DN800 Pipe Size 4-20mA Output Water Flow Meter Temperature Liquid Electromagnetic Flow Meter
China DN800 Pipe Size 4-20mA Output Water Flow Meter Temperature Liquid Electromagnetic Flow Meter, Find details about China Flow Meter Magnetic, Flow Meter Electromagnetic from DN800 Pipe Size 4-20mA Output Water Flow Meter Temperature Liquid Electromagnetic Flow Meter
MLF electromagnetic flow meter, composed of sensor and converter, works based on Faraday's law of electromagnetic induction law. It is used to measure electrical conductivity of liquid or solid. Generally, the electrical conductivity should be over 5υS/cm(electrical conductivity of tap water, raw water is about 100~500υS/cm),It can also be used to measure various media like acid, alkali, saline solution, paper pulp or pulp and so on. But these media can't contain a lot of magnetic materials and bubbles.
MLF electromagnetic flow meter is a kind of instrument which is used for measuring the flow conductivity liquid. The meter is widely used in flow measuring of Metallurgy, Chemical Industry, Paper Industry,Environmental Protection, Oil Industry, Textile Industry, Food Industry and City Administration, Water Works,etc.
The principle of the sensor is based on Faraday's law of electromagnetic induction. It is installed a pair of detection electrodes on the pipe wall,where the measurement pipe axis and magnetic field lines are vertical. When the conductive liquid cuts magnetic field lines and produces induced electromagnetic force.Which can be measured by the two electrodes on the meter pipe.The result can be calculated by formula: Induced electromotive force,(flow signal)
E=KBDVE--Induced electromotive force,V;
K--meter constant;
B--Magnetic flux density,T;
D--Internal diameter of measuring pipe,m;
V--Average velocity of pipe section,m/s.
1MLF Series Electromagnetic Flow Meter
Assume the volume of liquid as qv(m3/s),qv=πD2V/4),so in the formula E=(4kB/πD)qv=kqv, K is meter constant,K=4kB/πD.
Actually, the electromagnetic flow meter consists of two parts, transmitter and sensor, the measuring electrodes inspect the electromotive force, and transmit to the converter, the converter provides excitation current. E is usually called a flow signal, after processing the flow signal by converter, output 4~20 mA/pulse(or frequency) signal which is proportional to the flow rate, then the flow rate recording,adjusting can be achieved.
The MLF electromagnetic flow meter is for explosive proof design.
- It as the function of low conductivity measurement.
- It has Multi languages for option to satisfy different customers' requirements.
- It has the function of self-adjustment and self-checking.
- A variety of outputs are optional: RS485, Profibus, 4-20mA, Frequency, Pulse.
| MLF Type | Divided Type | Integrated Type | Explosive Proof Integrated Type | Battery Powered Type | Heat Energy Type |
| Accuracy | ±0.2% or ±0.5% | ||||
| Pipeline Diameter | DN10 DN15 DN20 DN25 DN32 DN40 DN50 DN65 DN80 DN100...DN2000 | DN10-DN600 | DN25-DN2000 | ||
| Flange | GB, ANSI, JIS, BS, Others | ||||
| Pressure | DN10-DN600 1.0 1.6 2.5 4.0MPa | ||||
| DN700-DN2000 0.6 1.0 1.6MPa | |||||
| Liner Material | CR, PTFE, PU, Hard Rubber, PFA, FEP(F46) | ||||
| Conductivity | ≥5µs/cm(Please contact us if it is less than 5µs/cm) | ||||
| Electrode | 316L SS, Hb, Ta, Ti, Hc, Tungsten Carbide, Others | ||||
| Protection Class | IP65, IP66, IP67, IP68 | ||||
| Medium Temperature | -25~180ºC (Please refer to liner material) | -25~80ºC(Please refer to liner material) | -25~180ºC (Please refer to liner material) | ||
| Ambient Temperature for Accuracy Influence | <±0.1%> | ||||
| Repetability | ≤±0.1% or ±0.25% | ||||
| Analog Output Error | ≤±0.02mA | ||||
| Velocity | 0.3~10m/s | ||||
| Electrical connection | M20x1.5 Seal Cartridge, GB1/2, NPT1/2 | ||||
| Output | 4-20mA, Pulse, RS485, Hart, Profibus | ||||
Selection of Liner Material
| Liner Material | Main Performance | Application |
| PTFE | 1. Have the most stable chemical properties in plastic and resistance to boiling hydrochlor and sulfuric acid, nitric acid aqua regia, strong alkali, and all kinds of organic solvents, but can not resist the corrosion of chlorine trifluoride, high temperature nitrogen trifluoride, liquid fluorine, liquid oxygen and ozone. 2. Low abrasion resistance. 3. Low negative pressure resistance | 1. -25~140ºC 2. Strong corrosion medium, like strong acid and alkali 3. Healthcare medium |
