Products

120 Speed Steam Heating Automatic Corrugated Single Facer Line, 2 Ply Single Facer Line

China 120 Speed Steam Heating Automatic Corrugated Single Facer Line, 2 Ply Single Facer Line, Find details about China Single Facer Machine, 2 Ply Single Facer Line from 120 Speed Steam Heating Automatic Corrugated Single Facer Line, 2 Ply Single Facer Line

Model NO.
WJ-120-1800
Trademark
HRB PACK
Specification
WJ-120-1800
Origin
China
HS Code
84413090
Model NO.
WJ-120-1800
Trademark
HRB PACK
Specification
WJ-120-1800
Origin
China
HS Code
84413090
WJ-120-1400 CORRUGATED SINGLE FACER LINE
120 Speed Steam Heating Automatic Corrugated Single Facer Line, 2 Ply Single Facer Line
WJ-120-1400 CORRUGATED SINLGE FACER LINE
1HYDRAULIC MILL ROLL STAND 2 SET
2Paper trolley4 SET
3290S SINGLE FACER E FLUTE 1 SET
4290S SINGLE FACER F FLUTE 1 SET
5Conveyor bridge1 SET
6ELECTRIC slitting and NC cutting machine1 SET
7AUTO UP DOWN STACKER 1 SET
8GLUE KITCHEN 1 SET

main technical parameters and requirements in production line
type:WJ-120-1400 single corrugated cardboard production line:
1.MAX. Produce width:1400mm  design speed:120m/min   Economic speed:70-100m/min
note:Production line speed test paper should meet the following requirements:(Equipment surface temperature not lower than 172 ºC above)
Paper grade of not less than B grade Paper moisture content of about:11%±2%
Facial tissue:100-250g/m2           core paper:100--180g/m2
Flute-type combination:A ,C, B, E(Or a choice by the customer)
Steam about500Kg/Hr, Maximum pressure:1.2Mpa,Common pressure:0.8-1.1Mpa
6,Power supply:380V/415V     50Hz         Three-phase four-wire system
7,equipment installed total power:about 90KW    Actual electric consumption:about30KW
8,Equipment area:about 30m×11m×5m(Specific length of foundation Figure prevail)
9,Equipment out of paper orientation:according to user's factory to determine  drive left or right
10,Equipment applicability,Available in A, B, C class domestic or imported paper.

Customer-owned section
1, steam heating system:proposal with 1000Kg / Hr of a steam boiler    pressure:1.25Mpa    steam pipeline.
2,air compressed machine,air pipeline,glue conveying pipe.
3, power supply,wires connected to the operation panel and line pipe.
4, water sources,water pipelines,buckets and so on.
5,Water, electricity, gas flush mounting civil foundation.
6,Test with the base paper,corn starch (potato),Industrial use caustic soda,borax and other material.
7, Oil equipment,lubricating oil,hydraulic oil,lubricating grease.
8, installation,commissioning of food, accommodation.And provide installers with the installation.



ZJ-V5B hydraulic shaftless mill roll stand
120 Speed Steam Heating Automatic Corrugated Single Facer Line, 2 Ply Single Facer Line

structural feature: 
★adopt hydraulic drive to complete the paper clamping, loosen, remove for the medium, translation left and right and others,the lifting of the paper adopts hydraulic drive.
★brake adjustable adopts multipoint braking system.

  
technical parameters:
1,the range of clamping paper:MAX1400mm MIN1000mm  2,clamping diameters:MAX¢1500mm MIN¢350mm
3,main shaft diameter of paper holder:¢242mm    4,gas source work pressure(Mpa):0.4---0.8Mpa
5,equipment size:Lmx4.3*Wmx1.8*Hmx1.6              6,single weight:MAX4000Kg
Hydraulic system parameters:
  1. Work pressure(Mpa):16---18Mpa                2,lifting hydraulic cylinder:¢100×440mm   
  1. Clamping hydraulic cylinder:¢63×1300m 4,hydraulic station motor power:3KW     
5,solenoid valve voltage:220V  50 Hz
Mainly purchased parts, raw materials and origin:
Name of main partsBrands or place of originmaterial
Main shaftDay steel productiondiameter242mm
Swing armProduction by ownResin sand gray ironHT200
wallboardJigang prductionQ235AWelding parts
bearingHRB,ZWZ,LYC 
expand chuckZhejiang xusheng3,4inch shared
Main electrical applianceFrance Schneider 
buttonCHINT NP2series 
Air switchFrench Schneider 
Pneumatic componentsZhejiang Sonor CSM 
Hydraulic stationShandong zaozhuang 
Brake pumpzhejiang 

paper trolley, track

structural feature:
★the whole track buried,The main frame of the 14th Channel steel with ¢ 20mm cold drawn welded round,length of track 4510mm.
★each paper holder matched two sets paper trolley, and paper on both sides at the same time.pull the roller paper to the right place.
Mainly purchased parts, raw materials and origin:
Name of main partsBrands or place of originmaterial
track and paper carTanggang or jigangNO14channel steel,Q235A,steel strip
bearingHRB,ZWZ,LYC 

