Products

M-FT Output Signal Trigger

China M-FT Output Signal Trigger, Find details about China Traveling Wave Current Detection Integrator, Fault Current Detection Integrator from M-FT Output Signal Trigger

Model NO.
M-FT
Theory
Integrate,Amplify,Convert Electric Signals
Power Meter Connection
No
Measured Signal
High Frequency Pulse Current Signals
Type
Signal Amplifier/Integrator/Converter
Certification
RoHS, ISO, CE
Customized
Customized
Power Supply
Dual or Single Power Supply
Power Consumption
55MW or 15 MW
Ratio
1&7 Pin Output 0.5V/Ka; 8 Pin Trigger 1V/100A
Pulse Bandwidth
>10MHz
Application 1
Lightning Monitoring
Application 2
Current Detection of Transmission Lines
Application 3
Current Detection of Distribution Lines
Application 4
Power Frequency Steady State Current
Application 5
Fault Current Detection
Application 6
Traveling Wave Current Detection
Application 7
Power Frequency and High Frequency Current
Installation Type
User Integrated Embedded Installation
High Frequency Pulse Current Signals
3/5μs, 8/20μs, 10/ 350μs
Frequency
up to 10MHz
Peak Value
1A to Hundreds of Ka
Trademark
MEATROL
Transport Package
Polybag and Export Carton
Specification
64.54*6.4*27mm
Origin
China
HS Code
8517699000
Model NO.
M-FT
Theory
Integrate,Amplify,Convert Electric Signals
Power Meter Connection
No
Measured Signal
High Frequency Pulse Current Signals
Type
Signal Amplifier/Integrator/Converter
Certification
RoHS, ISO, CE
Customized
Customized
Power Supply
Dual or Single Power Supply
Power Consumption
55MW or 15 MW
Ratio
1&7 Pin Output 0.5V/Ka; 8 Pin Trigger 1V/100A
Pulse Bandwidth
>10MHz
Application 1
Lightning Monitoring
Application 2
Current Detection of Transmission Lines
Application 3
Current Detection of Distribution Lines
Application 4
Power Frequency Steady State Current
Application 5
Fault Current Detection
Application 6
Traveling Wave Current Detection
Application 7
Power Frequency and High Frequency Current
Installation Type
User Integrated Embedded Installation
High Frequency Pulse Current Signals
3/5μs, 8/20μs, 10/ 350μs
Frequency
up to 10MHz
Peak Value
1A to Hundreds of Ka
Trademark
MEATROL
Transport Package
Polybag and Export Carton
Specification
64.54*6.4*27mm
Origin
China
HS Code
8517699000
M-FT Output Signal TriggerM-FT Output Signal Trigger
M-FT Modular integrator 

The current detection of transmission and distribution lines often needs to detect the steady-state current, fault current and traveling wave current at the same time. The traditional method is to use different sensors to detect different current signals. Therefore, the system is with redundant devices and complex constructure, which not only wastes a lot of installation time, but also has poor reliability.

In order to solve the above problems, ROGOWSKI TECHNOLOGY (SHANGHAI) CO.,LTD developed a fire-new modular integrator M-FT after years of technical research.Configuration equipped with broadband Rogowski coils and one M-FT modular integrator, which is especially designed for outdoor embedded installation, it realizes the signal detection of power frequency current and high frequency current. The advantage of compact appearance, simple application and directly installation on application mainboard, quickly shorten development period.

M-FT integrator can measure a variety of high frequency pulse current signals, such as 3/5μs, 8/20μs, 10/350μs. The frequency can reach up to 10MHz or even more, and the peak value can cover 1A to hundreds of kA. In the range of 10% - 100%, the linearity is better than 1%.

The broadband Rogowski coils produced by ROGOWSKI TECHNOLOGY (SHANGHAI) CO.,LTD, which is with opening model and easy installation, has the advantages that traditional CT can't do. The available coil series are H-FCT, H-ZRC, H-MRC and rigid coil RCT.

