Ad-1100 Oaliss Atlas Copco Bolaite Pneumatech Heated Purge Desiccant Air Dryer
China Ad-1100 Oaliss Atlas Copco Bolaite Pneumatech Heated Purge Desiccant Air Dryer, Find details about China Compressed Air Dryer, Air Compressor Dryer from Ad-1100 Oaliss Atlas Copco Bolaite Pneumatech Heated Purge Desiccant Air Dryer
Basic Info.
Model NO.
AD-1100
Warranty
1 Year
Video Outgoing-Inspection
Provided
Cetification
GB
Capacity
1.0-26 M3/Min
Weight
162kg
Trademark
Atlas Copco- Pneumatech
Transport Package
Wooden Case
Specification
1050x660x1130mm
Origin
Wuxi
Model NO.
AD-1100
Warranty
1 Year
Video Outgoing-Inspection
Provided
Cetification
GB
Capacity
1.0-26 M3/Min
Weight
162kg
Trademark
Atlas Copco- Pneumatech
Transport Package
Wooden Case
Specification
1050x660x1130mm
Origin
Wuxi
Package size per unit product
2600.00cm * 1450.00cm * 3000.00cm
Gross weight per unit product
4500.000kg
Product Desciption
How to remove the water?
There are several ways to remove water and moisture from compressed air.
1. The first method is overcompression, the pressure is increased to a level above the required compressed air pressure and at this higher pressure the free water droplets are removed. In the next step, the pressure is decreased to the required compressed air pressure. From this stage, only water vapor is present in the compressed air, the relative humidity dropped below 100%.
2. A second method is cooling, the compressed air is cooled down to a lower temperature. At this lower temperature, the relative humidity exceeds 100% and free water droplets are formed. Those free water droplets are collected and removed. In the next step the temperature of the compressed air is increased again. From
this stage, only water vapor is present in the compressed air, the relative humidity dropped below 100%.
3. As third method chemical drying is often used, the moisture is removed by absorption or adsorption in a certain substance. With absorption, the moisture is captured in a hygroscopic liquid or powder. The moisture is attached to this material and needs to be removed and replaced by new material for further operation.
With adsorption, the moisture is captured in hygroscopic beads. The moisture molecules are transported into the pores through diffusion and are accumulated through physical binding and capillary condensation. In this case, when the beads are saturated, they have to be regenerated before they can start adsorbing again. The regeneration
can be done by heating the beads or by sending extreme dry air over the beads. In both cases the water retaining forces are broken and the water molecules are removed.
Specification
Item | Description |
Type | Refrigerated dryer |
Warranty | 1 Year |
Applicable Industries | Hotels, Garment Shops, Building Material Shops, Manufacturing Plant, Machinery Repair Shops, Food & Beverage Factory, Farms, Restaurant, Home Use, Retail, Food Shop, Printing Shops, Construction works, Energy & Mining, Food & Beverage Shops, Other, Advertising Company |
After Warranty Service | Spare parts |
Local Service Location | Thailand, Vietnam, Pakistan, Russia, Sri Lanka |
Showroom Location | Thailand, Vietnam, Pakistan, Russia, Sri Lanka |
Video outgoing-inspection | Provided |
Machinery Test Report | Provided |
Marketing Type | New Product 2021 |
Place of Origin | China |
Brand Name | Atlas Copco - Pneumatech Oaliss |
Types of compressed air dryers
Refrigeration dryers
Refrigeration dryers are used for PDPs between +3°C/37.4°F to +10°C/50°F with the freezing point of water (0°C/ 32°F) as the lower limit.
By cooling the compressed air with a closed refrigeration
system a large amount of water condenses and can be
separated. Afterwards the compressed air is reheated
with the incoming air to around room temperature. In this
way the moisture content of the air stays well below the
maximum moisture holding capacity at normal (nonfreezing) ambient temperatures, meaning that the relative humidity stays below 100%. It is recommended to stay below 50% relative humidity to avoid any condensation to happen on local cold spots of the piping network.
Adsorption dryers
Adsorption dryers are used when PDPs from -10°C/14°F down to -70°C/-94°F are to be achieved.
They make use of a material which has a high affinity
to attract moisture, so called hygroscopic material
or desiccant. The adsorption of moisture causes the
desiccant to be gradually saturated with water.
Therefore, the desiccant needs to be regenerated
regularly to regain its drying capacity. Adsorption dryers
are typically built with two drying vessels ("towers")
for that purpose: the first tower will dry the incoming
compressed air while the second one is being
regenerated. To ensure continuity, each vessel switches
tasks when the other one is completely regenerated.
Oaliss's objective is to be "Your very own system provider". To fulfill this objective, Oaliss pays great attention to customer's real needs and concerns, then provides feasible solutions. Oaliss chooses the most reliable suppliers from the industry and tests its performance before installing on our equipment. Product quality is our paramount goal. In the meantime, we do our best to fill the gaps between price and energy efficiency. Our equipment will be reliable enough to use and the price low enough to purchase. Combined with these distinct features, our high quality and variable products have been accepted by customers from various industries. Oaliss-your very own system provider.
Oaliss-your very own system provider.
plastics, steel industry, rubber, mechanical, blow molding, color sorter machine, shipyard, sandblasting,
metallurgy, etc.
To provide the right equipment to you, please send us your detailed requirements.
1 Q: How about the quality of products?
A: We are an authorized distributor of Atlas Copco. The quality and service could be assured.
2 Q: How long is your delivery lead time?
A: If there is stock, the lead time is about 3 working days after we get the payment if need to
be produced, it depends.
3 Q: How about your overseas after-sale service?
A: (1)Provide customers with installation and commissioning online instructions.
(2)Worldwide agents and after service available.
4 Q: Can you accept OEM&ODM orders?
A: Yes, we have a professional design team, OEM&ODM orders are highly welcomed.
You Might Also Like
Zinc It Done Water-Based Galvanizing Spray Paint Aqueous Gal......
EPA/Carb Certificated Fuel Line Fuel Hose for Garden Machine......
100g high performance desiccant in Tyvek
Truck Spare Parts Weichai Engine Intake Rocker Arm Best
Art Glass Smoking Water Pipe ( AY 020)
Pdadmac 40% Cationic Polymer for Sludge Dewatering
Hot-Sale HDI Multilayer Printed Circuit Board Fr4 PCB Power ......
High-End Wall Mounted Storage Holder Rack for Kitchen Goldmi......
Rth -1100A Non Woven Sheet Cutting Machine Sheet Label Cutti......
Non Crosslinked Hyaluronic Acid Meso Filler for Lip Injectio......