Products

Sgp Film for Glass Laminating

China Sgp Film for Glass Laminating, Find details about China EVA Interlayer, Hot Melt Film from Sgp Film for Glass Laminating

Model NO.
JX5010
Layer Type
Bullet-Resistant Glass
Function
Electromagnetic Shielding
Intermediate Film
Pu
Melting Point
Insulated Glass
Production
Dry Laminated Glass
Color
Clear
Shore Hardness
80ha
Light Transmittance
92%
Water Absorption
0.1%
Adhesion to Glass
90n/Cm
UV Block Rate
98%
Impact Resistance Against Shoot-Bag
Qualified
Trademark
Jiaxing
Transport Package
Rolls and Cartons
Specification
0.38mm, 0.76mm, 1.14mm, 1.52mm
Origin
China
HS Code
39201090
Model NO.
JX5010
Layer Type
Bullet-Resistant Glass
Function
Electromagnetic Shielding
Intermediate Film
Pu
Melting Point
Insulated Glass
Production
Dry Laminated Glass
Color
Clear
Shore Hardness
80ha
Light Transmittance
92%
Water Absorption
0.1%
Adhesion to Glass
90n/Cm
UV Block Rate
98%
Impact Resistance Against Shoot-Bag
Qualified
Trademark
Jiaxing
Transport Package
Rolls and Cartons
Specification
0.38mm, 0.76mm, 1.14mm, 1.52mm
Origin
China
HS Code
39201090
Sgp Film for Glass LaminatingProduction introduction:
In order to achieve the desired strength or higher resilience, 2 or more layers of
SolarGlas materials may be needed to overlap between the 2 layers of glass. The vacuum bag process can be suitable for multilayer laminated glass with any layers of film. The operation range of the rolling process is relatively narrow.

Rolling process:

For two layers of SolarGlas material (0.76 mm thickness, 0.89 mm), pre­ compression can be easily done using standard roll­on methods. Before joining, clean each piece of SolarGlas material with a viscous roller to remove possible dust and other contaminants. , You can adjust the roll speed of the line to ensure a good edge sealing effect and the end bubble­free issue.
Usually, more than two pieces of SolarGlas material sandwiched in two pieces of glass can also be pre pressed by rolling technology, but the total thickness of sandwich materials should be controlled at no more than 5 mm. If the total thickness is greater than  5 mm, the following consequences may happen.
  1. Because SolarGlas material can not get enough heat, it cannot fully bond with each other during preloading process, resulting in high pressure air bubbling into the autoclave. (Fig. 18).
In order to improve the bonding of SolarGlas materials to each other, premature sealing of the glass with the outermost layer can occur if the pre­press temperature is increased, potentially causing bubble­in.
 

Figure 18

Vacuum bag process:
If done correctly, the vacuum bag process makes very good laminated glass with more than two layers of SolarGlas material stacked without the risk of poor defects such as air bubbles, etc. For thicker or more layers of material The same vacuum bag process also needs to pay attention to the following key steps:
  1. As the number of lamination increases, a corresponding increase in cooling time is required, and usually the cooling time is adjusted according to some conditions (such as

the degree of vacuum, the size of the vacuum pump and the size of laminated glass, etc.), often based on actual experience.
  1. with the increase of the thickness of the SolarGlas material and the size of the glass, the thermal insulation time of the autoclave should also be appropriately increased.
  2. To minimize the haze of the finished glass, it is necessary to ensure that the autoclave fans are turned off and the autoclave fans are switched off when the surface temperature of the glass is less than 38 degrees Celsius, and cooling water is used to force cooling.
Certificates:
Sgp Film for Glass Laminating
Packing and Samples:
Sgp Film for Glass Laminating
Sgp Film for Glass LaminatingCompany introduction:
Linqu Jiaxing Plastic Co.,Ltd.,is built in 2004, is a professional and high-tech manufacturer of release film,surface protect film,hot melt EVA film,high temperature tape/PI tape,aluminium foil tape,glass fiber tape ect. Related plastic products, our products are widely applied on electronic industry,building material and new energy ect. Many areas;

Main products:
1.surface protection film;
2.glass protection film;
3.laser cutting film for steel;
4.PI tape;
5.PET high temperature tape;
6.ESD shielding tape;
7.double sided foam tape;
8.filament tape;
9.conductive tape;
10.reflective tape;
11.hot melt EVA film;
12.HDPE release film;
13.PET release film;
14.PP release film;
15.self adhesive high temperature tape for steel bar;

Jiaxing Plastic,is located in Weifang city- well-known as International Kite Capital,which adjoin with Qingdao port; during over ten years' development,Jiaxing Plastic covers an area of over 40 thousand square meters, uphold 2 ten thousand class dust free workshops,there are 5 sets coating machines,2 sets six colors printing machines and 1 set casting machine; Jiaxing Plastic,with a strong technical strength,has over 200 employees, A group of competent management teams and a team of professional technologists, also R & D team led by experts.
Jiaxing Plastic presently passed ISO9001,SGS certificates, products are exporting to over 30 countries and areas,including USA,UK,RUSSIA ect., acquire new and old customers alike.
Warmly welcome to your inquiry and visit!

 

You Might Also Like