SF-290s single surface adsorption machine
120 Speed Steam Heating Automatic Corrugated Single Facer Line, 2 Ply Single Facer Line

Structural features:
★The use of suction hood structure, with high - pressure strong fan. The air suction is equipped with sound attenuation device, and the air source and electrical control are concentrated in the same operating cabinet. The distance from the main machine is not less than 1.5m.
★The operating side is fully closed and covered.Machine base and wallboard cast iron structure, wallboard thickness of 130mm. Universal joint drive.
★The corrugated roller material is made of 52 crmo alloy steel, after tempering, medium frequency quenching, surface polishing, corrugated roller diameter ¢293 mm, surface hardness above HRC60 degrees (optional, tungsten carbide roll and surface hardness HV1400). Key parts of the tile roller, pressure roller bearings using wafangdian high temperature bearings.
★The pressure roller ¢320 mm, surface grinding and chrome plated treatment; The cylinder is controlled to move up and down, and the material is medium carbon steel no.45, tempering and tempering treatment (with buffer device).
★The pneumatic control to glue back glue, glue spreader with 25 ¢215 mm diameter surface after polishing line after pit type checker processing hard chromium plating processing, scraping the rubber roller surface after grinding hard chromium plating processing.
★Raw materials of corrugated roller and pressure roller are provided by zhongyuan special steel co., LTD. The corrugated roller has a top middle height of 0.15mm on one side and a middle height of 0.075mm on the other side. Add limit device.
★The preheat roll ¢diameter of 600 mm.


Technical parameter:
  1. Working width:1400mm               
  2. Operation direction: left or right (according to the customer's workshop)
  3. the design speed: 120 m/min,      
  4. temperature range: 200-260 ºC    
  5. corrugated (UV or UVV)        
Roller diameter parameter:
  1. corrugated roller diameter:  ¢293 mm          
  2. pressure roller, ¢320 mm            
  3. glue roller diameter:  ¢215 mm             
  4. preheater diameter: ¢ 600 mm                
Powered motor parameters
Main drive motor: 11KW          suction motor :11KW 
           

ZDF conveyor bridge                                     
Structural features :
  1. This part is the main beam of the 20th channel, 16-beam, angle iron 63, column, etc. are connected.
  2. Both sides of the security fence, ladder , high-strength save people the word pedals, ensure the safety of personnel and easy to operate.
  3. Pull the paper shaft surface tension axis, feeding shaft by grinding hard chrome plated.
  4. Vacuum tension control, 5-inch suction tube, plus regulating valves, air flow can be infinitely adjustable.
  5. Dual front bezel correction guide column positioning, screw driver, fast and accurate positioning, walking steadily.

DHC-120 ELECTRIC THIN BLADE AND NC CUTTING MACHINE WITH AUTO STACKER
 120 Speed Steam Heating Automatic Corrugated Single Facer Line, 2 Ply Single Facer Line

Structural features:
  1. Germany  KEB servo motor drive controller, high-performance synchronous servo motor drive.
  2. Cutting Machine adopts inlaid front steel blade structure, hardened gear grinding backlash-free transmission, high precision and long life.
  3. Host wall of gray cast iron, rigidity, vibration resistance.
  4. stacking adopt gantry platform lifting,Reach a certain number of right-angle transverse,Three sections of the paper,Some hair design paper roll straight bend output,Second overlapping fixed-length buffer,three part points Pneumatic separate ,Accelerated export cardboard.Improve working efficiency.The maximum length of stacked is 1.3 meters .This machine is suitable for efficient production color printing business.
  5. Electrically adjust the knife and easy to operate.
  6. Using thin tungsten alloy steel knife,blade sharp,the using life is more than 8000000 meters.
  7. Automatic or manual knife sharpener can be divided trimming knife edge, increase productivity.
  8. Imported synchronous drive system, precision accurate, long life, low operating noise.
  9. From high-quality imported industrial computers and high-performance programmable controller configuration, lower computer control system.
technical parameters:
  1. The maximum working width:1400mm           
  2. operation direction:left or right(Determined in accordance with customer plant)
  3. The maximum mechanical speed:80-120m/min         
  4. Mechanical configuration:Computer spiral knife crosscutting
  5. Minimum cutting length:300mm            
  6. Maximum cutting length:9999mm
  7. Precision Cutter:±1mm(Uniform) ±1.5mm(Non-uniform)       
  8. 5 groups ¢200blades
Roller diameter parameters:
  1. Cross on the knife shaft diameter:¢200mm         Balancing done deal
  2. Cross under the knife shaft diameter:¢200mm       Balancing done deal
  3. Under the pull roller diameter:¢156mm            Balancing done deal
  4. Note: After all have been grinding rollers, hard chrome plated at (upper and lower arbor exception) processing.
Power motors and electrical parameters:
  1. main drive motor power:12.5KW  Full AC synchronous servo motors   
  2. Pull the paper motor power:3KW(Frequency Control)
  3. feed motor power:1.5KW(Frequency Control)             
  4. Transverse motor power:0.75KW(Frequency Control)