| CR | Oil proof, solvent resistance, oxidatite resistance and the resistance to the erosion of common medium like acid, alkali, salt, etc. | 1. <80ºC 2. Be able to measure sewage and mud |
| PU | 1. Very good abrasive resistance, flexibility. 2. Low acid and alkali resistance. | 1. <65ºC 2. Neutral strong abrasion resistance medium |
| Hard Rubber | 1. Good resistance to room temperature, hydrochloric acid, acetic acid, oxalic acid, ammonia, phosphoric acid and 50% sulfuric acid, sodium hydroxide, potassium hydroxide 2. Avoid strong oxidants | 1. <80ºC 2. General acid, alkali, salt solution |
| PFA | 1. Can be used for most corrosive medium like acides, alkalis, and strong oxidant. 2. High material strength, resistance to aging, better than PTFE, EFP in high temperature 3. Injection molding for higher negative pressure | 1. 40~180ºC 2. Strong corrosion medium, like strong acid and alkali 3. Healthcare mdium |
| FEP(F46) | 1. Hydrophobicity and non-viscous 2. Corrosion resistance is inferior to PFA 3. Negative pressure | 1. 40~180ºC 2. Strong corrosion medium, like strong acid and alkali 3. Healthcare mdium |
Selection of Electrode Materials
| Electrode Material | Main Performance |
| 316L | Good resistance to the corrosion of nitric acid, <5% sulfuric acid under room temperature, acetic acid, alkaline fluid, sulfite under certain pressure, seawater and scetic acid, etc. It can be widely used in petrochemical urea, vinylon. |
| Hb | Good resistance to the all the concentration of hydrochloric acid below the boiling point, also resistance tothe corrosion of non-oxidizing acid, alkali, salt like sulfuric acid phosphoric acid hydrofluoric acid, organic acids. |
| Hc | Resistance to the corrosion of oxidizing acids like metric acid, mixed acid. The mixture of chromium acid and sulfuric acid, and salts of oxidative, like Fe3+, Q3+, and some other oxidants, like hypochlorite salt solution higher than normal tmperature and seawater. |
| Ti | Resistance the corrosion of seawater, various chlorides, hypochlorite, oxidizing acid(including fuming nitric acid), and organic acid or alkali, but don't be resistance to the corrosion of pure reducint acid(like sulfuric acid, hydrochloric acid). But if acid includes oxidants(like nitric acid, Fe3+, Q3+), the corrosion resistance will decrease. |
| Ta | Good corrosion resistance similar to glass. Resistance to the corrosion of chemical medium(including hydrochloric acid and fumiing sulfuric acid), but can not be used for sodium hydromide fluid. |
| Pt-Ir | Have good corrosion resistance of all acid, and can be resistance to the corrosion of alkali, all salt except aqua regia, ammonium slat and few other medium |
| Tungsten Carbide | For pulp and sewage, good resistance to solid particle interference. |
| MLF Series Electromagnetic Flow Meter Configuration | |||||||||||||||||||||||
| Model | MLF | ||||||||||||||||||||||
| Sensor Installation | S | Flange Type Sensor | |||||||||||||||||||||
| C | Insertion Type Sensor | ||||||||||||||||||||||
| O | Others | ||||||||||||||||||||||
| Pipeline Diameter | 10 | 10mm | |||||||||||||||||||||
| 15 | 15mm | ||||||||||||||||||||||
| 20 | 20mm | ||||||||||||||||||||||
| ...... | |||||||||||||||||||||||
| 2000 | 2000mm | ||||||||||||||||||||||
| Electrode Installation | F | Standard Fixed Type | |||||||||||||||||||||
| Electrode Material | A | 316L SS | |||||||||||||||||||||
| B | Hb | ||||||||||||||||||||||
| C | Ta | ||||||||||||||||||||||
| D | Ti | ||||||||||||||||||||||
| E | Hc | ||||||||||||||||||||||
| F | Tungsten Carbide | ||||||||||||||||||||||
| G | Others | ||||||||||||||||||||||
| Liner Material | R | Rubber | |||||||||||||||||||||
| P | PTFE | ||||||||||||||||||||||
| O | Others | ||||||||||||||||||||||
| Pipe Material | B | 304 SS (Standard) | |||||||||||||||||||||
| C | 316 SS | ||||||||||||||||||||||
| Flange Type | G | GB (Standard) | |||||||||||||||||||||
| A | ANSI | ||||||||||||||||||||||
| J | JIS | ||||||||||||||||||||||
| B | BS | ||||||||||||||||||||||
| O | Others | ||||||||||||||||||||||
| Flange Material | A | 304 SS | |||||||||||||||||||||
| B | 316 SS | ||||||||||||||||||||||
| C | #20 Carbon Steel (Standard) | ||||||||||||||||||||||
| Cover Material | D | 304 SS | |||||||||||||||||||||
| E | 316 SS | ||||||||||||||||||||||
| F | Carbon Steel+ Epoxy Metallic Paint (Standard) | ||||||||||||||||||||||
| Matching Flange | 0 | Without Matching Flange (Standard) | |||||||||||||||||||||
| 1 | With Matching Flange | ||||||||||||||||||||||
| Ground Ring | 0 | Without Ground Ring (Standard) | |||||||||||||||||||||
