Products

Steel Wire Rope, Steel Wire Rope Die Casting Machine, Vertical Die Casting Machine, Steel Wire Zinc Die Casting Machine

China Steel Wire Rope, Steel Wire Rope Die Casting Machine, Vertical Die Casting Machine, Steel Wire Zinc Die Casting Machine, Find details about China Die-Casting Machine, Wire Rope Die Casting Machine from Steel Wire Rope, Steel Wire Rope Die Casting Machine, Vertical Die Casting Machine, Steel Wire Zinc Die Casting Machine

Model NO.
CLY-YZJ810
Trademark
CLY
Transport Package
Wooden Box
Specification
350KG
Origin
Guangzhou
Model NO.
CLY-YZJ810
Trademark
CLY
Transport Package
Wooden Box
Specification
350KG
Origin
Guangzhou
Professional manufacture of wire rope die casting machine, wire rope die casting machine, brake wire die casting machine, zinc head die casting machine, small die casting machine, wire rope patterning machine, widely used in pendant lamps, brake wires, various spreaders, etc. ~ 15 bars, weight up to 200g, high safety, fast speed, less burr, high efficiency, convenient and fast output.Steel Wire Rope, Steel Wire Rope Die Casting Machine, Vertical Die Casting Machine, Steel Wire Zinc Die Casting Machine


Machine size (length, width and height): 1.5 * 0.9 * 1.8 (m)
A complete action of the machine: 5S
The new machine is equipped with a set of die-casting molds

Method usage considerations

Power supply voltage: three-phase four-wire, voltage 380V / 50Hz, voltage fluctuation range ± 10%
Control voltage: DC24V
Before installing, operating and maintaining
Read this instruction manual and all accompanying materials of other related equipment to correctly use
use. Please familiarize yourself with all knowledge, safety information, and notes about the equipment
Use after notice
Please follow the content of this manual to make correct settings.
Do not set in the following environment. Places exposed to direct sunlight
• Locations where the ambient temperature and relative humidity exceed the specification value range • Locations where temperature changes rapidly and condensation may occur
Places with corrosive gas and flammable gas Places with a lot of dust, dust, salt and iron powder
Places where splashes of water, oil, medicines, etc. can be splashed
Shielding measures must be taken when using in the following environment. Places where interference caused by static electricity
A place that generates a strong electric field and a strong magnetic field A place that may be exposed to radiation

Before turning on the power
Please pay attention to the following points when the power is turned on initially.
• Check if there is any wiring debris attached to the construction, especially conductive objects.
• Check the power supply wiring, input / output wiring, and power supply voltage for errors.
• Tighten the mounting screws and terminal screws firmly.
• Only specially trained personnel can operate this equipment.
• When operating the machine, all safety protection devices must not be removed or opened without authorization.
• Pay attention to safety during commissioning and use. Do not touch the movement when the machine is turned on.
Electrical parts.
• Do not leave your post while the equipment is working. In case of emergency, please press the following immediately
The red emergency stop button on the board, or the main power switch of the electric control cabinet.
• Reset, in manual state, only when there are no people around when operating manual.


• In the automatic state, the machine cannot start running without being in place.
• After the emergency stop on the operation box is opened, the reset exception is released to start the ready operation.
• After every week of operation, the linear guide rail must be lubricated and cleaned.
• All travel switches, sensor switches, proximity switches and system users on the machine
The parameters have been adjusted before leaving the factory except for instructions. It is strictly forbidden to adjust randomly, otherwise
It may cause unpredictable consequences at any time.
• It is strictly forbidden to switch on and off frequently
• Inspection and re-tightening of fastening parts ... due to vibration, temperature changes, etc.
Factors, screws and bolts are easy to loose, please check whether they are tight,
And if necessary, re-tighten.
• Whether the conductors and insulating materials are corroded or damaged, and whether there is abnormal vibration or abnormality
Often sound.
• All lines of the equipment must not be changed randomly during use, without
With the permission of the manufacturer, you can change the circuit of the equipment at random.
And after-sales maintenance, the producer will not be responsible.
• When performing installation, wiring, etc., be sure to disconnect all power sources externally
It can be operated only afterwards. Otherwise, there is a risk of electric shock or product damage.
• When cleaning and tightening the terminals, be sure to disconnect all external
Operate after the power supply.
If you operate with the power on, there is a danger of electric shock.
The examples in this book, technical materials, samples, etc. are for reference,
Action is not guaranteed. When selecting, please confirm the function and safety of the machine and device by yourself before use.
Please read the manual of this book and related products, hoping to fully understand its specifications
The correct use of the product under the premise.
In short, I hope this manual will be delivered to the end user.
1. During the operation of the equipment, any part of the body shall not extend into the area directly above the equipment;
2. Before maintenance, you must press the emergency stop button until the maintenance is completed before resetting;
3. When someone is shutting down for maintenance, it is forbidden for anyone to touch the operation buttons and the switching power supply.
 

You Might Also Like