Mainly purchased parts, raw materials and origin:
Name of main partsBrands or place of originmaterial
AC servo motorShanghai futian12.5KW
Feeding frequency synchronous motorsTaiwan  CPG 
bearingHRB,ZWZ,LYC or zhejiang direction 
Up sleeveXianyang chaoyue 
Seat belt bearingZhejiang wuhuan 
ContacorFrance Schneider 
Proximity switches, photoelectric switchJapan OMRAN 
Flying shear servo control systemGerman KEB or weikeda 
Rotary encoderKorea Autonics 
Feeding frequency motorTaiwan delta 
HMITaiwan WEINVIEW or MCGS 
Sun wheelChina shenzhen 
Pneumatic componentsJapan SMC or Taiwan Airtac 



ZJZ glue KITCHEN system

Structural features:
  1. provide the starch adhesive to the corrugated single facer ,two glue machine and some other gluing equipment.
  2. Horizontal glue machine can meanwhile matched  withmain body glue and carrier glue, and mixing, glue large.
  3. Making room storage barrels adhesive solution was to use the glue pump rubber equipment storage barrels, adhesive solution for equipment.
  4. Storage barrels, plastic barrels with mixing device, avoid glue solution precipitation agglomerate.
  5. System unit with carrier vessel, main tank, storage tank, and send the glue pump, the back glue pump, etc.
  6. glue system adopt glue cycle,rest glue go back to the glue square cylinder,Liquid level float automatic control,the back glue a bucket of glue liquid being beaten back with glue equipment storage bucket,cycle for glue,Save the glue solution,prevent the glue solution in the rubber plate pasting and caking precipitation.
  7. Work has been completed, the residual gum dividend total pipeline with rubber equipment rubber pumped back rubber room storage barrels, for next time use.
  8. Responsible for technical guidance, teaching adhesive dispensing process.

technical parameters:
  1. Horizontal body glue mixer: one     
  2. Carrier glue mixer:one
  3. Storage glue mixer:one     
  4. Plastic buckets on double coater:one
  5. Two coating machine back plastic buckets :one  
  6. Plastic buckets on single machine :two
  7. Single machine back plastic buckets:two    
  8. Lose glue dispensing pumps:four
glue barrel diameter parameters:
  1. Horizontal body glue mixer:1250mm×1000mm×900mm
  2. Carrier glue mixer  diameter:  ¢800mm×900mm
  3. Diameter plastic bucket on Double Glue:¢800mm×1000mm    Plastic buckets on single machine:¢800mm×1000mm
  4. Storage tank diameter:      ¢1200mm×1200mm
Power motors and electrical parameters:
  1. Horizontal body glue mixer:      3KW                       
  2. Carrier glue mixer:        2.2KW(Ordinary three-phase)              
  3. output plastic pump motor :          2.2KW(Ordinary three-phase)            
  4. Storage Tank Motor        1.5KW(Ordinary three-phase)         
Mainly purchased parts, raw materials and origin:
Name of main partsBrands or place of originMaterial and type
motorHebei hengshui yongshun  
Lose glue dispensing pumpsHebei botou 
Skeleton profilestanggang 

120 Speed Steam Heating Automatic Corrugated Single Facer Line, 2 Ply Single Facer Line
120 Speed Steam Heating Automatic Corrugated Single Facer Line, 2 Ply Single Facer Line
120 Speed Steam Heating Automatic Corrugated Single Facer Line, 2 Ply Single Facer Line
120 Speed Steam Heating Automatic Corrugated Single Facer Line, 2 Ply Single Facer Line
120 Speed Steam Heating Automatic Corrugated Single Facer Line, 2 Ply Single Facer Line
120 Speed Steam Heating Automatic Corrugated Single Facer Line, 2 Ply Single Facer Line


 

You Might Also Like