Cable Waste Stripping Machine
China Cable Waste Stripping Machine, Find details about China Cable Stripping Machine, Waste Copper Wire Recycling Machine from Cable Waste Stripping Machine
Basic Info.
Model NO.
HSNQ18KO
Trademark
HSN
Origin
China
HS Code
8479909090
Model NO.
HSNQ18KO
Trademark
HSN
Origin
China
HS Code
8479909090
Product Desciption
Cable Stripping Machine
HSNQ18KO Cable Stripping Machine
Brief Introduction
The machine is for peeling off cable the outsourced plastic fore skin and metal core wire, because the cable diameter has different sizes and wire material and composition are not same, different cable should be used different suitable models. In the waste recycling industry, this machine makes operating system, save time and effort to more efficiently complete the recycling of waste wire and cable.
We have different capacity machine for you choose. And we also offer customized service.
Main Features
Simple Structure, Easy operation.
Safe production, Less electric cost.
Technical Specifications
Instructions for use
1. Before working, please check whether the machine operating is normal, feed according to the size of the cable diameter, in turn into the corresponding feed hole.
2. In order to extend durability of the blade, when feeding should be cut off connector of rubber cable, so as not to break the blade gap.
3. If the output cable occurrence of too deep and broken wire problem, pay attention to the following situation:
a) should adjust the feed gear, that is the two sides of the spring pressure.
b) when feeding, please check whether misplace the cable position of the feeding hole.
c) if the blade is new changed, whether the edge is too sharp application grinding stone slightly trim, moderate so far.
4. If output cable, the outer skin has been peeled off, but copper wire can't be exposed. There are mainly the following:
a) spring pressure is too loose, the pressure should be tightened;
b) the upper shaft rolling too deep, please use grinding stone to polish the upper shaft, but avoid to be over-polished, too much grinding easy to cause oily cable lines difficult to drive;
c) the wire diameter is small, or the upper and lower shaft gap is more, appropriate adjustment of the two-axis gap;
d) the processed cable has been hot, copper wire will not be easy to expose to the skin.
5. If after feeding, the crushing gear can not transmission the cable, the material stays in the middle, there are several situations:
a) check each belt if looseness;
b) check whether the spring pressure on both sides of each gear is too tight, there is no force, should relax the pressure;
c) cable oily too much, so that the two axes slip, should always clean the two axes.
Instructions for use:
HSNQ18KO Cable Stripping Machine
Brief Introduction
The machine is for peeling off cable the outsourced plastic fore skin and metal core wire, because the cable diameter has different sizes and wire material and composition are not same, different cable should be used different suitable models. In the waste recycling industry, this machine makes operating system, save time and effort to more efficiently complete the recycling of waste wire and cable.
We have different capacity machine for you choose. And we also offer customized service.
Main Features
Simple Structure, Easy operation.
Safe production, Less electric cost.
Technical Specifications
| Model | Power | Voltage | Cable Range | Blades | Hole | Output | Size | Weight |
| HSNQ18KOF | 3.0kw | 220V/380V | 1-50mm | 19 | 2+2+11 | 30m per minute | 70x61 x84cm | 110kg |
| HSNQ18KOB | 2.2kw | 220V/380V | 1-42mm | 23+5 | 1+5+5+10 | 30m per minute | 70x61 x84cm | 110kg |
Instructions for use
1. Before working, please check whether the machine operating is normal, feed according to the size of the cable diameter, in turn into the corresponding feed hole.
2. In order to extend durability of the blade, when feeding should be cut off connector of rubber cable, so as not to break the blade gap.
3. If the output cable occurrence of too deep and broken wire problem, pay attention to the following situation:
a) should adjust the feed gear, that is the two sides of the spring pressure.
b) when feeding, please check whether misplace the cable position of the feeding hole.
c) if the blade is new changed, whether the edge is too sharp application grinding stone slightly trim, moderate so far.
4. If output cable, the outer skin has been peeled off, but copper wire can't be exposed. There are mainly the following:
a) spring pressure is too loose, the pressure should be tightened;
b) the upper shaft rolling too deep, please use grinding stone to polish the upper shaft, but avoid to be over-polished, too much grinding easy to cause oily cable lines difficult to drive;
c) the wire diameter is small, or the upper and lower shaft gap is more, appropriate adjustment of the two-axis gap;
d) the processed cable has been hot, copper wire will not be easy to expose to the skin.
5. If after feeding, the crushing gear can not transmission the cable, the material stays in the middle, there are several situations:
a) check each belt if looseness;
b) check whether the spring pressure on both sides of each gear is too tight, there is no force, should relax the pressure;
c) cable oily too much, so that the two axes slip, should always clean the two axes.
Instructions for use:
You Might Also Like
Nc Studio Controller 3D Embossment Woodworking CNC Router En......
Peanut Oil Press Machine and Oil Extraction with High Oil Yi......
Cross Wooden Timber Acoustic Wall Panel for Sports Hall
China Supplier Anti-Fibrosis Drug Pirfenidone CAS 53179 -13-......
2021 Wholesale Professional High Quality Fractional Micro-Ne......
Tempered Glass Sight Glass Gauge Glass
Topleo Android TV Box The Cheapest 11.0 Km9 PRO Android Vide......
Automatic Hot Water Circulation Water Pump RS15/6gp
Stun Guns With CE ( CP6001 )
48V Lithium Battery 26 Inch Fat Tire Snow Mountain Bicycle B......
Segotep Export Morocco, Madeira, Azores. Gaming Chassis, ATX......
Hot Sale Fineness White Silica Sand/Quartz Sand for Manufact......