Products

Standard Vs Sump Pump

China Standard Vs Sump Pump, Find details about China Slurry Pump, Heavy Duty from Standard Vs Sump Pump

Model NO.
100RV-SP
Position of Pump Shaft
Vertical Pump
Pump Casing Combined
Verticaljoint Surface Pump
Mounting Height
Suction Centrifugal
Impeller
Closed
Usage
Pump, Pumps, Condensate Pump, Ash Pumps, Circulating Pump
Trademark
RT
Transport Package
Wooden Case
Origin
China
HS Code
8413709990
Model NO.
100RV-SP
Position of Pump Shaft
Vertical Pump
Pump Casing Combined
Verticaljoint Surface Pump
Mounting Height
Suction Centrifugal
Impeller
Closed
Usage
Pump, Pumps, Condensate Pump, Ash Pumps, Circulating Pump
Trademark
RT
Transport Package
Wooden Case
Origin
China
HS Code
8413709990




                                  High quality resisting abrasive heavy duty slurry pump
Type TSP pumps are vertical, centrifugal slurry pumps submerged in sump to work. They are designed for delivering abrasive, large particle and high density slurries. These pumps have no need of any shaft seal and sealing water. They can also be operated normally for insufficient suction duties.VSD here means Vertical Sump Duty Slurry Pump.
which is suited for the working condition of deeper level. The guide bearing construction is added to the pump on the basis of the standard pump, so the pump is with both more steady operation and wider application range, but flushing water should be attached to the guide bearing.
Wet parts of type VSD pump are made of abrasion-resistant metal.
All parts of type VSD pump immersed in liquid are lined with rubber outer liner. They are suited to transport no-edge angle abrasive slurry

Bearing Assembly The bearings, shaft and housing are generously proportioned to avoid problems associated with the operation of cantilevered shafts in the first critical speed zones.
The assembly is grease lubricated and sealed by labyrinths; the upper is grease purged and the lower protected by a special flinger. The upper or drive end bearing is a parallel roller type whilst the lower bearing is a double taper roller with preset end float. This high performance bearing arrangement and robust shaft eliminates
the need for a lower submerged bearing.
Column AssemblyCompletely fabricated from mild steel. 
CasingHas a simple bolt-on attachment to the base of the column. It is manufactured from a wear resistant alloy for the SP and from moulded elastomer for the VSDR.
ImpellerDouble suction impellers (top and bottom entry) induce low axial bearing loads and have heavy deep vanes for maximum wear resistance and for handling large solids. Wear resistant alloys, polyurethane and moulded elastomer impellers are interchangeable. The impeller is adusted axially within the casting during assembly by external shims under the bearing housing feet. No further adjustment is necessary.
Upper StrainerDrop-in metal mesh; snap-on elastomer or polyurethane for VSD and VSDR pumps. Strainers fit in column openings.
Lower StrainerBolted metal or polyurethane for SP; moulded snap-on elastomer for VSDR.
Discharge PipeMetal for VSD; elastomer covered for VSDR. All wetted metal parts are completely rust protected.
Submerged BearingsNone
AgitationAn external agitator spray connection arrangement can be fitted to the pump as an option. Alternatively, a mechanical agitator is fitted to an extended shaft protruding from the impeller eye.
MaterialsPumps can be manufactured in abrasive and corrosive resistant materials
Introduction:
Vertical Slurry Pump is a cantilever sump pump, semi-submerged to transport high abrasive and high density
lurries with large particles. It doesn't need any seal water and can work normally even insufficient liquid.
It is well designed for hard metal lined or fully rubber lined fitted, high flow rate with double suction semi-open
impeller design, and suction agitator is also available.
Size (discharge): 40mm to 300mm
Capacity: 7.28-1300 m3/h
Head: 3m-45 m
Handing solids: 0-79mm
Concentration: 0%-70%
Materials: high chrome alloy or anti-abrasive rubber
Mineral Processing Water Submersible Sand Mud Sump Mining Centrifugal Industrial Vertical Sp Spr Slurry Pump
Metal Lined Vertical Slurry PumpRubber Lined Vertical Slurry Pump
NoParts nameMaterialsNoParts nameMaterials
1Shaft45 High Strength Steel1Shaft45 High Strength Steel
2BearingChina Brand or SKF; NSK2BearingChina Brand or SKF; NSK
3Bearing HousingHT2503Bearing HousingHT250
4Bearing spacerStainless Steel4Bearing spacerStainless Steel
5BearingChina Brand or SKF; NSK5BearingChina Brand or SKF; NSK
6ShimStainless steel6ShimStainless steel
7ColumnStainless steel7ColumnStainless steel
8StrainerCast Iron8StrainerNatural Rubber
9Back linerUltra Chrome Alloy9Back linerAnti-abrasive Rubber
10ImpellerUltra Chrome Alloy10ImpellerAnti-abrasive Rubber
11Pump casingUltra Chrome Alloy11Pump casingAnti-abrasive Rubber
12Lower strainerCast Iron12Lower strainerNatural Rubber
13Discharge pipeStainless steel13Discharge pipeStainless steel
14Flushing pipeCarbon steel14Flushing pipeCarbon steel
15Coupling45# Steel15Coupling45# Steel
16Middle supporting partsStainless steel16Middle supporting partsStainless steel

Standard Vs Sump Pump

Standard Vs Sump Pump
Standard Vs Sump Pump
Standard Vs Sump Pump
Standard Vs Sump Pump

Standard Vs Sump Pump


If you need any others pump type, please free contact us


FAQ

Q:Are you manufacturer or a trading company?
A:We are manufacturer with more than 20 years experiences.

Q:How to customize pumps and mechanical seals ?
A:Customers could send us application data, we will select suitable pump and seal types, or client could send us drawings, We are well in OEM and ODM.

Q:How can I pay for my items? What is the payment you can provide?
A:Usually by T/T, 50%  payment in advance, the balance will be paid after inspection and before shipment. 

Q:How long is production lead time?
A:Normally 15 working days. If client need urgently, we have a huge spare parts stock, we could finish assembly and testing in 7 days.

Q:What is the shipping terms you can provide?
A:Depnends on customer's requirements, we can provide different transportantin terms, such as EXW, FOB, CIF.

Q:Who is in charge of after-sales?
A:Ruite has professional after sales service team, we will follow up the client's comments and suggest them good solutions. Solve client's problems and keeping the clients profit.


 

Send message  Get product Offer & Brochure!!!

↓↓↓

You Might Also Like