| 1 | With Ground Ring | ||||||||||||||||||||||
| Rated Pressure | 10 | 1.0MPa | |||||||||||||||||||||
| 16 | 1.6MPa | ||||||||||||||||||||||
| 25 | 2.5MPa | ||||||||||||||||||||||
| 40 | 4.0MPa | ||||||||||||||||||||||
| Working Temperature | E | ≤60ºC | |||||||||||||||||||||
| H | ≤180ºC(Divided Type) | ||||||||||||||||||||||
| Type | I | Integrated Type | |||||||||||||||||||||
| D | Divided Type | ||||||||||||||||||||||
| Output | P | Pulse | |||||||||||||||||||||
| A | 4-20mA | ||||||||||||||||||||||
| G | RS485 | ||||||||||||||||||||||
| H | Hart | ||||||||||||||||||||||
| Q | Others | ||||||||||||||||||||||
| Power Supply | 0 | 220VAC | |||||||||||||||||||||
| 1 | 24VDC | ||||||||||||||||||||||
| 2 | Battery-powered | ||||||||||||||||||||||
| Protection Class | 0 | IP65 (Integrated/Divided Type) | |||||||||||||||||||||
| 1 | IP67 (Divided Type) | ||||||||||||||||||||||
| 2 | IP68 (Divided Type) | ||||||||||||||||||||||
| Other Features | R | Heat Energy Function | |||||||||||||||||||||
| P | With PT1000 | ||||||||||||||||||||||
| B | Without PT1000 | ||||||||||||||||||||||
| Explosion Proof | 0 | None | |||||||||||||||||||||
| EX | Explosive Proof | ||||||||||||||||||||||
The electromagnetic flowmeter has a self-diagnostic function. In addition to power supply and hardware circuit failures, the system also alarms other failures in general use. These messages will give corresponding prompts in the lower right corner of the screen.
1 Maintenance and repair
a) The sensor installation site should meet the requirements of Section 4, please keep the housing tidy;
b) The transmitter should be placed in a clean, ventilated and dry place;
c) It needs to be inspected every two years. For high-precision users, the instrument needs to be submitted for review.
2 Transportation and storage
a) The instrument must be packaged before transportation, and be handled with care when loading and unloading.
b) The storage place must be dry and ventilated to avoid corrosive gases, and the ambient temperature should not be too low or too high;
c) The storage time should not exceed three years.
3. Unpacking inspection
a) The package cannot be opened with a heavy hammer, be careful not to damage the instrument
b) Check the contents carefully according to the packing list.
Melan Measurement & Control Instruments is located in Shanghai City. It is a high-tech manufacturer specialized in the design, development, manufacturing and sale of measurement and control instruments.
Our products are widely used in various fields, including electricity, chemical industry, metallurgy, brewing, oil and gas, textile, water conservancy, environmential protection, etc.
We own independent-courtyard modemized manufacturing workshops and an open office building. Melan has accumlated production and management experience in instruments from European and American and domestic famous companies.
We own first-class talent team, and all the products have reached advanced level at home and abroad. We provide our customers with complete and professional test control solutions and high-tech and high-quality products.
Melan is your reliable friend and partner. We are willing to try our best as dedication and perfection as motivation.
Q: How long will you give me the reply?
A: We will contact you in 5 hours as soon as we can.
Q: What is the warranty of your prducts?
A: Our warranty is 12 months after the shipping date.
Q: What is the lead time of your products?
A: Normally our factory lead time is 10-12 working days.
Q: Can I OEM your products?
A: OEM and ODM customization are welcomed.
Q: What is your MOQ?
A: We have no MOQ limit, small quantity order is acceptable.
Q:What is the transport?
A: Express such as DHL, FedEx, UPS for freight prepaid, and we can also use your own courier account to do the freight collect. For more goods we can arrange by air or by sea.
You Might Also Like
Zinc It Done Water-Based Galvanizing Spray Paint Aqueous Gal......
EPA/Carb Certificated Fuel Line Fuel Hose for Garden Machine......
100g high performance desiccant in Tyvek
Truck Spare Parts Weichai Engine Intake Rocker Arm Best
Art Glass Smoking Water Pipe ( AY 020)
Pdadmac 40% Cationic Polymer for Sludge Dewatering
Hot-Sale HDI Multilayer Printed Circuit Board Fr4 PCB Power ......
High-End Wall Mounted Storage Holder Rack for Kitchen Goldmi......
Rth -1100A Non Woven Sheet Cutting Machine Sheet Label Cutti......
Non Crosslinked Hyaluronic Acid Meso Filler for Lip Injectio......