Products

Laser Scan Head Laser Source Laser Spare Parts Laser Marking Control Card for Laser Manufacturer

China Laser Scan Head Laser Source Laser Spare Parts Laser Marking Control Card for Laser Manufacturer, Find details about China Lmcv4-Fiber-M, Control Board from Laser Scan Head Laser Source Laser Spare Parts Laser Marking Control Card for Laser Manufacturer

Model NO.
LMCV4-FIBER-M
Origin
China
HS Code
8466939000
Model NO.
LMCV4-FIBER-M
Origin
China
HS Code
8466939000
Laser Scan Head Laser Source Laser Spare Parts Laser Marking Control Card for Laser Manufacturer

1. Feature:
Standard DB25 connector, can be wire to IPG laser directly.
Galvo control signal is digital, which can be connect to most scanhead directly.
Multiple boards on 1 computer: One computer can control up to 8 control board to mark different pattern simultaneously
Extension axis(step motor or sever motor): two set of direction/pulse signal can be used to control 2 step(server) motors.
6 general input signals(TTL campatible): In0-In3, XORG0(IN14), IN15.
2 general output signals(TTL campatible): OUT4-OUT5 coming out of Con4.
Remark function: this function is used to remark what ever is in the memory of the board, especially convenient for high speed marking of a same pattern.
Compatible with USB2.0 specifications.

2. Main Structure Size
Laser Scan Head Laser Source Laser Spare Parts Laser Marking Control Card for Laser Manufacturer



3. Case:
Fiber Laser Marking Machine.

4. Electrical Wiring-Pin Definition
4.1 power supply
The control board need a 5V DC power supply. We recommend a 5V/3A DC supply. The Vcc and Gnd pin are 4/5 and 12/13 of CON4 respectively. You may find in other connectors some Vcc/Gnd pins, but we strongly suggest you use the ones in CON4.
CON4 pinsNamefunction
4, 5VCC+5V power supply.
12,13GNDReference ground of the power supply.

4.2  CON1: DB15 scan head control

The signals that control scanhead are digital, therefore can be connected to the digital scan head directly. Because the protocols that every manufacturer used are not always the same, you need to conform which protocol is used. We also provide a D/A converter in the package. The digital signal converted by which can be connected to a analog scan head.
Laser Scan Head Laser Source Laser Spare Parts Laser Marking Control Card for Laser Manufacturer
 
PinNameFunction
1,9CLK- / CLK+Clock signal- / Clock signal+
2,10SYNC- / SYNC+Synchronization  signal   - / Synchronization
signal+
3,11X Channel- / X Channel+Scan head signal X- / Scan head signal X+
4,12Y Channel- / Y Channel+Scan head signal Y- / Scan head signal Y+
5,13Z Channel- / Z Channel+Scan head signal Z- / Scan head signal Z+
6,14,Status-/Status+Reserved
7NULLReserved
8,15GNDReference signal
To a commonly used two dimension scanhead, connecting CLK, SYNC, four wires for XChannel and Ychanne and the GND would be enough. We recommend a shielded twisted pair  for all digital signal.

4.3 CON2 :DB25 Laser Control
CON2 socket can be connected to the DB25 connector through a pin to pin cable.Laser Scan Head Laser Source Laser Spare Parts Laser Marking Control Card for Laser Manufacturer
Pin No.SignalIllustration
1--8P0--P7Laser power signal.TTL compatible
9PLATCHPower signal latch. TTL compatible.
10, 14,GNDThe reference ground of the control board.
11,12,16,21LASERST0~3Alarm signal of Laser module
17VCC5V power output.
18MOMain oscillator signal. TTL compatible.
19APPower amplifier signal. TTL compatible.
20PRRPulse repetitive rate signal. TTL compatible.
22RedPtRed light pointer signal. TTL compatible.
23EMSTOPEmergency stop signal. TTL compatible.
13, 24, 25 Unconnected.
 
4.4 CON3: DB9 On-the-fly interface
Laser Scan Head Laser Source Laser Spare Parts Laser Marking Control Card for Laser Manufacturer
PinNamefunction 
1IN8Input port 8Form a closed circuit with GND

2,6
IN9+,IN9-
Input port 9		With a 1K resistor built in. if the
input signal is over 12V, an external resister is recommended.
3,7BCODEP/ BCODENEncoder input B+/B- 
4,5ACODEP/ACODENEncoder inputA+/A- 



8


VCC


+5V output		This is a power supply for external device. DO NOT CONNECT POWER SUPPLY HERE OR SHORT IT WITH GND. OTHERWISE IT WILL CAUSE
DAMANGE OF THE BOARD.
9GNDReference ground 
4.5 DB15 Power Supply and Extension axis control
Laser Scan Head Laser Source Laser Spare Parts Laser Marking Control Card for Laser Manufacturer
PinNAMEFunction

1
XORG0		The home signal of extension axis X. To use this pin just
connect it and GND to a switch. In software In14 represents this pin.
2GIN15General input in15, using GND as a reference ground.
2,10OUT4, OUT5General Output Out 4-Out 5, using GND as reference ground.
They are all TTL output .
4,5VinInput pin for 5V power supply.
11,12,13GndReference ground of 5V power supply

14
XDIR+		Direction signal of extension  axis X. It is a TTL output. For common anode, use VCC and XDIR+ signals, and VCC is
anode signal.

15
XPUL+-		Pulse signal of extension axis X. It is a TTL output. For
common anode, use VCC and XDIR+ signals, and VCC is anode signal.


8

ReMark		Repeat marking signal. Use GND as a reference ground, to use this signal just connect a switch between this pin and GND. When it is activated the control will mark the content in the cache.
4.6 CON5: Digital IOLaser Scan Head Laser Source Laser Spare Parts Laser Marking Control Card for Laser Manufacturer
pinnamefunction
1,2,4,Out0--7General Output Out 0 - Out 7, using GND as reference ground. They are all TTL output by default. Out 4-Out 7 can be configured to perform as a OC out put by jumper
JP8-11.
5,14,15,
16,17


3		 
COM
OC output, connect it to plus end of the pull power(for example 24V), in case of the output circuit will be
wracked by inductiveload(for example: inductive relay)
18LaserErrOC output, if there is output, means laser has problem,
then this signal will be pull to GND.
6,7,8,19,20GNDReference ground of control board.
21INRTN1Minus input of general input 10/11
9,22GIN10,GIN11Plus input of general input 10/11, make up return circuit
with INRTN1.
10INRTN2Minus input of general input 12/13
23,11GIN12,GIN13Plus input of general input 12/13, make up return circuit
with INRTN2.
12,13,24,25Gin4--7General input in4-in7, using GND as a reference ground.

5. Related Products
5.1 Laser Source: Raycus/ MAX/ IPG
Laser Scan Head Laser Source Laser Spare Parts Laser Marking Control Card for Laser Manufacturer
 
5.2 Galvanometer Scanner: SINO-GALVO
Laser Scan Head Laser Source Laser Spare Parts Laser Marking Control Card for Laser Manufacturer
5.3 Field Lens: WAVELENTH
Laser Scan Head Laser Source Laser Spare Parts Laser Marking Control Card for Laser Manufacturer
5.4 Rotary Device (If need)
Laser Scan Head Laser Source Laser Spare Parts Laser Marking Control Card for Laser Manufacturer6. Contact Information
 

To be continued..

You Might Also Like