Smsr Similar Series Hxgf Ratio 20 Conveyors Shaft Mounted Helical Gear Reducer

China Smsr Similar Series Hxgf Ratio 20 Conveyors Shaft Mounted Helical Gear Reducer, Find details about China Reducer, Shaft Mounted from Smsr Similar Series Hxgf Ratio 20 Conveyors Shaft Mounted Helical Gear Reducer

Type
Cylindrical Gear Box
Ratio
5/13/20
Origin
China
HS Code
8483409000
Type
Cylindrical Gear Box
Ratio
5/13/20
Origin
China
HS Code
8483409000
Name:Parallel shaft helical shaft mounted gear reducer
Smsr Similar Series Hxgf Ratio 20 Conveyors Shaft Mounted Helical Gear Reducer
Smsr Similar Series Hxgf Ratio 20 Conveyors Shaft Mounted Helical Gear Reducer


Models:HXGF30,HXGF40,HXGF50,HXGF55,HXGF65,HXGF75,HXGF85,HXGF100

Hengfengtai Shaft Mount Reducers HXGF series are manufactured in eight gear case sizes, from 30 to 100, nominal gear ratios are 5: 1, 13: 1 and 20:1. A very wide choice of final driven speeds can be determined by the use of an appropriate input Wedge Belt Drive.
The units will normally be oil lubricated, but they are equally suitable for long life synthetic lubricants.

Dimension

Flange Mounted
Smsr Similar Series Hxgf Ratio 20 Conveyors Shaft Mounted Helical Gear Reducer
 
Shaft Mounted
Smsr Similar Series Hxgf Ratio 20 Conveyors Shaft Mounted Helical Gear Reducer


Installation
Satisfactory performance depends on proper installation lubrication and maintenance. Therefore it is important that the instructions in the installation and maintenance leaflet,supplied with each gearbox, are followed carefully. Some of the important aspects of belt and torque-arm installation are listed below.

1. Install pulley on gearbox input shaft as close to the reducer as possible, and mount reducer on driven shaft as close to bearing as practical See Figure 1. Failure to do this will cause excess loads in the input shaft bearings and output bearings and could cause their premature.
2. Install motor and wedge belt drive with the belt pull at approximately 90 to the center line between driven and input shafts(See Fig. 2). This will permit tensioning of the wedge belt drive with the torque arm which should preferably be in tension. If output hub runs anti-clockwise,torque arm should be positioned to the right( See Fig 3)
3. Install torque-arm fulcrum on a rigid support so that the torque-arm will be at approximately right angles to the center line through the driven shaft and the torque arm case bolt(See Fig 4). Make sure there is sufficient take up in the turnbuckle for belt tension adjustment.


Smsr Similar Series Hxgf Ratio 20 Conveyors Shaft Mounted Helical Gear Reducer
Mounting Poisition
Smsr Similar Series Hxgf Ratio 20 Conveyors Shaft Mounted Helical Gear Reducer
Oil temperature (ºC)Oil change interval (h)
Mineral OilSynthetic Oil
<65800025000
65-80400015000
80-95200012500
 
Products benefits: 

1. High efficiency
2. Small volume 
3. strong capacity of being overloaded
4. Long service life 
5. Anti-leaking oil 
6. simple structure and convenient to be installed and maintained 
7. Widely application 

Description:
TA series HXGF shaft mounted gear reducer, made by Zhejiang Hengfengtai Reducer Mfg. Co., ltd, was wildly used in mechanical transmission fields such as agriculture, telecommunications industry, food industry, tobacco industry, automotive industry, cement industry, mining industry, tourism industry and so on.
Our TA series HXGF shaft mounted helical gear reducer provides a convenient installation and removal method for speed reduction by mounting directly on the drive shaft. The TA series HXGF shaft mounted helical gear reducer features carburized gear teeth with optimal gear geometry and wide gear faces, allowing maximum loading and highest efficiency torque output, for higher rating capacity in the most compact design.

Benefits:
Higher rating with a 25° Pressure angle and wider gear teeth face for maximum torque
Heavy duty roller bearings for maximum strength and extended life
Flexible motor mounting capabilities
Backstops with centrifugal lift-off sprags to maximize reliability

Maintenance:
After 300-hour operation, please change the oil, and flush the gear unit with suitable detergents.
Pls do not mix the mineral oil and synthetic oil.
Pls check the oil level in regular time.

Applications:
Perfect for screw conveyors, belt conveyor bulk handing machinery and process equipment for:
Baggage handing
Pulp, paper, and forestry
Aggregate and mining
Mixers and process equipment
Grain and agriculture
Model(single/double)HXGF30HXGF40HXGF50HXGF55HXGF65HXGF75HXGF85HXGF100
Nm(100rpm)256277401468632783983119414441881240729703457438059407449

Smsr Similar Series Hxgf Ratio 20 Conveyors Shaft Mounted Helical Gear Reducer

Description:

 

SMSR Similar Series HXGF Ratio 20 Shaft Mounted Helical Gear Reducer For Conveyors are in good quality.


WARRANTY:

18 Months Quality Guarantee


Specifications:




Applications:

SMSR Similar Series HXGF Ratio 20 Shaft Mounted Helical Gear Reducer For Conveyors

 

 


 

Products Benefits:

 

1. Higher rating with a 25°pressure angle and wider gear teeth face for maximum torque

 

2. Heavy duty roller bearings for maximum strength and extended life

 

3. Flexible motor mounting capabilities

 

4. Backstops with centrifugal lift-off sprags to maximize reliability
 

Competitive Advantage:

 

1.HFT total registered capital in RMB 58,000,000.We had 2 sub companies located in Binghai&Sanxi Industry Zone, covering area 50000 square meters and 350 staff so far.

 

2.There are more than 40 professional technical engineers and 49 items patents we have.

 

3.Relying on high quality products and perfect service, our products have been successfully appliedby more than 5000 customers.

Smsr Similar Series Hxgf Ratio 20 Conveyors Shaft Mounted Helical Gear ReducerSmsr Similar Series Hxgf Ratio 20 Conveyors Shaft Mounted Helical Gear Reducer