Acrylic Polymer Polyurethane Protective Finishing 210t Polyester Oxford Fabric with PU Waterproof Coating1.Pictures of product
The colour can customized as requirement 2.Characteristics High adaptability to wet and dry base layer, not flowing on elevation
Pigment can be added as you wish
High elasticity and high durability.
Poison-free and odor-free, no pollution, easy construction, short in construction time.Ventilation property, no blistering even on wet base layer.
Grade I/II:Tensile strength / MPa >= | 1.90 |
Elongation at break / % >= | 550 |
Tearing strength/(N/mm) >= | 12 |
Foldability at low temperature / ºC <= | -40ºC |
Watertightness 0.3MPa 30min | Water resistant |
Solids content / % >= | 80 |
Surface drying time / h <= | 12 |
Hard dring time / h <= | 24 |
Heating expansion rate / % | <= | 1.0 |
| >= | -4.0 |
Aging property | Heat aging | No crack and deformation |
| Artificial weathering aging | No crack and deformation |
Tensile strength / MPa >= | 2.45 |
Elongation at break / % >= | 450 |
Tearing strength/(N/mm) >= | 14 |
Foldability at low temperature / ºC <= | -40ºC |
Watertightness 0.3MPa 30min | Water resistant |
Solids content / % >= | 80 |
Surface drying time / h <= | 12 |
Hard dring time / h <= | 24 |
Heating expansion rate / % | <= | 1.0 |
| >= | -4.0 |
Aging property | Heat aging | No fault and deformation |
| Artificial weathering aging | No fault and deformation |
3.Advantage
1.This product is a color, no-tar,double(single) components waterproof coating.
2.Cold construction, simple technology ,convenient maintenance, can be at room temperature for flat roof and all kinds of complex parts for construction.
3.Overall Good forming, no seams, with rubber elasticity, high elongation, fully able to adapt to the base of the crack and deformation.
4.High bonding strength, wide application range, can be used in the water, is an ideal material for level of waterproof.
5.Long service life, weather resistance, aging resistance, oil resistance, acid and alkali resistance,and stable performance.
4.Application This product applies to masonry, mortar, concrete, metal, wood, hard plastic, glass, plasterboard, foam board, asphalt, rubber, SBS, APP, polyurethane and civil construction( such as building, wall surface, subsurface, tunnel, bridge, pool, reservoir, bathroom and kitchen).
Roof: concrete flat, sloping roof, roof gutter, awning and all kinds of irregular shape of the roof
Underground construction: concrete interior wall, external wall, floor, elevator pit, underground tunnel, cable wells, pipe
outside waterproof.
Ground construction: toilet, kitchen, Roof garden, reservoir, swimming pool, dressing, bridge etc.
Joint: expansion joint, construction joint, settlement joint, wall pipe, wateroutfall
5.Construction Requirement
Basic requirements rigid smooth without sundry, interna angle and external angle to make circular arc, the diameter of internal angle greater than 50mm, the diameter of external angle ia more than 10mm
Large waterproof construction: hybrid coating rubber or plastic scraper uniform coating for thickness is consistent, general of 1.5 mm to 2.0 mm, appropriate is three to four times after brush, brush time should be in previous besmear brushs curing film, and the vertical direction is generally brushed, separate film, underground engineering floor should increase spread a layer of fetal body reinforcing material.
Coating thickness: underground engineering 1.2 2.0 mm, the general should be 1.5 mm, lavatory bath room should not be less than 1.5 mm, exposed roof engineering using multichannel waterproof, each thickness not less than 1.2 mm, the waterproof grade III roof a fortification, waterproof thickness not less than 2 mm, between the coating and spread tire body reinforced material, tire body the following coating thickness not less than 1.0 mm, top coating not less than 0.5 mm
Act the role of facing construction: in the brush real last side coating not before curing surface dilute and clean grains of sand
Cover: coated membrane surface should be according to the design requirements for isolation protection.

6.Attention:
Remove the water, oil, dirt on the base before use;
Bonding base surface should be dry, moisture content 8%;
Tape should be stored in dry and shade places, avoid heat source, avoid direct sun and rain
The product is self-adhesive materials, should stick on the right place in one time, unfavorable to reuse;Forspecial use tape, please contact us
7.General painting construction method, this method is suitable for the overall waterproofing of roofs, exterior walls, etc., as well as the construction of small cracks and cracks. It can be used immediately after opening the cover, and the construction is simple
8.Repairing large cracks, expansion joints, etc. This method is suitable for waterproofing and repairing large cracks in the roof, expansion joints and the joints of buildings.
9.The cured film is smooth and free of impurities
10.Packing and delivery
11. Why choose us?
12.Please contact us