of goods. This product is applied to the scientific research institutions, colleges, packaging technique test centers, packaging material manufacturers and foreign trade or transportation departments.
 
Design Standard
ASTM D642\ ISTA 6- SAMS CLUB\ ISTA 3J
  
Technical Parameters of Transportation Package Carton Clamping Testing Machine: 
 
ItemDescription
Max. Force400~3000Lb
Maximum specimen weight600kg (can be customized)
Load cell4 load cell for highest accuracy
Control system Touch screen controller, Windows 7, RS-232 interface
MotorPanasonic servo motor w/ DC variable speed drive system, high-precision mechanical ball screw rod
Force reading kgf, Ibf, N, KN, T etc
Load cell Resolution1/250,000
Load Precisionwithin ±0.25%
Parallelism of Platens Parallel within ±2.5mm
Clamping plate sizeHeight 48inch X depth 48inch
Clamping plate adjustable height0~1000mm
Clamping plate adjustable width200~2000mm
Base plate dimension2200 X 2100mm
Test speed0.25-2.5mm/sec (according ISTA 6- SAMS CLUB)
Software TM 2101
Data displayLoad, displacement, speed, loading rate and elapsed time
FunctionThe clamp can be up and down
Clamping plate requirementMake the two clamping boards flat and non-deform under work condition (2000 Pounds) and make clamping boards' parallel and clamping board and land vertical. Clamping board is thicker than 25mm.
Safety features E-Stop
Over-load protection
Upper and lower limit switches
Load sensor with automatic retreat
(The table parameters for the company Standard Model parameters, we support customer customization parameters)

Clamp Compression Testing Method of Large Products 

1.Before placing the packaged product between platens, verify that the clamp force using the clamp indicator. The indicator should be placed between the axes of the platen articulation points approximately 1/2 way up the platens.
 
2.Each time the product is clamped, the force should be applied for a minimum of 15 seconds and not to exceed 1 minute.

3. Apply the clamp force on the sample with the platens resting on the floor and the front edge of the platens flush with the front of the package. If the package is too large for the clamps to be flush to front edge (i.e., large refrigerator, tractor etc.), clamp as close to the edge as possible.

4. Clamp the product a total of 10 times in the flush orientation.

5. Apply the clamp force on the packaged product with the platens in a 6×6 inch(15.2x15.2cm) offset position(see fig 5 ). Both the horizontal and vertical offset dimensions are measured at the front bottom corner of the platen. If the package is too large for the clamp to be positioned 6-inches from the front edge (i.e., large refrigerator, tractor etc.), clamp as close to this position as possible.

    1)Exception number 1: for large products with an obvious, visible external skid(see fig 6), offset clamp testing is not conducted if the product does not extend beyond any part of the skid and there is some form of handling graphic or note that indicates to clamp only from the skid. If there is no graphic or not indicating this or there is some overhang beyond the skid, then the entire clamp test protocol is conducted.

    2) Exception number 2: If the product height, when placed in its normal shipping orientation, is ≤ 12 inches, the 6 x6 inch offset testing is not conducted.

6. Clamp the product a total of 10 times with the clamp in the 6 x6 inch offset position.

7. Repeat step 5.2.5 except with a 2 x6 inch offset clamp position. The 2 x6 inch offset is similar to the 6 x6 inch offset except the platens are oriented such that they are 2-inches from the floor and 6-inches back from the package's front edge. If the package is too large for the clamps to be positioned 2-inches from the front edge (i.e., large refrigerator, tractor etc.), clamp as close to this position as possible.

8. Repeat flush and offset clamping on all other sides of the product that are indicated in the handling graphics as acceptable for clamp handling.
According to verdict standards, if there is one item failed the test, then put forward the "Test Failure Handling Sheet".

Clamp Compression Testing Method of Small Products 

Before clamp testing, verify that the clamp for using the clamp force indicator. The indicator should be placed between the axes of the platen articulation points approximately 1/2 way up the platens.
During clamp compression testing of small products, 4 samples will be utilized as outlined below.

1. If, when oriented for clamp testing (based on the handling graphics) the sides perpendicular to the platens of a single sample ≤ 24" (61cm), then the 4 sample should be placed in a"side by side"oritentation as shown to the fig 1(with 2 samples on the bottom and 2 on the top)

2. If, when oriented for clamp testing the sides perpendicular to the platens of a single sample are >24" (61cm),, then the 4 samples should be placed in a top-bottom orientation as shown fig 2. If, when placed 4-high, any of the samples are completely above the top of the platens, that sample can be removed from clamping in this orientation only(fig 3 shows 3 MHC's ready for clamp testing with the 4th sample removed from testing in this orientation)

3. Each time the samples are clamped, the force should be applied for a minimum of 15 seconds and not to exceed 1 minute.

4. Apply the clamp force on the samples with the platens resting on the floor and the samples flush with the front edge of the platens (see fig2). If the samples are too large for the clamps to be flush to front edge, clamp as close to the edge as possible.

5. Clamp the product a total of 10times with the clamps in the flush orientation.

6. Apply the clamp force on the packaged product with the platens in a 2×2 inch offset position(see fig 3). Both the horizontal and vertical offset dimensions are measured at the front bottom corner of the platen. If the package is too large for the clamps to be positioned 2-inches from the front edge, clamp as close to this position as possible.

7. Clamp the product a total of 10 times with the clamps in the offset position.

8. Repeat the flush and 2x2 inch offset camping on all other sides of the product that are identified in the handling graphics as acceptable for clamp handling. Please note, depending on the box geometry, you may use both the side-by-side and top-bottom orientation during clamp testing.

Transportation Package Carton Clamping Testing Machine

Transportation Package Carton Clamping Testing Machine

Our Company

Haida products are widely used in paper products, packaging, ink printing, adhesive tapes, bags, footwear, leather products, environment, toys, baby products, hardware, electronic products, plastic products, rubber products and other industries, and are applicable to all scientific research units, quality inspection institutions and academic fields. Our products meet UL, ASTM, JIS, GB,SO, TAPPI, EN, DIN, BS and other domestic and international standards.

Packaging & Shipping:
Simulation Animatronic Customer Triceratops are covered with air bubble film before put them into the wooden case, which not only has good shock absorption, impact resistance, heat sealing and also has the advantages of nontoxic, odorless, moisture corrosion, good transparency etc.

Transportation Package Carton Clamping Testing Machine

Customer Feedback

Transportation Package Carton Clamping Testing Machine
FAQ:
 
Q:Are your company a trading one or a factory?
A:Factory + trade (integration),More than 12 years focusing on test equipment field,6 years exporting experience.

Q:After an order is placed, when to deliver?
A:Generally about 10-25days, If we have inventory, we can arrange shipment within 3 days.
Please be aware that our production lead times depend on specific items and item quantities.

Q:What about the product' services and quality?
A:Each equiopment must be carried out 100% quality examination and test when shipping and delivery goods. Product use training, each of our product provide video training to show you how to install & operate. We can arrange engineer to train the operation of equipment to customer's company when you need. products are widely recognized and trusted by users.
A :Considerate Service Different countries plugs, manually change the-voltage from 110V to 220V, insurance indicator.

Q: Can your products be customized?
A: Yes, our product can be customized according to your parameters.
 

You Might Also Like