The modular integrator has two versions, the dual power supply version M-FT-D   (±3V~±15V) and the single power supply version M-FT-S (+3V~+5V). One Rogowski coil corresponds to three outputs, including one power frequency output and two high frequency pulse outputs. The output signal is a voltage signal, and its waveform is proportional to the original current wave. The ratio can be set according to the actual demand.

For example: 1 pin output power frequency current 0.5V/kA; 7 pin output high frequency current 0.5V/kA; 8 pin 1V/100A, 8 pin output signal can be used as trigger.
 
Structure diagram:
 



M-FT Output Signal TriggerM-FT Output Signal Trigger
Needle arrangement:

M-FT Output Signal Trigger

Application:

Lightning wave measurement; discharge current measurement; traveling wave measurement; lightning monitoring system; fault location, etc.

Waveform example: 8/20us lightning current

 

M-FT Output Signal Trigger

Electrical parameters

Power supply:
  1. Dual power supply version M-FT-D: ±3V to ±15V
  2. Single power supply version M-FT-S: +3V to +5V
Settable lifting voltage: normally +1.8V / +1.25v / +2.5V
Power Consumption:55mW (All configuration is fully on for dual power supply version, ±5V power supply);  
Power consumption: 15 mW for single output with filter; 10mW for single output without filter.
Single power supply version has slightly higher power consumption .
Ratio:customized three output
Pulse bandwidth:>10MHZ
Operation temperature:-40ºC to 85ºC

Key definitions for Single power supply version M-FT-S and Dual power supply version M-FT-D :
 
Pin numberM-FT-S M-FT-DPin description
Pin 9GNDGNDGND
Pin 8OUT COUT CSettable ratio                     Selectable filtering out power frequency 
Revocable output for saving power consumption
Pin 7OUT BOUT BSettable ratio
Selectable filtering out power frequency 
Revocable output for saving power consumption
Pin 6GNDGNDGND
Pin 5+VDD+VDDPositive power supply +VDD
Dual power supply version M-FT-D: power supply ±3V to ±15V
Single power supply version M-FT-S: power supply +3V to +5V
Pin 4GNDGNDGND
Pin 3GND-VSSPositive power supply +VDD
Dual power supply version M-FT-D: power supply ±3V to ±15V
Single power supply version M-FT-S: power supply +3V to +5V
Pin 2GNDGNDGND
(Power ground and signal ground are not separated)
Pin 1OUT AOUT APower frequency output
Settable ratio
Revocable output for saving power consumption

Note: Single power supply version M-FT-S can be with lifting voltage output, eg. with lifting 2.5V/1.2V/1.8V output, connecting to input 5V/3.3V ADC.

        
PCB attention points:
The power pin should be placed close to the capacitor combination of 10uF to 100nF; The high frequency output needs to be routing wired underground, please refer to the high frequency signal wiring rules.


1. The subassembly is integrated designed with Rogowski coil and modular integrator, which is connected directly through SMA or MMCX connector.

2. Output mode is using one Rogowski coil corresponding with 3 ratios. On the premise of using one Rogowski coil, the integrator outputs one power frequency signal and two traveling wave signals with different ratios, and the high frequency signal can be filtering out power frequency or not.

3. * Significance of filtering out power frequency: The high frequency pulse wave has little energy distribution below 400Hz. Even if it is filtered out, the original waveform will not be greatly affected. But it brings great convenience for waveform analysis. In this way, the starting position of the waveform is always at bit 0, rather than starting on a power frequency waveform.
 
M-FT Output Signal Trigger
M-FT Output Signal Trigger









More applications and solutions of Rogowski coils:
Special Rogowski coil+Integrator for Fault Indicator
Rogowski coil NZ special for high temperature Electric Furnace
Rogowski Coil Sensor special for Lightning Current
Ø8 High Frequency: H-FCT,
Ø12 High Voltage 36kV: D-SRC ...
Application cases in high frequency pulse welding machine: current up to 1500kA
Detection coil applicated to Power generation equipment of China's second largest hydroelectric station: current up to 500kA
Rogowski coil application in Draught Fan, lightning current up to 300kA

M-FT Output Signal TriggerM-FT Output Signal TriggerM-FT Output Signal TriggerM-FT Output Signal Trigger





 

You Might Also Like